Reset rx byte counters when hw timer/counter is disabled.
Fixes issue where disabling and re-enabling async uart rx can produce
"UART_RX_RDY" events with invalid data when power management is used.
Signed-off-by: Audun Korneliussen <audun.korneliussen@nordicsemi.no>
These are all the case that coccinelle cannot find as they are inside
macro declarations.
Fixed via:
git grep -rlz -E "\(struct device \*" |
xargs -0 sed -i 's/(struct device/(const struct device/g'
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
uart_rx_enable might be called after reception is stopped by lack
of buffers with flow control enabled. In that case there is a couple
of bytes kept in the HW FIFO. When HW TIMER is used for byte counting,
it is using RXDRDY event to count bytes. RXDRDY event is generated when
byte is received in RXD. RXD is the head of HW FIFO. When DMA ends and
ENDRX event is generated, transmitter still transmits until RTS line
goes high and transmitter reacts to it and stops transmitting. First
byte received after ENDRX lands in RXD (and generates RXDRDY event),
next by goes to RXD+1 (does not generate RXRDY event).
RXDRDY event after ENDRX is counted by the TIMER. If TIMER is reset
before restarting RX this byte is lost in the calculation. Because of
that byte counters cannot be reset before enabling RX thus move to
initialization. It applies only to HW counting but to keep it consistent
resetting was removed for both modes.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Added detection of uart_rx_buf_rsp call which happend to late when
uart is already disabled.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
When `CONFIG_UART_ASYNC_API` is enabled, cleanup any pending synchronous
receptions at initialization time. Pending receptions are present when
this driver is used with the default mcuboot application.
When `CONFIG_UART_ASYNC_API` is not enabled, RX is always enabled by
this driver. As mcuboot does not use the async API, and does not cleanup
the UART driver before jumping to the next application, that application
boots with RX still enabled. This results in a 500uA increase in current
consumption.
Fixes#26555
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Per the nrf9160 datasheet, UARTE must be disabled prior to configuring
PSEL.TXD, PSEL.RXD, PSEL.CTS, and/or PSEL.RTS. This also ensures that
any prior running code, such as a bootloader, which leaves the UART
enabled will not prevent the Zephyr application from changing the
configuration.
Make a similar change also to the uart_nrf_uart.c driver for the
nRF5 series.
Fixes 27080
Signed-off-by: Pete Skeggs <peter.skeggs@nordicsemi.no>
So far, when rx_disable was called then received data was discarded.
This is currently not according to the API but it is needed if
rx_disabled is called due to out of band information about end of
packet.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Cleaned up flow control configuration. Added support for using only
cts or only rts.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
This is a follow-up to commit cf7dd4981f.
When disabling RX, it is necessary to clear the RXSTARTED event after
the ENDRX_STARTRX shortcut is deactivated, as the event might already
have been generated at this point. If the event is not cleared and
the disabling of RX is done from the user handler called in the context
of the ENDRX interrupt, a spurious UART_RX_BUF_REQUEST event will be
generated (although RX is already disabled) for which a corresponding
call to uart_rx_buf_rsp() would fail, as the second buffer is already
set. Depending on the application implementation, this can result in
other unexpected problems.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
When the loop that tries to obtain the lock in poll_out() finishes
because of hitting the max number of trials (what normally should
never happen), force the lock to be taken instead of just giving up
with sending the data. The latter approach that was in use so far
could not deal with a situation when some thread was aborted while
keeping the lock. Other threads would then have no chance to send
anything with poll_out() until it was called from an ISR.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Although it is not clearly specified in the UART API, this function
is supposed to return 0 when the TX interrupt is disabled, regardless
of whether anything could fit into the TX buffer or not (this can be
concluded from looking at implementations of several samples and tests
present in the tree, also almost all UART drivers are implemented this
way).
The problem in the uart_nrfx_uarte driver case is that the flag that
allows generation of the TX interrupt is not cleared directly in the
uart_irq_tx_disable() function but this clearing is deferred to the
end of the current transmission, in case one is in progress, and hence
it is done in the interrupt handler. Consequently, when the interrupt
handler is not entered between calls to uart_irq_tx_disable() and
uart_irq_tx_ready() (e.g. when both functions are called in a loop
executed in the interrupt context), the latter may return an invalid
value.
