Add build tests for the IT8801 MFD drivers, including GPIO,
Input and PWM functionalities.
GPIO, Input test: west build -p always -b native_sim
PWM test: west build -p always -b it82xx2_evb
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
IT8801 support GPIO alternate function switching.
Some GPIO pins can be switched as KSO or PWM function.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
The IT8801 is an I/O expander that provides GPIO, PWM, Keyboard
functions via the I2C bus.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
For Zephyr Cortex-A Core supports on NXP boards imx8mm, imx8mn, imx8mp,
imx93 and imx95, currently use DDR DRAM memory as Zephyr memory, so
change RAM dts nodes name to be "dram" in order to reduce confusion.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Rename "nxp,kinetis-adc12" compatible to "nxp,adc12" to remove the
device family from its name.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
The initial proposal had the assert included, however this could break
downstream users and it was opted to not add assert in the driver API
calls.
Update the documented example to reflect that.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
For the C sources the offloaded raw TX mode wasn't considered and else
case picks up system mode files causing build issues.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
- Adds 'supported: flash' to all NXP board .yaml
with enabled flash controller support.
- Sorts supported features alphabetically.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
Correctly selects the Kconfig symbols for viper CPU clusters
instead of having a reverse hwmv1 setup where the symbol has
a choice
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Add `se` variant to support the low-cost CoreS3 SE.
- Add configuration files
Add `m5stack_cores3_procpu_se(.dts|.yaml|defconfig)` files.
Reorganize dts files to split common parts.
- Update .yaml file
Add gpio, can, counter, entropy, pwm, and pinmux to the supported
feature group. Remove the `ignore_tags:` section.
- Update documents
Add and modify information about CoreS3 SE.
Add more description about sysbuild.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Disable the IPC communication between the domains
for the arm_thread_swap test since it is not needed
and it causes a flash oveflow for the no opmitization
test case.
Signed-off-by: Georgios Vasilakis <georgios.vasilakis@nordicsemi.no>
Enable the cpusec IPC and the bellboard nodes for
the nrf54h20dk cpuapp and cpurad targets to enable
communication between domains.
Also enables the region cpurad_ram0x_region since
it is also required for the communication.
Signed-off-by: Georgios Vasilakis <georgios.vasilakis@nordicsemi.no>
For the inverted pulse measurements, that should reflect
the duty-cycle off interval, the 1% deviation in test_capture
should be adjusted so it reflects duty-cycle off.
Signed-off-by: Ioannis Karachalios <ioannis.karachalios.px@renesas.com>
As per the PWM API definition, -EBUSY should be returned
when pwm_enable_capture is called and capturing
is already enabled. This commit deals with adding
a ztest_suite_before_t function that should disable
capturing at the end of a single test. Some tests, though,
such as test_pulse_capture, execute two sub-tests
and so, capturing is disabled in between. In fact, the omission
of pwm_disable_capture should not only result in aborting
a single test, but it can also raise system exception
due to invalid context. This is the case for
z_impl_pwm_capture_cycles where z_pwm_capture_cycles_callback
can be fired whilst the routine has already aborted and so
struct z_pwm_capture_cb_data data, defined within function
declaration, should not longer be valid.
Signed-off-by: Ioannis Karachalios <ioannis.karachalios.px@renesas.com>
It is recommended to record the subunit type itself instead of the
subunit ID when validating the transaction. This approach is more
meaningful and less prone to misinterpretation.
Signed-off-by: Zihao Gao <gaozihao@xiaomi.com>
check if multiples UART instances with same irq are enabled
at same time then enable shared_interrupt handler.
set the default value of SHARED_IRQ_MAX_NUM_CLIENTS config if
we have more than 2 usarts instances enabled.
Signed-off-by: Fabrice DJIATSA <fabrice.djiatsa-ext@st.com>
Update the instructions for the three possible Bluetooth setups
(controller-only, combined build, host-only) to be in line with how the
features are actually enabled (e.g. device tree for the controller and HCI
drivers).
Signed-off-by: Johan Hedberg <johan.hedberg@silabs.com>
Deprecate BT_CTLR, and add a new HAS_BT_CTLR as a virtual option which
specific users (like BT_LL_SW_SPLIT) select. This also means that we can
remove all places that were forcefully enabling the BT_CTLR option, and
instead we now depend on devicetree to get some local LL HCI driver
enabled which in turn also enables the HAS_BT_CTLR option.
Signed-off-by: Johan Hedberg <johan.hedberg@silabs.com>
Change running baudrate from `115200` from `3000000`.
Implement the function `bt_h4_vnd_setup` to update the HCI bandrate.
Add Kconfig `BT_H4_NXP_CTLR_WAIT_TIME_AFTER_BAUDRATE_UPDATE` to set
the waiting time after the controller bandrate HCI vendor specific
command sent. It is used to ensure the controller is ready to update
HCI bandrate.
Select `BT_HCI_SETUP` if `BT_H4_NXP_CTLR` is enabled.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
Added hw_mode check of AP with hostapd when getting link mode of current
station. If the hw_mode of AP is 11b, then the link mode of current
station will show 11b.
Signed-off-by: Hui Bai <hui.bai@nxp.com>
