Re-running the script that checks for the const qualifier missing on
struct device ISR's parameter.
The script also changes the parameter 'arg' to 'dev' when relevant.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Move the can_set_bitrate() function to can_common.c as it is getting
quite long for a static inline function.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add support for getting the maximum supported bitrate in bits/s for CAN
controller/transceiver combination and check that a requested bitrate is
within the supported range.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Only call the state change callback if the state has changed. Reuse the
existing function for retrieving the CAN controller state instead of
having the same code twice.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
According to Kconfig guidelines, boolean prompts must not start with
"Enable...". The following command has been used to automate the changes
in this patch:
sed -i "s/bool \"[Ee]nables\? \(\w\)/bool \"\U\1/g" **/Kconfig*
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Fix build break introduced in 03ab730347:
/zephyr/drivers/can/can_mcp2515.c:871:55: error: 'const struct
mcp2515_config' has no member named 'int_pin'; did you mean 'int_gpio'?
871 | LOG_ERR("Unable to configure GPIO pin %u", dev_cfg->int_pin);
/zephyr/drivers/can/can_mcp2515.c:942:14: error: 'GPIO_DT_SPEC_INST_GET'
undeclared here (not in a function)
942 | .int_gpio = GPIO_DT_SPEC_INST_GET(0),
| ^~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Add CAN controller device statistics support.
Initially the following per-device statistics are supported:
- Dominant bit transmission errors
- Recessive bit transmission errors
- Bit stuffing errors
- CRC errors
- Format errors
- Acknowledge errors
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Stop using redundant DEV_DATA/DEV_CFG macros and use dev->data and
dev->config instead.
Follows #41918.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
Reduce the number of TX buffers in use on the MCP2515 from 3 to 1 in
order to avoid CAN frame priority inversion.
The MCP2515 is unable to do internal TX frame arbitration based on the
CAN-ID of the frame. Priority must be set per TX buffer and the priority
cannot be rewritten unless the frame transmission is aborted.
Fixes: #26541
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Switch the Bosch M_CAN driver from TX FIFO mode to TX Queue mode in
order to avoid priority inversion of CAN frames.
Fixes: #26541
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Set enable configuration change bit in can_mcan_set_timing() because
the NBTP register can only be changed if we're in init mode AND
configuration change bit is set, per MCU docs.
Signed-off-by: Jeremy Wood <jeremy@bcdevices.com>
The CAN_BUS_UNKNOWN CAN controller state is only used to indicate that
the current CAN controller state could not be read.
Remove it and change the signature of the can_get_state() API function
to return an integer indicating success or failure.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
* New m_can driver variant for STM32H7, as it uses the complete m_can
register set.
* Fix definitions for CAN_MCAN_RXF0S_F0FL, CAN_MCAN_TXEFC_EFSA_POS.
Signed-off-by: Jeremy Wood <jeremy@bcdevices.com>
Stop using redundant DEV_DATA/DEV_CFG macros and use dev->data and
dev->config instead.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Remove the unused NUM_TX_EVENT_FIFO_ELEMENTS helper macro. There is no
dts property for setting the TX event FIFO size.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Rework the transmit error handling in the NXP MCUX FlexCAN driver:
- Frame transmission must be automatically retried in case of lost
arbitration or missing acknowledge.
- Abort any pending TX frames when bus-off state is entered.
- Fail early in can_send() if in bus-off state.
Fixes: #19502
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add support for disabling automatic retransmission of CAN frames
(similar to CAN "one-shot" mode in the Linux kernel).
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add optional user data argument to can_set_state_change_callback() to
comply with Zephyr API design guidelines.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