Fix this problem by additionally checking if the TX interrupt was
requested to be disabled, not only if it is already disabled in
hardware.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
In some cases (eg at high baud rate, no HW flow control, and when BLE
radio/ints running) data could be lost between when enough characters
have been RX'd to fill the DMA buffer and when the ENDRX event was
fired, where the the STARTRX task is invoked to start filling the next
buffer (which is set up earlier, but I think will not be filled until
STARTRX).
To fix this, the SHORT is enabled between ENDRX and STARTRX whenever the
'next' buffer is available, so that STARTRX is invoked automatically and
subsequent chars go into the next buffer via EasyDMA.
To make this work properly, uarte_nrfx_isr_async() now handles the ENDRX
event _before_ the STARTRX event.
There was also an issue in rx_timeout() where the received character
count (rx_total_byte_count) could be incremented greater than the actual
buffer size. This arises from rx_total_byte_count value coming from the
counting the RXDRDY events (either by PPI/timer counter or counting the
RXDRDY ints themselves) and so if chars are received in the rx_timeout()
(or before ENDRX is handled) the rx_timeout() could increment rx_offset
past the length of the buffer. This could result the remaining 'len'
being calculated incorrectly (an underflow due to unsigned - signed ,
where signed > unsigned).
To fix this, we now store the lengths of the buffers and don't invoke
the UART_RX_RDY callback when the buffers are full; its handled by
ENDRX.
(Also note that the buffer size should be available via the RXD.MAXCNT
register on the nrf, but this register is not exposed through the nrfx
HAL and is also double buffered, so it seemed clearer to just track the
buffer lengths explicitly here in the driver).
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
for fixup
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
Kernel timeouts have always been a 32 bit integer despite the
existence of generation macros, and existing code has been
inconsistent about using them. Upcoming commits are going to make the
timeout arguments opaque, so fix things up to be rigorously correct.
Changes include:
+ Adding a K_TIMEOUT_EQ() macro for code that needs to compare timeout
values for equality (e.g. with K_FOREVER or K_NO_WAIT).
+ Adding a k_msleep() synonym for k_sleep() which can continue to take
integral arguments as k_sleep() moves away to timeout arguments.
+ Pervasively using the K_MSEC(), K_SECONDS(), et. al. macros to
generate timeout arguments.
+ Removing the usage of K_NO_WAIT as the final argument to
K_THREAD_DEFINE(). This is just a count of milliseconds and we need
to use a zero.
This patch include no logic changes and should not affect generated
code at all.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Added return -ENOTSUP in uart_rx_enable() if RX pin is disabled.
Fixed power management call where TASKRX was started even though
RX pin was disabled.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
After RX is disabled during receiving, some bytes are received to
internal fifo. To not interfere with further transactions fifo has to be
flushed.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Added locking for TX transfers between async and polling API.
Added safety counters for checking if transmission finished.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Update hal_nordic's revision, so that NRFX_ASSERT uses __ASSERT_NO_MSG
directly, not through the assert macro that comes from from libc,
as the definition of the latter might be different when some specific
libc version is used, and this could generate troubles.
Replace also uses of assert() with __ASSERT_NO_MSG() in nrfx driver
shims that use this macro without including the corresponding header
file (i.e. that implicitly rely on assert.h being included from
nrfx_glue.h, which is no longer the case).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Current implementation directly passes timeout value to workqueue/timer
which results in assertion or instant timeout in case when K_FOREVER is
passed. This fix ensures that no timer or workqueue is called with
K_FOREVER.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Extended nrf_uarte driver to support TX only UARTE instances.
When RX pin is not provided then RX is not started at all. This
allows to achieve low power with logging/console enabled.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Nrfx_uarte uses a hardware timer/counter to count received bytes.
Keeping this timer enabled increases power consumption for some SoCs.
This change disables the timer when an inactive power state is set.
