This change moves .rodata for panic handler and fatal.c into DRAM
Moves panic handler and its dependent functions into IRAM
Signed-off-by: Shubham Kulkarni <shubham.kulkarni@espressif.com>
Disable RTC WDT enabled (by default) by 2nd stage bootloader in ESP-IDF.
This WDT timer ensures correct hand-over and startup sequence from
bootloader to application.
Enabling bootloader caused system clock initialization to fail
when clock rate is greater then 80MHz. This also fixes
esp32 clock source code.
Signed-off-by: Mahavir Jain <mahavir@espressif.com>
When converting ELF to a flashable image, the esptool can only
process up to 16 ELF sections. Zephyr has been happily grouping
similar objects into linker sections which can easily go over
esptool's limit. This patch consolidates the kernel, net, log,
and shell objects into their own sections.
Also remove the app_noinit section as no one is emitting
anything into that section, and it's not being used by other
arch/SoC/boards in Zephyr.
Fixes#20980
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
- Support PLL for Higher Frequencies 80,160,240 MHz
- Support XTAL Frequencies 26MHz, 40MHz
- Clock Driver can't be disabled, because all of the other drivers
will depend on it to get their operating Frequency based on chosen
clock source (XTAL/PLL).
- Add needed references to BBPLL i2c bus ROM functions.
- Add `rtc` node to Device Tree.
- Since All Peripherals Frequency is depending on CPU_CLK Source,
`clock-source` property added to CPU node
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
generated_dts_board.h is pretty redundant and confusing as a name. Call
it devicetree.h instead.
dts.h would be another option, but DTS stands for "devicetree source"
and is the source code format, so it's a bit confusing too.
The replacement was done by grepping for 'generated_dts_board' and
'GENERATED_DTS_BOARD'.
Two build diagram and input-output SVG files were updated as well, along
with misc. documentation.
hal_ti, mcuboot, and ci-tools updates are included too, in the west.yml
update.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Move _LINKER and _ASMLANGUAGE to target.cmake because of how we pick the
linker script that might be used. This way regardless of how or where a
linker.ld gets included we will always set _LINKER & _ASMLANGUAGE (so
any header that needs check based on those defines they can,
specifically generated_dts_board.h)
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Make sure that all sub-sections of .gcc_except_table are mapped in
rodata else C++ builds with exceptions enabled will generate warnings
due to orphan sections.
Signed-off-by: Jan Van Winkel <jan.van_winkel@dxplore.eu>
We now place the linker directives for the SW ISR table
in the common linker scripts, instead of repeating it
everywhere.
The table will be placed in RAM if dynamic interrupts are
enabled.
A dedicated section is used, as this data must not move
in between build phases.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
(Previous patch set was reverted due to issue with priv_stack.
Resubmitting after fixing the faults caused by priv_stack.noinit
not at the end of RAM.)
This adds a linker flag and necessary changes to linker scripts
so that linker will warn about orphan sections.
Relates to #5534.
Fixes#10473, #10474, #10515.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds a linker flag and necessary changes to linker scripts
so that linker will warn about orphan sections.
Relates to #5534.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Move the SoC outside of the architecture tree and put them at the same
level as boards and architectures allowing both SoCs and boards to be
maintained outside the tree.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
2018-09-13 00:56:48 -04:00
Renamed from arch/xtensa/soc/esp32/linker.ld (Browse further)
