Remove leading/trailing blank lines in .c, .h, .py, .rst, .yml, and
.yaml files.
Will avoid failures with the new CI test in
https://github.com/zephyrproject-rtos/ci-tools/pull/112, though it only
checks changed files.
Move the 'target-notes' target in boards/xtensa/odroid_go/doc/index.rst
to get rid of the trailing blank line there. It was probably misplaced.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Fetch HW models from a new west module.
And, remove all pre-west glue which was used to:
* Fetch them in CI
* Validate their vesion
* Modify the include path and link to them
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Adds a device tree nexus node to define which gpio pins are mapped from
the soc to the arduino header.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a device tree nexus node to define which gpio pins are mapped from
the soc to the arduino header.
The frdm_kw41z board excludes the arduino A0 pin because it cannot be
muxed as a gpio on the soc.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables the high-speed spi instance 8 on the lpcxpresso55s69 board.
Configures pinmuxes and clocks, and updates board documentation
accordingly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
64BIT has no prompt. Assignments in configuration files have no effect
on symbols without prompts. A prompt means the symbol is
user-configurable.
64BIT is instead enabled indirectly through being selected by
BOARD_QEMU_RISCV64, which is enabled in the same configuration file.
Detected through some work-in-progress improved error checking.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
CPU_MINUTEIA has no prompt. Assignments in configuration files have no
effect on symbols without prompts. A prompt means the symbol is
user-configurable.
CPU_MINUTEIA is instead enabled indirectly through being selected by
other symbols.
Detected through some work-in-progress improved error checking.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
USE_CODE_PARTITION is a bit vague as a symbol name ("use code partition
how?"). Rename it to USE_DT_CODE_PARTITION to make it clearer that it's
about devicetree.
This would break any third-party configuration files that set it, but
it'll generate an error since kconfig.py promotes warnings to errors, so
it's probably not a big deal.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
In board pinmux.c ifdef of the form DT_GPIO_KEYS_SWx_GPIO_CONTROLLER
should be DT_GPIO_KEYS_SWx_GPIOS_CONTROLLER.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The original v1.3 had MMA8653+MAG3110, but v1.5 has verified LSM303AGR
and theoretical FXOS8700. Add the v1.5 variant 1 nodes in disabled
form; they can be enabled through overlays.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Created MEC1501 deep and light sleep example for MCHP MEC1501.
Modifications were made to SoC, board, timer, and hello world
sample program. Power management split into SoC power
implementing the interface and device power for device specific
logic.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Extended flash simulator for posix architecture to read/write data
from a binary file on the host file system.
Further enable the flash simulator by default on native_posix(_64)
boards and updated the documentation accordingly.
Signed-off-by: Jan Van Winkel <jan.van_winkel@dxplore.eu>
olimexino_stm32 board doesn't have a
debugger. Now that stm32flash
runner is available, let's use it.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
SOC_FAMILY_ARM has no prompt. Assignments in configuration files have no
effect on symbols without prompts. A prompt means the symbol is
user-configurable.
SOC_FAMILY_ARM is instead enabled indirectly through being selected by
other symbols.
Detected through some work-in-progress improved error checking.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Commit ceffca2c42 added DTS support for board LEDs and buttons. Remove
redundant LED0_GPIO_PORT, SW0_GPIO_NAME, etc. defines.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Add dts configs for bt-c2h-uart and bt-mon-uart. These are used by
the hci_uart sample and BT_DEBUG_MONITOR.
Signed-off-by: Rubin Gerritsen <Rubin.Gerritsen@nordicsemi.no>
In order to avoid a warning from Sphinx complaining that the
supported_features.rst file is not included in any ToC, rename it to
.txt so that Sphinx understands that this is only a snippet to be
included in other files.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The HiFive1 boards power up using a 32 KiHz low frequency kernel, so
have a cycle rate of 32768 Hz. The board definitions have not been
revisited since the Zephyr default for ticks-per-second increased from
100 to 10000. The timer system on the board does not operate
correctly at 4 cycles per tick, but does at 328 cycles per tick.
To support functional timers while keeping system milliseconds in sync
with clock time set ticks-per-second to 128.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
For consistency with all other boards, make the `buttons` node a child
of the root node, not the `leds` one.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
On LSM6DSO sensor the INT1 pin is used for both generating the drdy
interrupt and for switching to I3C hotjoin mode just after reset if
it is at logical '1' level. If you reset the x_nucleo_shield3 board
the LSM6DSO enter in hot join, as INT1 '1' level is preserved by
the level shifter.
This commit switch to INT2 to generate DRDY interrupt, so that INT1
always remain to logical '0' level.
Fixes: #20933
Signed-off-by: Armando Visconti <armando.visconti@st.com>
mps2_an521 is the default board for ARMv8-M architecture with
support for Security Extension, and CI should test building and
running samples and tests on this board by default. As the focus
is on kernel, userspace, and arm test suites, certain tags are
set to be ignored when testing on this platform.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
In Zephyr we have the rule of "do not use stdint defined types",
but unfortunately that leaves us with no properly defined
format specifiers for printing values out.
So cast to stdint types in this expression to actually be able to
do so.
Fixes Coverity CID: 205798
Fixes Coverity CID: 205825
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
When building with support for BLE stack on the nRF5340 APP CPU
(Application MCU), use RPMsg HCI driver by default.
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
When building with support for BLE stack, enable the BT_ECC
for the nRF5340 NET CPU (Network MCU).
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
When building with support for BLE stack, enable the Vendor Specific
commands for the nRF5340 APP CPU (Application MCU).
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
Provide the mapping from FE310-G002 GPIO pins to the Arduino Uno
headers. Note where pins have pre-assigned functions that may
interfere with use as GPIOs with the default pinmux assignments.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Adds missing items to the list of supported features for all nxp imx rt
boards. These features were already supported, just missing from the
list.
This change increases the number of samples and tests that sanitycheck
selects for these boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Sorts the list of supported features in alphabetical order for all nxp
boards. No features are added or removed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Link to Nordic Semiconductor Infocenter, instead of DocLib
in the documentation for nRF-based Development Kits.
Change Nordic Semi to Nordic Semiconductor in the
DK figure captions.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Some people are behind firewalls that prevent them
from doing ssh connections.
Change the default BabbleSim fetching instructions to
be over https which should work for everybody.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
A partition start offsets should be expressed relative to the flash
device base address. For cpunet flash partitions start offsets
were improperly expressed as absolute flash address.
This patch fixes partitions start addresses for nRF5340 cpunet.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Since the nRF5340 DK contains the required DC/DC circuitry,
enable it by default while keeping it configurable. This
reduces power consumption in application core , network
core and high voltage use.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Explicitly configures the rgb led pinmuxes as gpios. Currently the gpio
driver quietly changes the pinmux to gpio mode when configuring a gpio
pin, but this behavior is about to change.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Some board description files failed to note where gpio was supported,
causing tests to be inappropriately filtered. Add the feature where
the gpio_basic_api test would use it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Name convention for nordic USB driver changed
Kconfig files for custom boards have to be udapted accordingly.
Changes affect only name convention change.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
