This is always defined since:
755d09e149 include/drivers/clock_control: stm32: Update for STM32F1
support
So the condition has currently no effect and causes the prescaler to
always be set to /2.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
This commit implements the OpenThread APIs to pass MAC keys and
frame counter to the radio layer in order to process the
transmission security. This is needed for the correct functioning
of a CSL transmitter.
Signed-off-by: Eduardo Montoya <eduardo.montoya@nordicsemi.no>
This commit aligns iis2dlpc sensor driver to latest multi
instance sensor driver model.
In particular:
1. make use of some few DT helpers:
- get bus devices with DEVICE_DT_GET
- get SPI information with SPI_CONFIG_DT_INST
- get drdy gpios with GPIO_DT_SPEC_GET
2. make use of the stmemsc common routines and move ctx
handler inside struct config, so that the bus_init
routines can be totally avoided.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The STM32H7x flash has an integrated ECC that can correct single
errors and detect double errors. When a double ECC error is detected,
the DBECCERR1/2 flag is raised and there is a bus fault.
We now mask this bus fault and check the error flags. ECC errors are
logged with the offset of the data. Single ECC errors cause a warning
to be logged and double ECC errors return -EIO.
Fixes#33140.
Signed-off-by: Göran Weinholt <goran.weinholt@endian.se>
Now that we have specific bindings for STM32F100 devices,
we need dedicated treatment for PLL source HSI case.
Otherwise, we end up using undefined symbol STM32_PLL_PREDIV1.
Please note that previous code compiled, it was assigning
a wrong value to prediv. This had no consequence because
prediv value is forced in Cube LL functions.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
According to RM0041.pdf clock tree for stm32f100xx devices is
different from both STM32F10X density and connectivity lines devices,
but is a combination of both.
Rework symbols definitions so that STM32F100xx is neither of those
and uses:
- CLOCK_STM32_PLL_MULTIPLIER as on SOC_STM32F10X_DENSITY_DEVICE
- CLOCK_STM32_PLL_PREDIV1 as on SOC_STM32F10X_CONNECTIVITY_LINE_...
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Two minor tweaks and a semantics change:
- fix a whitespace nit
- use gpio_pin_configure_dt()
- turn the LED on in case the percentage is nonzero
The last change patterns this driver after behavior in the Android
lights HAL, which recommends analogous behavior when the user requests
a color change in a non-RGB LED:
Do your best here. [...] If you can only do on or off, 0 is off,
anything else is on.
https://source.android.com/reference/hal/structlight__state__t
I think this behavior makes more sense.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Use the CODE_DATA_RELOCATION_SRAM config to indentify code relocated
to SRAM so we can setup the MPU for the SRAM region used for code
relocation.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
The AUDIO_DMIC INIT_PRIORITY definition is set to 60 by default,
but this value is causing dmic drivers to be initialized prior to
i2s, to which they are dependent from.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
We need to clear interrupt status, before we enable the interrupt.
So I let ite_intc_isr_clear() to be global function.
Signed-off-by: Ruibin Chang <ruibin.chang@ite.com.tw>
The i2s_config structure passed to the i2s_configure() function is
not supposed to be modified by the driver. Similarly, the structure
returned by the i2s_config_get() function is not supposed to be
modified outside the driver.
Decorate the pointers to those structures with the const qualifier
and correct one driver that actually modified the structure passed
to i2s_configure().
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Introduce a new enumeration value that allows setting configuration
and triggering commands for both I2S streams simultaneously.
Such possibility is especially important on hardware where the streams
can be only enabled/disabled (but not started/stopped) independently,
like it is in nRF SoCs.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Automatic collision detection for half-duplex mode can be enabled
by setting `collision-detection` proprety for uart hardware
in the dts file. If the transmitted bit does not match the received
bit an error is raised. This is useful in RS-485 half-duplex mode.
Signed-off-by: Arvin Farahmand <arvinf@ip-logix.com>
Currently cavs_idc_smp_init() is called from a system
initialisation sequence, which only runs on the main CPU.
However, it must also run on secondary CPUs if those are
powered on later instead of simultaneously with the main
CPU.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
irq_enable() should be called with the composite IRQ code as its
argument, not just the Xtensa proper part of it.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Update stm32h7 clock_control driver to make use of macros allowing
dts based configuration in coexistance with existing Kconfig method.
Note: Use of IS_ENABLED is removed as it generates warnings in
checkpatch. This checkpatch behavior needs to be reviewed but may
first require a little clean up of IS_ENABLED macro.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Information about which block protect bits are set on power-up is not
inferable from SFDP content, so we need the devicetree config pointer
to get the has-lock property value even when SFDP data is read at
runtime.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
During configuring the low-voltage power supply of IO pads, the npcx
GPIO driver needs to set the related PORTx_OUT_TYPE bit to 1, i.e.
select to 'Open Drain IO type', also. This CL provides a mechanism that
configuring these bits via 'def-lvol-io-list' node automatically in case
the flag of gpios that have been configured to low-voltage power supply
doesn't contain GPIO_OPEN_DRAIN.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
The memory block passed by the user to the i2s_write function is
tightly packed next to each other.
However for 8-bit word_size the I2S hardware expects the data
to be in 2bytes which does not match what is passed by the user.
This will be addressed in a separate PR once the zephyr API committee
finalizes on an I2S API for the user to probe hardware variations.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
1. Update the SDK API's called in the configure implementation.
The DMA_PrepareTransfer and DMA_SubmitTransfer SDK functions
are not recommneded for use. Replaced the call to these SDK
functions with other SDK API's.
2. Fix the implementation the configure function when multiple
blocks are used.
3. Update the dma_reload implementation. The old reload function
would simply abort the transfer. The new implementation reloads
the DMA buffers for transfer.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
To allow transition to device tree based clock configuration on
stm32 targets, rework clock_control driver to use intermediate
STM32_ macros initially defined as the equivalent Kconfig macros
for now.
Propagate the change in all code using these macros.
The reason to introduce these new macros instead of configuring
Kconfig flags using dt kconfigfunctions is that we'll need
to be able to inform users that Kconfig flags are deprecated
once the whole family conversion is done, to encourage
out of tree users to adopt this new configuration scheme.
Note: For now STM32H7 series and code is excluded.
This is the same for some series specific code such as
PLL mul/div for L0/L1 and XTRE prescaler on F1 series.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add configurable attached event delay. Delay can be used to give
USB Charging Controller time for initialization.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
LL_RCC_HSE_EnableBypass() doesn't exist on stm32wl,
but can be replaced by LL_RCC_HSE_EnableTcxo()
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
Use recently introduced API, which takes care of gracefully closing any
pending DNS requests and replacing existing DNS server list with new
one.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Use recently introduced API, which takes care of gracefully closing any
pending DNS requests and replacing existing DNS server list with new
one.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reboot functionality has nothing to do with PM, so move it out to the
subsys/os folder.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
