bmi160.c module defines DT_DRV_COMPAT, but bmi160_trigger.c doesn't.
This causes a catastrophic chain of events.
The bmi160.c module includes bmi160.h,
in which the macro DT_ANY_INST_ON_BUS_STATUS_OKAY
affects the size of bmi160_bus union.
So bmi160.c defines a bmi160_cfg struct which contains that union.
Now, in bmi160_trigger_init we get a pointer to that config struct.
The fact that this module now includes bmi160.h without
DT_DRV_COMPAT, causes it to think the union is empty.
That doesn't cause compilation error, just undefined behaviour,
In which you address an empty struct fields.
In general, I suggest that someone makes sure it doesn't happen
in other drivers as well. The problem presented here is general,
meaning that if an h file assumes someone defined DT_DRV_COMPAT
before and it doesn't,
it may lead to some weird behaviour, like the one described.
Signed-off-by: Avi Green <avigreen1978@yandex.com>
According to Kconfig guidelines, boolean prompts must not start with
"Enable...". The following command has been used to automate the changes
in this patch:
sed -i "s/bool \"[Ee]nables\? \(\w\)/bool \"\U\1/g" **/Kconfig*
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
by default, a global trigger thread was enabled in kconfig but
the thread priority and stack size depended on a local thread
being enabled.
the local thread option was never used anywhere so it is removed.
Signed-off-by: Mikkel Jakobsen <mikkel.aunsbjerg@escolifesciences.com>
Allow movement detection to be used on hardware
that only has one interrupt line connected.
Change hardware configuration to a bitmask.
Signed-off-by: Andrew Hedin <andrew.hedin@lairdconnect.com>
sensor_value_from_double had a early overflow when converting the
fractional part (val2). This occured when input was more then
2147.493647 (inp >= INT32_MAX/1000000.0 + 0.01).
return value -ERANGE as this is what errno is set to by `strtod` and
similar posix functions.
fixes issue #39176
Signed-off-by: Simon Frank <simon.frank@lohmega.com>
This commit implements the temperature sensor interface for
the Maxim MAX31875Low-Power I2C Temperature Sensor.
Signed-off-by: Pete Dietl <petedietl@gmail.com>
`qdec_sam` driver supports currently only position measurement and does
not support reading of the index signal. Unfortunately, the index
signal was internally enabled in the driver. If the pin to which the
index signal was connected was used by another driver it could lead to
a false detection of the signal change. Detection of the index signal
change resets the position measurement.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This corrects the following:
1. The priority of type cast is lower than member access. So don't need
the redundant parentheses.
2. The macro should be added to the parentheses.
Signed-off-by: Wealian Liao <WHLIAO@nuvoton.com>
Some drivers explicitely casted data/config from void * to the
corresponding type. However, this is unnecessary and, in many drivers it
has been misused to drop const qualifier (refer to previous commits).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Replace all get_dev_data()/get_dev_config() accessor utilities with
dev->data and dev->config.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Stop using redundant DEV_DATA/DEV_CFG macros and use dev->data and
dev->config instead.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
In order to align with macros used to obtain a device reference (e.g.
DEVICE_DT_GET), align the PM macros to use "GET" instead of "REF". This
change should have low impact since no official release has gone out yet
with the "REF" macros.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This PR adds the different handling of temperature sensor for the
STM32L5 soc. In this soc, there are some calibration settings which
need to be applied for temperature conversion.
Signed-off-by: Wouter Cappelle <wouter.cappelle@crodeon.com>
moving the conversion from adc value to the get function
which will be used for different handling of stm32 temp sensors
Signed-off-by: Wouter Cappelle <wouter.cappelle@crodeon.com>
i2c_burst_write can have portability issues with certain i2c
peripherals that can fail when this api is called. This fixes the case
where this can be easily replaced with i2c_write in mcp230xx,
pca95xx, stmpe1600, max17055, and tmp112.
Signed-off-by: Ryan McClelland <ryanmcclelland@fb.com>
The function that sets the driver's state of the sensor's
config register has a bug. This commit fixes that.
Signed-off-by: Pete Dietl <petedietl@gmail.com>
Move odr and range properties for both accelerometer and gyro
from Kconfigs to Device Tree.
Fixes#41117
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This sample writes the tmp108 temperature to the console
once every 3 seconds. There are macro definitions included
for turning off and on alerts if that is set up, and
also using low power one shot mode.
Signed-off-by: Jimmy Johnson <catch22@fastmail.net>
Adding support for the TI TMP108 temperature sensor. This includes
over/under temp interrupt support as well as one shot, continuous
conversion and power down modes.
Signed-off-by: Jimmy Johnson <catch22@fastmail.net>
Create an explicit ina230 driver which is supposed to
work with 230 and 231 variants. While at it switch
to i2c_dt_spec helpers and change device-tree node
names to use - instead of _ in order to follow
convention.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
This commit aligns lps22hh sensor driver to latest multi
instance sensor driver model.
In particular it makes use of the stmemsc common routines
and move ctx handler inside struct config, so that the
bus_init routines can be totally avoided.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Make use of the i2c and spi DT APIs introduced in
2946a535 and c894ad12 that get i2c_dt_spec and spi_dt_spec
as input arguments.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The warning below appears once -Waddress-of-packed-mem is enabled:
/__w/zephyr/zephyr/drivers/sensor/bmi160/bmi160.c: In function
bmi160_gyr_channel_get:
/__w/zephyr/zephyr/drivers/sensor/bmi160/bmi160.c:795:23: error: taking
address of packed member of struct <anonymous> may result in an
unaligned pointer value [-Werror=address-of-packed-member]
795 | data->sample.gyr, val);
| ~~~~~~~~~~~~^~~~
/__w/zephyr/zephyr/drivers/sensor/bmi160/bmi160.c: In function
bmi160_acc_channel_get:
/__w/zephyr/zephyr/drivers/sensor/bmi160/bmi160.c:807:23: error: taking
address of packed member of struct <anonymous> may result in an
unaligned pointer value [-Werror=address-of-packed-member]
807 | data->sample.acc, val);
| ~~~~~~~~~~~~^~~~
To avoid the warning, make the struct non-packed, since it is not
necessary in this case given that a union already guarantees that the
pointer to the union points to each member of the union equally..
More info in #16587.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The original code erroneously used:
uint16_t *val;
sizeof val
instead of:
sizeof *val;
This commit fixes this problem and removes an unnecessary
buffer from the stack
Signed-off-by: Pete Dietl <petedietl@gmail.com>
Fixes: #40538
The TEMP_NRF5 setting requires MULTITHREADING, therefore add this
dependency to Kconfig.
The TEMP_NRF5 supports an alternative driver implementation using the
TEMP_NRF5_FORCE_ALT setting.
Because it cannot be known whether an alternative implementation has
the same dependency, then the MULTITHREADING is OR'ed with
TEMP_NRF5_FORCE_ALT, as to allow enabling of TEMP_NRF5 if an alternative
driver is provided.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Remove check if frequency is equal to zero. A value of `ODR = 0` is
explicitly allowed by manufacturer / datasheet.
This has prevented applications from using the lis2dh power-down-mode,
which is set via `ODR = 0`.
For reference see "Table 28. Data rate configuration" in datasheet p.33.
Fixes#35486.
Signed-off-by: Markus Brüx <markus.bruex@grandcentrix.net>
