Remove the flash node defined in the default `v0.9.0` variant before
adding a new node for the `v0.7.0` variant. Fixes two instances of
`jedec,spi-nor` being present in the final dts.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Update i2c_emul.c to support i2c_target_register and i2c_target_unregister
function calls as well as support address forwarding in emulation.
Address forwarding helps us test IPCs in native sim. Instead of having to
emulate 2 separate cores, we can forward read/write requests from one bus
to another bus (effectively creating a loop). This way the same image can
simulate both the controller and the target.
Signed-off-by: Yuval Peress <peress@google.com>
Add MAX32666EVKIT board file and documentation
For more information about this board please check
https://www.analog.com/
Signed-off-by: Sadik Ozer <sadik.ozer@analog.com>
Add MAX32662EVKIT board files
For more information about this board please check
https://www.analog.com/
Co-authored-by: Maureen Helm <maureen.helm@analog.com>
Signed-off-by: Sadik Ozer <sadik.ozer@analog.com>
Enable the rng module for the google_dragonclaw board by default.
The RNG module is always used anyway and it helps with running tests
that needs entropy.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
This update is to support clock API for RA8
Move the clock initialize function into clock driver
Peripheral clock now has 2 more property in clock cell for enable
and disable clock to peripheral module
Signed-off-by: Duy Phuong Hoang. Nguyen <duy.nguyen.xa@renesas.com>
Added MAX32675EVKit board
For more information about this board please check
https://www.analog.com/
Co-authored-by: Maureen Helm <maureen.helm@analog.com>
Signed-off-by: Sadik Ozer <sadik.ozer@analog.com>
Enable DMA peripheral support on MAX32655EVKIT and FHTR boards.
Co-Authored-By: Sadik Ozer <sadik.ozer@analog.com>
Signed-off-by: Jason Murphy <jason.murphy@analog.com>
While executing from MRAM will likely never happen in practice for the
FLPR core, add such variant for testing.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
These shields in the Arduino form factor can be mounted on supported
boards and can provide Wi-Fi6 capability.
Base shield is nRF7002, with variants as nRF7001 (2.4GHz only) and
nRF7000 (dual band scan only).
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Enable commonly-used I2C in ADI MAX32 boards by default to access I2C
functionality without having to create an additional overlay file.
Signed-off-by: Tahsin Mutlugun <Tahsin.Mutlugun@analog.com>
It looks like both cpuapp/cpunet cores share the same definitions for
LEDs, buttons and Arduino connector. This patch puts these repeated
definitions into a single shared file.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
The WeAct STM32F405 Core Board is an extremely low cost and bare-bones
development board featuring the STM32F405RG, 64-pin variant of
the STM32F405x series.
Signed-off-by: Pavlo Yadvychuk <pyadvichuk@gmail.com>
Remove the logic from the board level about overriding the
flash load size and instead just select to use the DT code
partition if app is not expected to be able to occupy the
whole flash space because of the firmware image being
loaded separately.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Clean up before deprecating legacy device support.
The Linux kernel driver for this example has never been upstreamed or
implemented upstream. In general, 15.4 development does not seem to be a
big success, but if it comes up again, the protocol used by the example
will need to be redesigned anyway.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
