Stop using redundant DEV_DATA/DEV_CFG macros and use dev->data and
dev->config instead.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
fix uart_sam0_irq_update to only clear the RXS bit by writing only the
RXS bitflag to the INTFLAG register. Performing an |= opperation
with the bitflag for RXS incorrectly clears all pending interrupts set
since writing 1 to a INTFLAG clears that bit field. This causes a race
condition on when TXC will be cleared before all bytes have finished
being clocked out on tx and TXC being set 1 again. If tx finishes first,
any driver using uart_irq_tx_complete will deadlock the system.
Signed-off-by: Ron Smith <rockyowl171@gmail.com>
sam0 does not currently have a uart_irq_tx_complete method for interrupt
driven mode.
This is especially important since the sam0 platform has seperate
interrupt signals for TX data register empty and TX complete therefore
the TX register being empty does not nessisarily mean the data has been
shifted out.
Drivers should check uart_irq_tx_complete if it needs to guarantee
that the data has been fully transmitted in a hardware agnostic way.
Signed-off-by: Ron Smith <rockyowl171@gmail.com>
Refactors all of the serial drivers to use a shared driver class
initialization priority configuration, CONFIG_SERIAL_INIT_PRIORITY, to
allow configuring serial drivers separately from other devices. This is
similar to other driver classes like I2C and SPI.
The default is set to CONFIG_KERNEL_INIT_PRIORITY_DEVICE to preserve the
existing default initialization priority for most drivers. The one
exception is uart_lpc11u6x.c which previously used
CONFIG_KERNEL_INIT_PRIORITY_OBJECTS.
This change was motivated by an issue on the frdm_k64f board where the
serial driver was incorrectly initialized before the clock control
driver.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Updated uart_rx_enable() and uart_tx() to use timeout given
in microseconds. Previously argument was given in milliseconds.
However, there are cases when milliseconds granularity is not
enough and can significantly reduce a throughput, e.g. 1ms is
100 bytes at 1Mb.
Updated 4 drivers which implement asynchronous API. Updated
places where API was used.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
uart_sam0_dma_tx_done callback triggers when the last byte
is transferred from the tx sram buffer to the sercom DATA register.
However the byte has yet to be transmitted completely which can lead to
incorrect event handling if UART_TX_DONE is expected to signal
the end of transmission.
Signed-off-by: Ron Smith <rockyowl171@gmail.com>
Fixes a compile error for the err_check function not being found if
if CONFIG_UART_INTERRUPT_DRIVEN is not enabled.
Signed-off-by: Ron Smith <rockyowl171@gmail.com>
Fixes the issue where uart_sam0_irq_tx_ready would return true if
the INTFLAG was set even though the INTSET bit for the given
interrupt was not enabled yet through uart_sam0_irq_tx_enable.
Signed-off-by: Ron Smith <rockyowl171@gmail.com>
Add Atmel sam0 sercom[uart] pinctrl bindings and implements pinctrl at
driver level. It changes all sam0 boards to use new feature and remove
pinmux driver dependency for sercom[uart]. The samples that require a
binding were update to keep consistency and avoid errors.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This kconfig option enables runtime configuration of UART
controllers. This allows application to call uart_configure()
to configure the UART controllers and calling uart_config_get()
to retrieve configuration. If this is disabled, UART controllers
rely on UART driver's initialization function to properly
configure the controller. The main use of this option is mainly
code size reduction.
Fixes#16231
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Automatic collision detection for half-duplex mode can be enabled
by setting `collision-detection` proprety for uart hardware
in the dts file. If the transmitted bit does not match the received
bit an error is raised. This is useful in RS-485 half-duplex mode.
Signed-off-by: Arvin Farahmand <arvinf@ip-logix.com>
Replace all existing deprecated API with the recommended alternative.
Fixes#34102
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
These are all the case that coccinelle cannot find as they are inside
macro declarations.
