This commit adds Device-Tree instances of the Flash controller
to the SAM3X, SAM4E and SAM4S series. The Flash-Controller
is used to get the unique device identifier.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
Replace CONFIG_WDT_0_NAME with DT_ALIAS_WATCHDOG_0_LABEL in samples and
test code. Now that all drivers are DT aware we don't ever set the
Kconfig option.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that everything is DT based for I2C drivers we can rename the
CONFIG_I2C_[0..5]_NAME define to DT_I2C_[0..5]_NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The majority of cases of CONFIG_I2C_x_IRQ_PRI should be
DT_I2C_x_IRQ_PRI. So go ahead and fix them up. Only the i2c_nios
driver still uses Kconfig for getting priority.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The majority of bits where already in place, but some minor support
get the driver name from DTS was needed. Now we select HAS_DTS_WDT
for the driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
All labels containing "_<8-hex-digits>_" or "16550_<3or6-hex-digits>_"
in their names, assumed to be generated by the extracting script,
are updated with the DT_ prefix, to reflect the recent changes made
to the script.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Adding watchdog driver for sam SoC. The current implemntation just
diables the watchdog on device boot.
This PR adds the following support for SAM3X, SAM4S and SAME70
1. Activate processor reset
2. Activate all reset
3. Generate interrupt on watchdog timer expiration.
Signed-off-by: Subramanian Meenakshi Sundaram <subbu147@gmail.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The Zephyr configuration system uses many different files in many
different formats. It makes it a lot easier for users to understand
what these files do if when we use the correct file extensions.
To this end we rename the dts.fixup files to the correct file
extension '.h'.
This is a breaking change for out-of-tree fixup files. Such files will
be detected and given an appropriate error message.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
2018-10-08 11:38:56 -04:00
Renamed from soc/arm/atmel_sam/sam4s/dts.fixup (Browse further)
