Instead of selecting appropriate HAS_HW_NRF_* options for particular
nRF SoCs (and simulated nRF52 target), set their values basing on
information from devicetree.
Correct also semantics of those options so that they are set only when
a corresponding DT node is enabled. This allows using them directly in
Kconfig dependencies of Zephyr drivers for nRF peripherals. Update
appropriately these dependencies.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This update Atmel sam afec driver to use pinctrl driver and API. It
updates all boards with new pinctrl groups format. In addition, it
add overlay files to allow run samples/drivers/adc example.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
In npcx adc driver, we select 'Scan' (Multiple Channels Operation Mode)
mode by default. It means that selected channels in ADCCS will be
converted automatically. Then, read the measured data from CHNDAT
registers if EOCCEV (Event is set after all selected channels are
converted.) flag in ADCSTS is set.
But we enable the wrong interrupt type, INTECEN, during adc
initialization. Ec will send the interrupt after each channel in ADCCS
is converted. It has no harm to the current driver since the driver
reads all selected channels and turns off ADC converter only after
EOCCEV is set in ISR. But it does generate spurious interrupts.
This CL enables the correct interrupt type, INTECCEN, during adc
initialization. Ec only sends the interrupt after all of channels in
ADCCS are converted.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
G4 series have specific LL ADC API that discriminate ADC1 and ADC5
channels. Take this into account in adc_stm32_setup_channels().
Additionally, fix this function to use LL defines as argument of macro
__LL_ADC_CHANNEL_TO_DECIMAL_NB, as good practice.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
After the ADC interrupt is enabled, the interrupt will be triggered
and the ADC channel valid data will be read, so there is no time
limit here.
Refer to the timeout is also set to K_FOREVER in the function of
adc_context_wait_for_completion().
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Re-running the script that checks for the const qualifier missing on
struct device ISR's parameter.
The script also changes the parameter 'arg' to 'dev' when relevant.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Use the devicetree properties to determine if the dedicated temperature or
voltage reference channels should be configured for the ADC.
Fixes#43750.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
This change includes special handling of the internal voltage
reference and internal die temperature channels for all currently
defined STM32 models
The code now looks for specific ADC + channel ID pairs instead
of just a channel ID to determine if the caller is trying to
configure an internal channel.
Signed-off-by: Pete Dietl <petedietl@gmail.com>
According to Kconfig guidelines, boolean prompts must not start with
"Enable...". The following command has been used to automate the changes
in this patch:
sed -i "s/bool \"[Ee]nables\? \(\w\)/bool \"\U\1/g" **/Kconfig*
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The ADC driver of IT81302 chip can support channels 0-7 & 13-16.
This PR adds to implement ADC channels 13-16.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
This adds support for the ads101x (ads1013, ads1014, ads1015) and
ads111x (ads1113, ads1114, ads1115) family of i2c adc devices.
Signed-off-by: Ryan McClelland <ryanmcclelland@fb.com>
Do not used generated macro from devicetree subsys directly
in driver.
Remove definition of it's own "FOREACH_STATUS_OKAY".
Redefine "DT_DRV_COMPAT" for each supported compatible string.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
The ADC sampling of it8xxx2 needs to read each channel in sequence,
so it needs to wait for an interrupt to read data in the loop
through k_sem_take().
In test_adc.c, k_timer_start() is used in the interval test, so we
need to use polling wait instead of k_sem_take() to wait, otherwise
it will cause kernel panic.
k_is_in_isr() can determine whether to use polling or k_sem_take()
at present.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
The ADC driver now supports three different implementations. To maintain
readability, this patch implements an adc_fixup.h that permits more
generic access to relevant registers.
This patch also introduces support for a new third shape ADC - as found
in the SAML21 for example.
Signed-off-by: Attie Grande <attie.grande@argentum-systems.co.uk>
Previously this was expected to be equal to 1 at all times. This doesn't
play well with the sample or other users (e.g: adc_shell). Instead, we
should count the number of active channels in the bitfield, and ensure
that only one is identified.
Signed-off-by: Attie Grande <attie.grande@argentum-systems.co.uk>
This corrects the following:
1. The priority of type cast is lower than member access. So don't need
the redundant parentheses.
