Remove the `IS_BOOTLOADER` and `BOOTLOADER_SRAM_SIZE` symbols from the
`nucleo_l053r8` and `nucleo_l031k6` boards. The stated reason for
inclusion is to disable the RAM vector table, however this doesn't apply
to the STM32L0 series, only STM32F0.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Initialize `handle.device` to `None` so that the assert after the
matching has a chance to catch errors. Without this, a failed match will
raise an exception on the line above as it attempts to get a property
that doesn't exist.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Document the fact than NVS image of different wbs
are compatible each other if psychical ATE size
is kept.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Signed-off-by: Damian Krolik <damian.krolik@nordicsemi.no>
When existing records stored in the NVS are not properly
aligned according to the current flash driver requirements,
fs->data_wra may be initialized with an unaligned address.
Fix the initialization code, so that fs->data_wra is rounded
up to the nearest multiple of the current flash driver block
size.
The situation may occur during a firmware upgrade which
introduces a new flash driver or changes its parameters.
Signed-off-by: Damian Krolik <damian.krolik@nordicsemi.no>
Remove undefined functions (unsued anymore).
Add missing stub implementation for new DF related radio functions.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
Add Radio configuration API that gives possiblity configure
reception and sampling of CTE.
Part of alrady implemented API was re-factored to comply
with new API and do complete initialization of registers:
DFECTRL1 and CTEINLINECONF.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
The network tests were expecting that network interfaces
are in certain order. As we cannot guarantee that, refactor
the tests like this:
* if test is using DUMMY L2 driver, then disable Ethernet L2
and fetch only DUMMY L2 instead of default interface
* if test is using Ethernet L2 driver, then make sure that the
test is using the Ethernet interface specified in the test
instead of the one provided by the DUT
Fixes#34505
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This adds the bits to the gen_mmu.py script so that extra mappings
can be added with caching disabled. This is useful for mapping
MMIO regions where caching is not desired.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This commit enables flash support for stm32h747i_disco_m7
in device tree. This has been tested with flash sample
application on stm32h747i_disco platform with m7 core.
Flash is shared between two cores (M4 & M7) so the last 1M is
assigned to M4 core. Hence allocating 1M of storage at the
end of first 1M.
Signed-off-by: Krishna Mohan Dani <krishnamohan.d@hcl.com>
There is a possibility that the DWT frequency calculation
is divided by zero. So this fixes the issue by repeatedly
trying to get the delta clock cycles and delta DWT cycles
until they both are not zero.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
There is a possibility that the TSC frequency calculation
is divided by zero. So this fixes the issue by repeatedly
trying to get the delta clock cycles and delta TSC cycles
until they both are not zero.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The use of device_pm_control_nop is deprecated so remove it
from the test as it will give warning in CI.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add binding fro stm32wl-rcc.yaml that derivates from stm32wb-rcc.
Additionally update stm32wb-pll-clock.yaml to be used as well
for stm32wl series and add missing div-m property.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add support for STM32L0 clocks bindings.
Also, add a small tweak to SYSCLK selection to factorize some lines.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add clocks node and clocks to stm32l5 series.
PLL binding is reused from stm32l4 series.
Matching binding is updated to document that.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add clocks nodes for F0/F3/G0/G4 series.
For F0 and G0 series, update compatible for rcc node
to specify use of dedicated "st,stm32f0-rcc" compatible.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add bindings for F0/F3/G0/G4 clocks.
Introduce new rcc binding "st,stm32f0-rcc" binding
that describes RCC hardware blocks that don't have
"apb2-prescaler".
This binding also applies to G0.
Binding "st,stm32f0-pll-clock" is used for both F0
and F3 series.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add PLL bindings for STM32F1 devices.
- Main PLL binding for STM32F1 non connectivity lines
- Main and PLL2 binding for Connectivity lines (F105/F107)
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
To allow transition to device tree based clock configuration on
stm32 targets, rework clock_control driver to use intermediate
STM32_ macros initially defined as the equivalent Kconfig macros
for now.
Propagate the change in all code using these macros.
The reason to introduce these new macros instead of configuring
Kconfig flags using dt kconfigfunctions is that we'll need
to be able to inform users that Kconfig flags are deprecated
once the whole family conversion is done, to encourage
out of tree users to adopt this new configuration scheme.
Note: For now STM32H7 series and code is excluded.
This is the same for some series specific code such as
PLL mul/div for L0/L1 and XTRE prescaler on F1 series.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add configurable attached event delay. Delay can be used to give
USB Charging Controller time for initialization.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Logging failed to compile when --no-gc-sections is used because
log_core is conditionally calling mpsc_pbuf.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
When PROVISIONER and CDB is enabled then IUT couldn't be a NODE.
This patch fixes this by not returning an error when CDB is not
configured. This is useful especially in testing environment, when all
the features are compiled in and we can choose role in runtime.
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
Add support for u-blox EVK-NINA-B4, which uses the nRF52833
This board is similar to the nrf52833dk_nrf52833, though it
uses a u-blox NINA-B40x openCPU module with DC-DC support
included.
Simplified pwm LED aliases
Corrected LED assignments for red, green, and blue
Addressed review comments (spi & gpio 0 0)
Tested with blinky, button, and Bluetooth peripheral_hr
Signed-off-by: Bob Recny <bob.recny@u-blox.com>
Since the API already has a function to create an LwM2M object instance,
it makes sense to add a corresponding delete funtion, allowing the
application to delete created objects.
Additionally, for the remote delete set the Registration Update trigger
only when not in bootstrap mode.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The Registration Update message should be sent whenever an object
instance is created or deleted. Currently this was only the case when an
object instance was created by the server and not by the application.
Fix this by triggerng the Registration Update from the API function
as well.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