Signed-off-by: Audun Korneliussen <audun.korneliussen@nordicsemi.no>
calling UARTE power management with DEVICE_PM_SUSPEND_STATE
then DEVICE_PM_OFF_STATE causes a deadlock in while loop.
It waits for an event witch never comes
Signed-off-by: Ismael Fillonneau <ismael.fillonneau@stimio.fr>
Cleanup around COND_CODE_1 usage and replacing with
IF_ENABLED if applicable.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Add clearing error event to UART and UARTE drivers.
Without it driver goes into infinite interrupt loop.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
There is possibility that endrx interrupt will be triggered in the
middle of timer interrupt responsible for UARTE timeout, this
patch handles this case.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Update calls to nrfx HAL functions to reflect API changes introduced in
nrfx 2.0.0. All these functions are now called with the first parameter
pointing to the structure of registers of the relevant peripheral.
Also a few functions got renamed:
- nrf_gpiote_int_is_enabled to nrf_gpiote_int_enable_check
- nrf_gpiote_event_is_set to nrf_gpiote_event_check
- nrf_rng_event_get to nrf_rng_event_check
- nrf_rng_int_get to nrf_rng_int_enable_check
- nrf_rtc_event_pending to nrf_rtc_event_check
- nrf_rtc_int_is_enabled to nrf_rtc_int_enable_check
- nrf_timer_cc_read to nrf_timer_cc_get
- nrf_timer_cc_write to nrf_timer_cc_set
Default configuration values were removed from nrfx_config files,
so the drivers pwm_nrfx and spi_nrfx_spis no longer can use those.
Function nrfx_pwm_init() now takes one more parameter - context pointer
that is passed to the event handler, not used in the pwm_nrfx driver.
HALs for UART and UARTE now allow configuration of the parity type
and the number of stop bits, for SoCs that provide the corresponding
registers.
Signed-off-by: Karol Lasończyk <karol.lasonczyk@nordicsemi.no>
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
In some applications where power management is used, it is not expected
that the GPIO pins of the UARTE is reconfigured upon power state change.
Added a Kconfig option to disable the UARTE driver management of GPIOs.
It defaults to y in order to not affect current behavior unless the user
configures it specifically.
Signed-off-by: Dennis Wildmark <dennis.wildmark@assaabloy.com>
Use the int_literal_to_timeout Coccinelle script to convert literal
integer arguments for kernel API timeout parameters to the standard
timeout value representations.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
nrf52840 and nrf9160 have possible configuration of two stop bits
for UART and UARTE, this commit adds handling of it to driver.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Configure pins before enabling and after disabling UARTE through
power management functions.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Ensure that two routines won't interfere with eachother.
In current situation there is possibility that ENDRX will be called
during rx_timeout routine or vice-versa which will result in wrong
offset and length passed to user.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Due to longer than expected user callback handling, rx byte counting
got out of sync with real values. It leads to incorrect values
reported to user. This fix adds sync point at the end of buffer.
When using hardware rx counting this issue should not occur.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
move misc/util.h to sys/util.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move uart.h to drivers/uart.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The defines should have had a _0 on them, now that we generate the
proper defines, fixup the cases that used that old scheme.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
If reception was longer than rx timeout, UART_RX_RDY event
would provide data with delay, and synchronise at buffer end.
This change makes sure that all data is given to user when timeout
occurs.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Without first triggering TASKS_STOP{RX,TX}, I observed that the UARTE
was never disabled when using device_set_power_state which resulted in
the HFCLK never being shut down and several hundred microamps in
unnecessary current consumption when idle. This seems to fix the issue.
Also added special treatment of uarte if CONFIG_UART_ASYNC_API is
selected. Note that the #ifdef isn't enough, since it's possible that
the option is set, but only one of the UARTs uses it.
Signed-off-by: Benjamin Lindqvist <benjamin.lindqvist@endian.se>
Bad order of interrupt calls made it unable to transmitt data
using interrupt driven API.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Rename reserved function names in drivers/ subdirectory. Update
function macros concatenatenating function names with '##'. As
there is a conflict between the existing gpio_sch_manage_callback()
and _gpio_sch_manage_callback() names, leave the latter unmodified.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
