Replace the post decrement in loop's conditional into
explicit decrement inside the loop so as to avoid
decrementing the maximum count without enqueueing free rx
buffers into the free rx buffer MFIFO.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add new custom transport type.
This allows user defined transport for MQTT communication.
The user must implement the transport procedure.
Fixes **#27015**
Signed-off-by: Vlad Tuhut <vlad.tuhut@raptor-technologies.ro>
This commit fixes the issue with a compilation of the sample that
uses printk function from cpp code when LOG2 is used and printk
is handled by logging subsystem.
Signed-off-by: Radoslaw Koppel <radoslaw.koppel@nordicsemi.no>
Standard Arduino CLK signal is on D13,
nucleo_l476rg board has been modified accordingly.
Need an overlay to use default x_nucleo_idb05a1 spin D3 (PB3)
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
Move uart/usart pinctrl to common file.
Set status in dedicated m7 or m4 file.
But only one core can control a peripheral instance.
Arbitrary default choice:
usart1 --> m7
uart8 --> m4
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
RXTO event is generated always after ENDRX and driver relies
on assumption that ENDRX event is handled before RXTO. However,
when interrupt is preempted after ENDRX check returned false
and RXTO event is already set handling order would be swapped.
Added addtional check to handle RXTO event only if ENDRX is not
set. If ENDRX is set, it means that it is not yet handled. RXTO
event is not cleared and interrupt will be triggered again and
ENDRX event will be handled first.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
The lis2dw12 sensor can generate the TAP interrupt only on INT1,
while DRDY can be generated on both. The int-pin DT property
specifiy on which pin the DRDY (and not the TAP) can be generated.
This commit fix the way the trigger is set: first the driver checks
the trigger type (DRDY or TAP), then it uses the int-pin information
only in DRDY case but allows setting TAP regardless of int-pin (it
always routes it on INT1).
The previous code was first checking int-pin: if it was INT2 then
the driver refused setting TAP triggers.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This commit aligns lis2dw12 sensor driver to latest multi
instance sensor driver model.
In particular it makes use of the stmemsc common routines
and move ctx handler inside struct config, so that the
bus_init routines can be totally avoided.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Remove all odr values from Kconfig and always init it
at 12.5Hz. It is responsibility of application to set
the rate to a different value using SENSOR_ATTR_SAMPLING_FREQUENCY.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Move lis2dw12 trigger pulse configurations from Kconfigs to Device Tree.
Moreover the dts properties have been renamed as 'tap', which sounds a
better name to immediately catch the feature behind it. Since tap
threshold cannot be zero, this value (which is the default in dts
binding) is used to enable/disable the device feature per each axis.
The event can be generated on INT1 only.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use gpio_dt_spec structure (and related APIs) in config for configuring
the gpio used for drdy and pulse interrupts.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