2. The macro should be added to the parentheses.
Signed-off-by: Wealian Liao <WHLIAO@nuvoton.com>
Some drivers explicitely casted data/config from void * to the
corresponding type. However, this is unnecessary and, in many drivers it
has been misused to drop const qualifier (refer to previous commits).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Stop using redundant DEV_DATA/DEV_CFG macros and use dev->data
and dev->config instead.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Clear ADRDY before enabling ADC to ensure the subsequent
wait for ADRDY does not stop prematurely in case ADRDY
was already set.
The "ADC on-off control" sections of the following reference manuals
were consulted. That gives at least one instance per series affected
by this change, even if not every affected MCU is covered.
- RM0438 (STM32L552xx and STM32L562xx)
- RM0351 (STM32L47xxx, STM32L48xxx, STM32L49xxx and STM32L4Axxx)
- RM0434 (STM32WB55xx and STM32WB35xx)
- RM0454 (STM32G0x0)
- RM0440 (STM32G4 Series)
- RM0399 (STM32H745/755 and STM32H747/757)
- RM0433 (STM32H742, STM32H743/753 and STM32H750)
- RM0453 (STM32WL5x)
Signed-off-by: Alexander Mihajlovic <a@abxy.se>
Use a wrapper for LL_ADC_Enable that also waits for ADRDY if required
by the SoC to make sure it's properly enabled everywhere this is done.
Signed-off-by: Alexander Mihajlovic <a@abxy.se>
Add a dummy driver for the `vnd,adc` compatible to allow compilation of
drivers utilising an ADC when running "build_all" tests.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Certain stm32 soc's have a single shared irq for all adc channels
on those soc's only a single channel is supported.
Added a Kconfig that enables a shared irq for stm32f2x, stm32f4x,
stm32f7x soc's. The shared IRQ uses a flag to limit the number of
interrupts defined to only 1. A shared irq handler is added which
determines which ADC instance the interrupt is for, it then calls
into the existing interrupt.
Signed-off-by: Marius Scholtz <mariuss@ricelectronics.com>
NPCX7/9 has a different ADC register structure. NPCX7 has 3 threshold
detectors from offset 0x14 & has 10 input channels. NPCX9 has 6
threshold detectors from offset 0x60 & has 12 input channels.
This commit fixes the NPCX ADC register structure.
Signed-off-by: Wealian Liao <WHLIAO@nuvoton.com>
RM 0453: the sw is allowed to write the Oversampling
ratio or shift of the ADC Config.Reg.2 only when ADSTART = 0
(no conversion is on-going). So disabling it will be stopped.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
RM 0453: the sw is allowed to write the Data Resolution bits
of the ADC Config.Reg.1 only when ADEN = 0 (ADC disable).
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The PINCTRL_DT_(INST_)DEFINE macros already defined the trailing ;,
making its usage inconsistent with other macros such as
DEVICE_DT_DEFINE.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
MCHP ADC configuration register need to be updated with appropriate
clock time values for high & low time clock.
Signed-off-by: Aditya Bhutada <aditya.bhutada@intel.com>
The STM32 docs state that the ADC may not be calibrated unless
the ADC is disabled (ADEN=0). This commit implements this constraint
Fixes#40936
Signed-off-by: Pete Dietl <petedietl@gmail.com>
The STM32U5x device has ADC instance of different versions
similar to the stm32H7 about the oversampling.
ADC1 of 14bit resolution has a ratio from 1..1024 on OSR[9:0]
ADC4 of 12bit resolution has a ratio on OVSR[2:0]
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This commit extends the configuration of the oversampling
ratio and shift for the stm32U5xx soc, depending on the
ADC instance: ratio is a value from 1..1024 or a LL_ADC_OVS_RATIO_x
to be used with the stm32Cube LL function.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
On the stm32H7 family, there are ADC which have Oversampling ratio
of 10 bits OSVR[9:0] in the CFGR2 register. It means that oversampling
512x or 1024x are possible.
Other values are not allowed as the oversampling field of the struct
adc_sequence (adc.h) is 2^oversampling.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The adc_stm32_oversampling function is used to configure
the ratio and shift for each sequence->oversampling
depending on the soc serie and ADC instance in the serie
In the stm32H7 serie, only ADC3 of ADC_VER_V5_V90 version
have a LL_ADC_OVS_RATIO_x contant (other a 9bit value).
Signed-off-by: Francois Ramu <francois.ramu@st.com>
