Imported mem pool quota files from the SDK driver
Adding mempool quota files significantly improved
the performance of the SDK driver.While the basic
buffer pool caused issues during long running UDP
data transfers,the mempool quota demonstrated
stable and reliable performance.
Signed-off-by: Rahul Gurram <rahul.gurram@silabs.com>
Silabs siwx91x includes a memory controller for (Quad-)SPI PSRAM. It
allows the application to use the PSRAM as if it was any other RAM.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Honor Kconfig option `BT_CTLR_TX_PWR_ANTENNA` for limiting the maximum TX
power. The default value for this option is 0 dBm, which means that after
this change the actual TX power is likely lower than before, unless
increased by this option.
Signed-off-by: Kalle Kietäväinen <kalle.kietavainen@silabs.com>
Update Cmake to include hal EMDRV header
It also adds dmadrv source when CONFIG_SOC_GECKO_LDMA is selected
Signed-off-by: Martin Hoff <martin.hoff@silabs.com>
This driver allow to use Zephyr native IP stack or the IP stack provided
by HAL / WiseConnect.
The WiseConnect implementation may take advantage of the specific
features provided by the 917 (power consumption, speed,
validation...).
Some notable features are not available with this interface:
- It seems Zephyr does not provide API to offload multicast membership
management. User should be to directly call WiseConnect APIs
- Support for ICMP frames is difficult. Note that WiseConnect
automatically answer to ping request. It is just not possible to
send ping requests and receive ping responses.
- Zephyr and WiseConnect both support TLS offloading. However this
patch does not implement it.
- Reentrancy in the WiseConnect side is uncertain.
This implementation has been tested with samples/net/wifi/ (which relies
on subsys/net/lib/shell).
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Driver was tested with a custom application which enabled the BT_SHELL.
Basic functionalities were verified:
- Scanning
- Advertising
- Connecting
Configuration needed for the test:
- CONFIG_BT=y
- CONFIG_BT_PERIPHERAL=y
- CONFIG_BT_CENTRAL=y
- CONFIG_BT_SHELL=y
- CONFIG_SHELL=y
Co-authored-by: Tibor Laczko <tibor.laczko@silabs.com>
Signed-off-by: Tibor Laczko <tibor.laczko@silabs.com>
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Network Processor (NWP) is used to run WiFi, Bluetooth and Flash
drivers.
Co-authored-by: Tibor Laczko <tibor.laczko@silabs.com>
Signed-off-by: Tibor Laczko <tibor.laczko@silabs.com>
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Implement DMA driver for siwx917 using UDMA peripheral. For now,
Scatter/Gather DMA is not yet supported.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Support for random number generator is required for most of the
cryptographic operations, including support for WiFi and TLS.
This driver has been tested with tests/drivers/entropy:
*** Booting Zephyr OS build v3.7.0-4339-g1ec5ce05f9f8 ***
Running TESTSUITE entropy_api
===================================================================
START - test_entropy_get_entropy
random device is 0x8217298, name is rng@45090000
0x93
0x3e
0xf1
0x68
0xd4
0x22
0xbf
0x4d
0xad
PASS - test_entropy_get_entropy in 0.012 seconds
===================================================================
TESTSUITE entropy_api succeeded
------ TESTSUITE SUMMARY START ------
SUITE PASS - 100.00% [entropy_api]: pass = 1, fail = 0, skip = 0 ...
- PASS - [entropy_api.test_entropy_get_entropy] duration = 0.01 ...
------ TESTSUITE SUMMARY END ------
===================================================================
RunID: d1547c805699201af769cb01331efcce
PROJECT EXECUTION SUCCESSFUL
Co-authored-by: Tibor Laczko <tibor.laczko@silabs.com>
Signed-off-by: Tibor Laczko <tibor.laczko@silabs.com>
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Propagate device tree configuration for the power amplifier to
the HAL configuration header.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
When the SiSDK HAL was introduced, a corresponding Kconfig option
was not. Update Series 2 SoCs to use the new option.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
This enables silabs series 2 hal source files for the silabs
acmp module to be compiled when the SOC_SILABS_ACMP
configuration is selected.
Signed-off-by: Christian Galante <christian.galante@silabs.com>
Add a Kconfig option which can be used to enable vendor HCI extensions for
Silicon Labs EFR32 devices.
Signed-off-by: Johan Hedberg <johan.hedberg@silabs.com>
Add empty function stubs to support building with the newly introduced
CONFIG_BUILD_ONLY_NO_BLOBS option.
Signed-off-by: Johan Hedberg <johan.hedberg@silabs.com>
Only initialize the HFXO Manager HAL driver if the HFXO is enabled in
DeviceTree, the device uses SYSRTC for timekeeping, and Power Manager
is enabled. HFXO Manager integrates with the Sleeptimer HAL driver for
SYSRTC to autonomously wake the HFXO prior to Sleeptimer wakeup from
deep sleep. It is not needed on devices that don't have HFXO-SYSRTC
integration, and it is not needed if the application doesn't use deep
sleep.
Add missing call to init_hardware() prior to init().
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
Add OS timer implementation making use of the Sleeptimer HAL.
Sleeptimer integrates tightly with the Silabs Power Manager HAL,
and must be used as the OS timer to achieve optimal power consumption
when using the radio.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
CMSIS SystemInit is not used in Zephyr. Implement the functionality
that isn't already done by Zephyr startup using soc_prep_hook().
The reason the lack of TrustZone init did not create immediately obvious
issues previously is that SMU faults can only happen if the SMU clock is
enabled.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
Rename the Silabs HCI driver to hci_silabs_efr32.c to better indicate what
hardware it supports. Also rename the associated devicetree binding and
Kconfig options to be consistent with the new driver name.
Signed-off-by: Johan Hedberg <johan.hedberg@silabs.com>
Swap from the deprecated device_init_* functions to clock manager
for clock tree configuration. Populate config headers using
device tree representation of clock tree and oscillator config.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
The DC-DC converter was unconditionally initialized with default
settings on Series 2. Add device tree binding and nodes, and guard
call to init function. Map DT options to config header from HAL.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
Move the CMakeLists.txt and Kconfig files from the hal_silabs tree under
modules/hal_silabs in the main tree. This also includes all Zephyr shim
code from the hal_silabs tree.
Signed-off-by: Johan Hedberg <johan.hedberg@silabs.com>
