Add support for disabling automatic retransmission of CAN frames
(similar to CAN "one-shot" mode in the Linux kernel).
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Pin controller address is the same for all member of the
GEN3 SoC Series, but pinmux configuration is SoC specific.
Signed-off-by: Julien Massot <julien.massot@iot.bzh>
Renesas R-Car series contains a PFC (Pin Function Controller).
This module consists of registers for selecting the function of
the multiplexed pins and controls the pull-up resistor on each pin.
Signed-off-by: Julien Massot <julien.massot@iot.bzh>
Remove the unused base binding for CAN bus devices (as in devices
present on a CAN bus). This binding should have been removed in
2269408572
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
On some platforms, HPET is not wired to trigger IRQ 2.
This would make HPET non-functional if the legacy
interrupt routing bit is set in the global config
register. This adds a DTS flag so the driver won't
set the bit to enable legacy interrupt.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Fix the interrupt setting in the fvp_baser_aemv8r dts:
- The correct interrupt number is 5, not 0.
- The interrupt priority and type are swapped.
This patch also enables interrupt driven mode for this platform as this
is the ideal setting for a Fast Models based platform.
Issue-ID: SCM-4037
Signed-off-by: Filipe Rinaldi <filipe.rinaldi@arm.com>
Change-Id: Ic4815f5afe4c9df9d8fe373d47d2773d64087c96
dts/bindings/timer/riscv,machine-timer must have compatible name
riscv,machine-timer. nuclei,machine-timer is wrong, correct it.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
This PR adds the different handling of temperature sensor for the
STM32L5 soc. In this soc, there are some calibration settings which
need to be applied for temperature conversion.
Signed-off-by: Wouter Cappelle <wouter.cappelle@crodeon.com>
The dts binding general rules document states that the property
description should explain why the default value was selected
(e.g. "default is the value at power-on").
See comment in #41143
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add fragment:
io-channel-cells:
- input
to binding of the "ite,it8xxx2-adc" and "zephyr,adc-emul" compatible.
It is necessary to use io-channels property.
Signed-off-by: Dawid Niedzwiecki <dn@semihalf.com>
Certain stm32 soc's have a single shared irq for all adc channels
on those soc's only a single channel is supported.
Added a Kconfig that enables a shared irq for stm32f2x, stm32f4x,
stm32f7x soc's. The shared IRQ uses a flag to limit the number of
interrupts defined to only 1. A shared irq handler is added which
determines which ADC instance the interrupt is for, it then calls
into the existing interrupt.
Signed-off-by: Marius Scholtz <mariuss@ricelectronics.com>
The default I2C channel 3 is used by alternate function of GPIO H1/H2
Krabby uses GPIO F2/F3 as I2C channel 3, so we need to add the
compatibility of the GPIO F2/F3.
TEST=test on it8xxx2_evb:
zmake configure -b zephyr/projects/it8xxx2_evb/
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
An additional devicetree poperty `single-wire` is added
to uart and usart bindings of stm32. The driver checks this value
during initialization and enables the single wire mode when set.
Signed-off-by: Jonathan Hahn <Jonathan.Hahn@t-online.de>
The leon3 SoCs were missing definitions of the CPU node. This node is
now required for PM, so that power states can be defined.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Better setting a default value there so DT_PROP() will return something
relevant whether the property is set or not.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Add timer and pwm nodes. The structure follows a similar approach to the
one used by STM32. Timer nodes store all timer information (e.g.
pre-scaler), whereas the pwm nodes are children of the timer node
indicating a specialization of the multiple timer functionalities.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Add timer and pwm nodes. The structure follows a similar approach to the
one used by STM32. Timer nodes store all timer information (e.g.
pre-scaler), whereas the pwm nodes are children of the timer node
indicating a specialization of the multiple timer functionalities.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
HSE clock frequency value depends on target.
It can't be defaulted.
Remove this property to ensure it is set properly for each target.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
NPCX7/9 has a different ADC register structure. NPCX7 has 3 threshold
detectors from offset 0x14 & has 10 input channels. NPCX9 has 6
threshold detectors from offset 0x60 & has 12 input channels.
This commit fixes the NPCX ADC register structure.
Signed-off-by: Wealian Liao <WHLIAO@nuvoton.com>
Kconfig options will anyway enable/disable the driver relevantly.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Assign unique memory-region attribute values for both OCM
memory areas so that the lower region starting at address 0
is identified as OCM_LOW, while the alternate location for
the OCM memory is identified as OCM_HIGH.
The updated linker command file will use those identifiers
for OCM section mapping based on which of the two OCM areas
is marked as 'chosen' at the board level.
Signed-off-by: Immo Birnbaum <Immo.Birnbaum@weidmueller.com>
YAML description file for the On-Chip Memory of the Xilinx
Zynq-7000, DT identifier "xlnx,zynq-ocm".
Signed-off-by: Immo Birnbaum <Immo.Birnbaum@weidmueller.com>
- The gpio dt-bindings were not included
- gpio-controller property was not present in gpio nodes
- number of gpio cells was not present in gpio nodes
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
- The gpio dt-bindings were not included
- gpio-controller property was not present in gpio nodes
- number of gpio cells was not present in gpio nodes
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Add DT node for EXTI (External Interrupt Controller). Only line
interrupts added for now (used for GPIO interrupts).
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Add DT node for EXTI (External Interrupt Controller). Only line
interrupts added for now (used for GPIO interrupts).
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
The spi-bus-width property provides information if the target system
has all SIO[0123] pins connected to NOR flash memory.
It must be equal to 4 to enable QSPI 4 IO operation.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Some flash memories connected to QUADSPI IP block on stm32[fh]7 devices
require proper reset pulse before configuration.
This patch adds two new properties - the 'reset-gpios' phandle,
which allows specifying GPIO pin for RESETn pulse and
'reset-gpios-duration', which provides the time (in ms) for reset
duration.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