Fixed via:
git grep -rlz -E "\(struct device \*" |
xargs -0 sed -i 's/(struct device/(const struct device/g'
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Modified order of reported events on rx disable to match API
description: first RX_RDY and then RX_BUF_RELEASED.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Usually, we want to operate only on "available" device
nodes ("available" means "status is okay and a matching binding is
found"), but that's not true in all cases.
Sometimes we want to operate on special nodes without matching
bindings, such as those describing memory.
To handle the distinction, change various additional devicetree APIs
making it clear that they operate only on available device nodes,
adjusting gen_defines and devicetree.h implementation details
accordingly:
- emit macros for all existing nodes in gen_defines.py, regardless
of status or matching binding
- rename DT_NUM_INST to DT_NUM_INST_STATUS_OKAY
- rename DT_NODE_HAS_COMPAT to DT_NODE_HAS_COMPAT_STATUS_OKAY
- rename DT_INST_FOREACH to DT_INST_FOREACH_STATUS_OKAY
- rename DT_ANY_INST_ON_BUS to DT_ANY_INST_ON_BUS_STATUS_OKAY
- rewrite DT_HAS_NODE_STATUS_OKAY in terms of a new DT_NODE_HAS_STATUS
- resurrect DT_HAS_NODE in the form of DT_NODE_EXISTS
- remove DT_COMPAT_ON_BUS as a public API
- use the new default_prop_types edtlib parameter
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The conversion in 9b096f40b6 left out a
few tidbits that were not converted properly. Complete the conversion
properly.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Convert to using DT_INST_LABEL() in the dma driver and convert dma users
to use the DMA property macros to get the dma controller name. We make
the assumption in the drivers that there is a single DMA controller
instance.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rework the devicetree to utilize new DT_INST macros and extract per
instance data for clocks and dma from devicetree. We update the
atmel,sam0-uart binding for dma to replace the rxdma and txdma
properties with proper 'dmas' property.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
When we build this driver with CONFIG_UART_ASYNC_API enabled we get the
following build error:
uart_sam0.c: In function 'uart_sam0_init':
uart_sam0.c:558:35: error: redefinition of 'dev_data'
558 | struct uart_sam0_dev_data *const dev_data = DEV_DATA(dev);
uart_sam0.c:498:35: note: previous definition of 'dev_data' was here
498 | struct uart_sam0_dev_data *const dev_data = DEV_DATA(dev);
Fix this be removnig the duplicate at line 558.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The UART driver for samd0 was is missing the .configure and
.config_get functionality expected from api for serial driver.
This commit fixes this by providing basic configuration
Signed-off-by: Kuba Sanak <contact@kuba.fyi>
Convert older DT_INST_ macro use in atmel sam0 drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit fixes the multiple SERCOM interrupt handling for the SAM
D5x and E5x devices by replacing the obsolete device tree symbol with
the new `DT_INST` symbol.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The SAME5x/SAMD5x MCUs share their SERCOM peripherals with the
samd2x and saml1x MCUs with only few registers changed.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
move misc/__assert.h to sys/__assert.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move uart.h to drivers/uart.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move dma.h to drivers/dma.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The defines should have had a _0 on them, now that we generate the
proper defines, fixup the cases that used that old scheme.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This adds support for the async API for SAM0 SERCOM USARTs using
DMA to drive the device.
Tested on SAMD21 with a few trivial programs and with
tests/drivers/uart/uart_async_api.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
Move SERCOM peripherals to use the raw defines generated from DTS
parsing. This adds aliases to the DTS so that the SERCOM number
can still be used for clocking and pinmux.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
The driver was defining a macro with a CONFIG_ prefix but this wasn't
coming from Kconfig. Change the macro name not to conflict with the
Kconfig CONFIG_ namespace.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
poll_out function was returning the character that was sent. It
happens that it is always constant and the return of this functions is
never tested. Changing it to be a void function.
MISRA-C rule 17.7
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
