Initial integration with renode-test was introduced in commit bdf02ff,
which added support for calling the `renode-test` command from both west
and twister.
This commit removes the custom run_renode_test target used for running
Robot tests with the `west build` command and makes twister call
`renode-test` directly instead.
Signed-off-by: Michał Szprejda <mszprejda@antmicro.com>
This commits add the BLEIF instance which is compatible with
"ambiq,spi-bleif" on Ambiq apollo3p_evb and apollo3_evb.
Also creates the default pinctrl for the defined instance.
Signed-off-by: Aaron Ye <aye@ambiq.com>
The RTC subsystem in espressif's SOCs, among other tasks
is responsible for clock selection for CPU and for low
power domain clocks such as RTC_SLOW and RTC_FAST.
This commit allows for proper clock source and rate
selection for CPU, using the espressif,riscv and
espressif,xtensa-lx6/7 bindings.
It also enables clock selection for RTC_FAST and RTC_SLOW,
that impacts some peripherals, such as rtc_timer.
Signed-off-by: Lucas Tamborrino <lucas.tamborrino@espressif.com>
- Add pinctrl for flexcomm0 in usart mode
needed for BLE tester application
- Reserve the firmware storage partition
- Mark HCI as a wakeup source
Signed-off-by: Yassine El Aissaoui <yassine.elaissaoui@nxp.com>
- Add initial version of CYW920829M2EVK-02 board
- [drivers: clock_control] Make it possible to set up both iho and imo
clocks instead of just one or the other
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
Refactor the 54L board file to be able to better support out-of-tree
non-secure boards.
This aligns better with nrf53's DT.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
In order to avoid defining almost the same overlays in the available
sample codes, tests and user applications, a common overlay file
per memory type is demonstrated under the boards dts folder.
Currently only the PSRAM interface is supported and the APS6404L
PSRAM QSPI memory device is demonstrated. In doing so, an
application code will only have to define another overlay file explicitly,
under application's board folder, to overwrite the default QSPI
controller's settings. In either case, users should explicitly
invoke the requested overlay files at 'west build' invokation
via the DTC_OVERLAY_FILE system variable.
Signed-off-by: Ioannis Karachalios <ioannis.karachalios.px@renesas.com>
Added initial board support for the
frdm_ke15z board.
Signed-off-by: Emilio Benavente <emilio.benavente@nxp.com>
Signed-off-by: Pavel Krenek <pavel.krenek@nxp.com>
Two pins assigned to SPI controller (P0_22,P0_23) are dedicated
to XTAL32K which is present on devkit.
For this reason SPI function are re-assigned to pins available
on optional header MikorBUS 1 to match configuration of SPI2
which is routed to MikorBUS 2 header.
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
This board HW models now include the RRAMC, FICR and UICR.
Let's update the docs accordingly.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
The RRAMC is now supported by the HW models.
Let's enable the RRAM controller, and
add a storage partition definition which
tests and samples can use by default.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
With the introduction of the new Hardware model, we now have an easy
method to describe variants of boards. This is especially helpful for
Microchip's PolarFire SoC Icicle Kit which has a heterogeneous
core-complex. Introduce an SMP capable variant with four SMP capable
harts for the SMP cluster and disables the e51 monitor hart
Signed-off-by: Conor Paxton <conor.paxton@microchip.com>
This commit adds support for the I2C which
can be found in Apollo3 SoCs, it can work in
both DMA and non-DMA modes
Signed-off-by: Hao Luo <hluo@ambiq.com>
Convert the ST7735R display to use the MIPI DBI API. Boards and overlays
using this display are also updated.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add support for the goworld 16880 display module. As this display module
only features an FFC cable, it is added as a board overlay for the RW612
BGA. This module uses an ST7796S display controller as well as an FT7401
touch controller (which is managed by the FT5336 input driver)
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This fixes the SPI DTS bug on the nrf5340_audio_dk board
which was introduced by b8978e9:
unit address and first address in 'reg' (0x0) don't match
for /soc/peripheral@50000000/spi@a000/sdhc@1
unit address and first address in 'reg' (0x1) don't match
for /soc/peripheral@50000000/spi@a000/cs47l63@2
Signed-off-by: Tim Sørensen <tims@demant.com>
With this configuration of the device tree, we use 80 MHz as
a FDCAN bus clock. This configuration allows to pass the tests.
Signed-off-by: Tomáš Juřena <jurenatomas@gmail.com>
After recent HWv2 model changes there is defconfig file
broken, so we got incorrect platform configuration. Fix that.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Evgeniy Paltsev <PaltsevEvgeniy@gmail.com>
This adds DT aliases for LED and button used in recovery mode of the
MCUboot bootloader, on the 'nucleo_wba55cg' board.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This board includes three gpio-connected LEDs and push-buttons. Include
all missing defines in board's DTS and while at it, fix existing button
definition (missing pull-up enable) and align node names with other
boards (e.g. 'nucleo_wb55rg').
Provided changes were tested on real board with 'blinky' and 'button'
samples.
Additionally, duplicated LED nodes no longer required were removed from
overlay file for this board, in 'suspend_to_ram' sample.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
