Removes duplicate code and inconsistencies in the naming of the
cc13xx_cc26xx devicetree and RTC driver hierarchy and alignes it with
the actual TI product series naming hierarchy.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
Adds PHY driver. Works via MDIO API and
exposed ADIN2111 MDIO Clause 45
functions.
Link status detection is triggered by
ADIN2111 driver within offloaded IRQ
handler.
Supports:
- LED0, LED1 enable/disable
- Fatal HW error detection
- AN 2.4V tx mode enable/disable
The initialization order is important.
PHY 2 must be initialized after PHY1.
Therefore, it shall be defined after the 1st one
in the devicetree.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Adds MDIO driver. Works via exposed
ADIN2111 functions.
It is possible to access Clause 45 and 22 registers.
Due to MDIO API limitation Clause 45 access
is done using driver specific MDIO functions.
Provides API and functions for PHY driver.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Adds initial ADIN2111 2-Port 10BASE-T1L (SPE)
switch support. Works over SPI.
The driver creates 2 interfaces, 1 per port (PHY).
Configures multicast and broadcast filters.
The same unicast is applied to both ports.
Supports:
- Link state detection
- CRC enable/disable
- Ports config set
- Ports ETH stats
Provides functions for MDIO driver.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
The mcumgr subsystem as a whole is already maintained by @nordicjm
(#57780) and I am no longer actively using mcumgr, so removing myself
from the equation and letting more capable hands take over.
Signed-off-by: Mikkel Jakobsen <mikkel.aunsbjerg@escolifesciences.com>
This driver implement basic functions of ili9342c controller
which comes mostly with IPS displays.
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
With significant contribution to MCUmgr that brought increased
upload speeds and various other improvements in RAM and CPU usage,
general improvements in MCUmgr architecture and documentation,
Jamie has shown his vision for the subsystem and therefore
lets welcome him as a new MCUmgr subsystem maintainer.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Bsim won't be limited anymore to BT tests.
In preparation for adding more tests in network areas
swap the tests/bluetooth/bsim with tests/bsim/bluetooth
There is no other changes in this commit beyond that.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
- Add Ian Fyall (@ifyall) as codeowner for Infineon/Cypress sources.
- Add Nazar Palamar (@npal-cy) as codeowner for Infineon/Cypress sources.
- Remove Gerson Fernando Budke (@nandojve) from codeowner
of Cypress sources.
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
The Host Commands can be used with different transport layers e.g. SHI
or eSPI. The code that provides the peripheral API and allows sending
and receiving Host Commands via different transport layers is not
actually drivers of a peripheral, so move it to the
subsys/mgmt/ec_host_cmd folder.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
This commit separates each test by layer level.
Obviously the tests will run the whole stack, but they should be separated
by which component/layer they intend on testing.
Signed-off-by: Jonathan Rico <jonathan.rico@nordicsemi.no>
Add myself as a maintainer for existing TI platforms,
currently I am an employee with Texas Instruments Inc. in
the Embedded Processors software department and has worked
on the supported simplelink platforms in Zephyr for the last
2 years.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
This commit adds a CODEOWNERS entry for the C++ library (previously
called C++ subsystem) to appease the check_compliance.py.
Note that we have not completely phased out the CODEOWNERS file yet
and, until we do, the CODEOWNERS check in check_compliance.py should
stay.
Signed-off-by: Stephanos Ioannidis <stephanos.ioannidis@nordicsemi.no>
This commit adds support for Silicon Labs EFR32BG22 SoC.
Co-authored-by: Mateusz Sierszulski <msierszulski@antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
Introduce an API mirroring the CMSIS-DSP's basicmath. If CMSIS_DSP is
enabled, then it will by default be used as a backend. Developers may
opt into a custom backend by setting CONFIG_DSP_BACKEND_CMSIS=n. If
done, the application must provide `zdsp_backend/dsp.h` and optionally
implement the functions in its own .c files.
Signed-off-by: Yuval Peress <peress@google.com>
Generates XML file containing VIF policies by reading the device tree
using EDT.pickle generated during build
This script writes a subset of general and sink-pdo VIF policies in
output file
This script gets invoked during build if enabled through kconfig
The generated XML containing USB-C VIF policies could be used by
USB PD/Type-C analysers/testers to understand USB-C properties and
perform tests accordingly
Signed-off-by: Madhurima Paruchuri <mparuchuri@google.com>
