Using IRQ as source for interrupt values can
fail when installing irq_connect_dynamic, as
IRQ can previously be enabled. This updates
the logic to use source map and allows
default irq_enable() and irq_disable() to call
esp32c3 interrupt allocator implementation.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Re-running the script that checks for the const qualifier missing on
struct device ISR's parameter.
The script also changes the parameter 'arg' to 'dev' when relevant.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Refactors interrupt controller drivers to use the shared driver class
initialization priority configuration, CONFIG_INTC_INIT_PRIORITY, to
allow configuring interrupt controller drivers separately from other
devices. This is similar to other driver classes.
The default is set to CONFIG_KERNEL_INIT_PRIORITY_DEFAULT to preserve
the existing default initialization priority for most drivers.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
On 32bit compiler the BIT_MASK(32) generate a warning,
after discussion on #42226 and #42163, advise was to use
BIT64_MASK instead.
Signed-off-by: Julien Massot <julien.massot@iot.bzh>
These definitions are required to be able to use GICv3
interrupts controller on an ARMv8 AArch32 processor.
Signed-off-by: Julien Massot <julien.massot@iot.bzh>
According to Kconfig guidelines, boolean prompts must not start with
"Enable...". The following command has been used to automate the changes
in this patch:
sed -i "s/bool \"[Ee]nables\? \(\w\)/bool \"\U\1/g" **/Kconfig*
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The device instance can be obtained at compile time. Here
DEVICE_DT_GET_OR_NULL is used as the following code seems to accept a
NULL condition, meaning instance is optional.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Some drivers explicitely casted data/config from void * to the
corresponding type. However, this is unnecessary and, in many drivers it
has been misused to drop const qualifier (refer to previous commits).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Stop using redundant DEV_DATA/DEV_CFG macros and use dev->data and
dev->config instead.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
In order to align with macros used to obtain a device reference (e.g.
DEVICE_DT_GET), align the PM macros to use "GET" instead of "REF". This
change should have low impact since no official release has gone out yet
with the "REF" macros.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
For functions returning nothing, there is no need to document
with @return, as Doxgen complains about "documented empty
return type of ...".
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The gd32_exti_isr function may be unused if the GPIO driver is not
enabled but EXTI is (no IRQ will connect to it). This may be improved in
the future by requiring explicit enablement of the exti DT node.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Theoretically, source id check is not mandatory in the context we use
VT-D here (i.e. non VM one, just multi-vector MSI support)
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Not sure this is requered as we do not mangle with domains, but let's
make sure this cache is clear.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
A surprising issue: while sys_set_bit() on VTD_GCMD_REG work on
apollo_lake, it seems to create border effect on elkhart_lake: it may
reset some previous bit to 0.
So switching to full write of the register at once, which works for
both.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
VT-D will only be enabled if MSI multi-vector will also be requested,
on x86_64, for all boards BUT QEMU ones.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
There is no point to enable VT-D if PCIE MSI multi-vector support is not
requested, as VT-D is uniquely being used to remap MSI multi-vector
based interrupts.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Those MMIO registers might be mapped in RAM and thus it's
really important to keep storage space for such mapping.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
QI operation are not supposed to last forever.
It's not an actual timeout based on clock, but a dummy counter instead.
That's because system clock might not have beed initialized yet, since
VT-D's init comes first (and that same init will use QI...)
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Depending on a VT-D capability, it might be necessary to flush objects
from the cache.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Looks like it's mandatory to invalidate the Interrupt Entry Cache in
VT-D and the only way to do so is to enable Queued Interface.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
IR faults are non-recoverable, so it's good to know why. Thus let's
handle the fault event and print the fault.
Other faults are printed as well.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Looks like a source of fault if pieces of IRTE are written instead of
the whole 64 bits block it belongs to.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
If VT-D's interrupt remapping is in place, all IOAPIC RTEs need to get
remapped as well (or then they will be simply blocked).
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Adding a way to pre-install the irg/vector on an irte and a way to get
an irte based on irq/vector.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This will not only be used by MSI remapping but by all relevant
interrupts.
Fix also IRTE settings:
- handle x2apic for destination id
- destination mode is always logical (as for IOAPIC)
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
In XAPIC mode, it's possible to tell VT-D to let interrupt in compatible
format passing through.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
SHV bit depends on the number of vectors allocated.
If it's facing a multi-vector MSI array, it will set the bit.
If not the bit must be 0.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Instead of using maskstatus to see if an interrupt has fired,
use finalstatus instead. It has been observed that some
controllers do not update maskstatus correctly with incoming
interrupts, but finalstatus works fine.
FYI, the DW driver in Linux is also using finalstatus.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add initial support for the GigaDevice External Interrupt Controller.
This driver is required to manage GPIO interrupts. Only EXTI lines 0 to
15 are supported for now (no LVD, RTC, etc.). Driver can be extended in
the future to add support for extra EXTI lines.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
The device PM subsystem _depends_ on device, not vice-versa. Devices
only hold a reference to struct pm_device now, and initialize this
reference with the value provided in Z_DEVICE_DEFINE. This requirement
can be solved with a forward struct declaration, meaning there is no
need to include device PM headers.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Port some drivers to the recently introduced macros to showcase its
usage and be able to do some initial testing (nRF52840).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Define the device using DEVICE_DEFINE macro, so that a single option can
be used regardless of PM being enabled or not.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The PM callback is no longer referenced as "pm_control" but
"pm_action_cb", so reflect this new naming on the callbacks.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
