Add a new Kconfig symbol that explicitly controls whether the vector
table should be placed in RAM. This eliminates the side effect of
`IS_BOOTLOADER` controlling vector table location. Making the condition
a positive assertion also allows the config to be used in CMakeLists
conditions (`zephyr_linker_sources_ifdef()`, etc).
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Remove the `IS_BOOTLOADER` and `BOOTLOADER_SRAM_SIZE` symbols from the
`nucleo_l053r8` and `nucleo_l031k6` boards. The stated reason for
inclusion is to disable the RAM vector table, however this doesn't apply
to the STM32L0 series, only STM32F0.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
This commit enables flash support for stm32h747i_disco_m7
in device tree. This has been tested with flash sample
application on stm32h747i_disco platform with m7 core.
Flash is shared between two cores (M4 & M7) so the last 1M is
assigned to M4 core. Hence allocating 1M of storage at the
end of first 1M.
Signed-off-by: Krishna Mohan Dani <krishnamohan.d@hcl.com>
Add support for u-blox EVK-NINA-B4, which uses the nRF52833
This board is similar to the nrf52833dk_nrf52833, though it
uses a u-blox NINA-B40x openCPU module with DC-DC support
included.
Simplified pwm LED aliases
Corrected LED assignments for red, green, and blue
Addressed review comments (spi & gpio 0 0)
Tested with blinky, button, and Bluetooth peripheral_hr
Signed-off-by: Bob Recny <bob.recny@u-blox.com>
When I added this board recently I mistakenly placed
the Arduino SCL pin (Default Zephyr pin) as PB6
when it should be PB8.
The SPI node is now properly set to SPI2 peripheral
instead of SPI1. SPI2 is the most suitable to follow
the silkscreen on the printed circuit board.
Added arduino_gpio to yaml.
Signed-off-by: Guðni Már Gilbert <gudni.m.g@gmail.com>
Update configuration of qemu_cortex_m0 to use LF XTAL as low
frequency clock source. Previously used RC requires more
modules to be fetched into the build, including TEMP sensor
used for clock calibration.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Support the ST STM32G071B Discovery board with STM32G071RBTX SoC
Tested with:
- `samples/basic/blinky`
- `samples/basic/button`
Flashed samples via On-Board ST-LINK with:
- west flash
Signed-off-by: Sam Hurst <sbh1187@gmail.com>
hsdk has an on board cy8c95xx I/O expander, and 4 on
board LEDs use the expander GPIO. Add the I/O expander
and LEDs in hsdk dts, then add documents for them.
Signed-off-by: Watson Zeng <zhiwei@synopsys.com>
Add support for u-blox EVK-NINA-B1 which uses the nRF52832.
This board is similar to the nRF52dk_nrf52832 with
different pin assignments on the header pins and not having
the debug-in and shield SWD headers.
Tested with blinky, button, and Bluetooth peripheral_hr
Corrected duplicate pin assignment for i2c1 in dts file
Corrected copyright date in Kconfig.defconfig
Rebase to update test_adc.c
Corrected sda-pin, scl-pin assignments and LED aliases
Signed-off-by: Bob Recny <bob.recny@u-blox.com>
Add support for the FVP Base RevC 2xAEMv8A board to be emulated using
the same FVP. For now the virtual platform is only exposing one core and
the basic set of peripherals (GICv3, ARM arch timer, PL011, etc...).
INFO - Total complete: 256/ 256 100% skipped: 933, failed: 0
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Introduce revision for cy8ckit_062_ble board. Revision 0.0.0 represent
the original board schematic which connects Arduino header signals to
PSoC-6 KitProg. The revision 1.0.0 should be used after board rework
to access other serial ports and full Arduino headers.
Signed-off-by: Gerson Fernando Budke <gerson.budke@atl-electronics.com>
Add pinctrl and interrupt information for both cores. The uart-6 is
the default serial communication on the kit connected to m0 core. It
uses SCB[6] and the NVIC line 21 as interrupt source on Cortex-M0+ cpu.
The line 21 is an arbitrary value and users can select any value. The
SCB[6] shares pins with Arduino headers D8/D9. It may be necessary an
USB serial converter to sample signals and enable Zephyr console on PC.
The uart-5 is the default serial communication port for m4. It is
connected to Arduino serial line. A HW rework may need to allow
Arduino header to be useful.
Signed-off-by: Gerson Fernando Budke <gerson.budke@atl-electronics.com>
Add pinctrl and interrupt information for both m0/4 cores. The uart-5
is the default serial communication on the kit and it is connected to
Cortex-M0+ cpu. It uses SCB[5] and the NVIC line 21 as interrupt
source on Cortex-M0+ cpu. The line 21 is an arbitrary value and users
can select any value. The SCB[5] shares pins with Arduino headers
D0/D1 and it is wired with the on-board USB Serial converter. This
means, if use wants use an external shield it must rework the board.
The uart-6 is the default serial communication for Cortex-M4 cpu, which
uses SCB[6].
Signed-off-by: Gerson Fernando Budke <gerson.budke@atl-electronics.com>
The current serial driver uses hard code configuration. Rework driver
to use pinctrl and enable full configuration from device tree.
Signed-off-by: Gerson Fernando Budke <gerson.budke@atl-electronics.com>
Add pinctrl-0 properties for configuration of UART, I2C, SPI, FTM,
DAC, ADC, ACMP, and PWT peripherals. These settings are based on what
is defined in the board/pinmux.c file.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
We do not need to have dependencies any more on !OPENAMP
for BUILD_WITH_TFM in the mps2 an521 target, because we
now have different targets for the non-secure version of
the board and the remote core.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Add a new target for MPS2 AN521, called mps2_an521_remote.
This target is used in dual image MPS2 AN521 builds, for
the 'remote' target. It is indentical to mps2_an521_nonsecure,
except for the fact that it does not enable TrustZone-M and
it does not set the security domain to Non-Secure.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Add dts nodes for onboard devices that have drivers in zerphyr src
- Add PWM for all leds
- Add LSM303AGR sensor node
- Add LSM303DLHC node for PCB rev B
- Create PCB rev B overlay and make PCB rev D default.
Signed-off-by: Sahaj Sarup <sahaj.sarup@linaro.org>
Adds nucleo_g071rb board to the uart_async_api test.
Therefore additionally add usart1 in board definitions.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Enables dma test cases loop_transfer and chan_blen_transfer
on stm32g03116_disco, nucleo_g071rb and nucleo_g0b1re.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
The configuration is based on
the f303k6 and the ST reference manual.
I had successfully tested the following sample code:
blinky
blink_led (uses TIM2_CH2 on PB3)
hello_world
Signed-off-by: Sebastian Schwabe <sebastian-schwabe@gmx.de>
Add a note in the board documentation regarding the
correct size of the available flash and sram memory.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
In Cortex-M, SVC exceptions are used by the kernel
for system calls, run-time exceptions and IRQ
offloading. Correct the respective information in the
boards documentation.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This change enables A, C, D, E, G, H, I, J, K, and L groups,
and fix gpio interrupt function.
This change also pull (and rename) dt-bindings/irq.h to
dt-bindings/interrupt-controller/ite-intc.h, because it is
chip-specific.
Signed-off-by: Dino Li <Dino.Li@ite.com.tw>
Change-Id: Ifee039981c2cc4cf5980e663702a9921e629fc1e
NPCX PWM supports output buffet select to push-pull or open-drain. Add
output buffer select option 'drive-open-drain' in devicetree for NPCX
PWM. If set, the PWM output will be configured as open-drain. If not
set, defaults to push-pull.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Signed-off-by: Wealian Liao <WHLIAO@nuvoton.com>
1. add a seperate 2 cores SMP board configuration to run in Jailhouse
inmate Cell, root Cell Linux will use Core0 and Core1, Zephyr will
run on Core2 and Core3.
2. Refine the code of dts, move SoC common dts nodes into dtsi fiel in
dts/arm64/nxp/ directory.
3. Add myself to be code owner of directory dts/arm64/nxp/.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Add support for u-blox EVK-ANNA-B1 which uses the nRF52832.
This board is similar to the nRF52dk_nrf52832 with
different pin assignments on the header pins and not having
the debug-in and shield SWD headers.
Tested with blinky, button, and Bluetooth peripheral_hr
Addressed review comments, including SW2
Rebased to pick up new board in test_adc.c - corrected typo
Reverted to sda-pin, scl-pin
Signed-off-by: Bob Recny <bob.recny@u-blox.com>
Enable the user led and user switch that can be found
on h3ulcb, they are both connected to the GPIO 6 bank.
Signed-off-by: Julien Massot <julien.massot@iot.bzh>
Adding ulcb boards documentation based on Renesas official documentation
and following zephyr guideline.
The documentation is describing the board and the current
Zephyr support.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
Add basic configuration for H3ULCB, just enough to see the
Zephyr boot banner on the ram console.
This configuration make use of the Cortex-R7 present on
r8a977951 SoC.
Signed-off-by: Julien Massot <julien.massot@iot.bzh>
