There's no need for debug logs by default in the mesh sample, and it
just contributes excessively to the ROM footprint.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Move to using the generated IRQ defines from the DTS instead of soc.h.
This change also fixes a minor bug in that the error irq priority wasn't
getting correctly picked up from device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This PR enables Bluetooth stack if Bluetooth L2 is
compiled in.
Change-Id: I8f8127031140f0603615af44e0809d203db32f48
Signed-off-by: Wojciech Bober <wojciech.bober@nordicsemi.no>
If the network interface is down, then IPv6 DAD (Duplicate
Address Detection) cannot be done if new IPv6 address is added
to the network interface. This can happen in Bluetooth, where
network interface is taken up only after there is a BT connection.
The DAD is delayed and done later after the network interface is up.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Normally network interface is always UP, but Bluetooth
interfaces are down until connected. So if this is the case,
then check the interface status before trying to access variables
that are NULL. This was seen with "net iface" shell command when
BT was enabled.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Not easily done using RAM/ROM filters, configurations need to be adapted
to make this fit on more devices. Limit the target platforms now while
we figure out configurations.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
In case the application is using NET_L2_BLUETOOTH the SLIP drivr shall
not be selected as bus they cannot coexist since they use the same UART
port:
arch/x86/soc/ia32/Kconfig.defconfig:
config BLUETOOTH_UART_ON_DEV_NAME
default "UART_1"
config UART_PIPE_ON_DEV_NAME
default "UART_1"
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch allows the use of the MCR20A driver with KW2xD devices.
The clock output of the transceiver can be used as an input clock
for the PLL of the SoC. The hardware reset and CLK_OUT setup of
the transceiver should then be performed during the initialization
of the SoC. The driver is not allowed to do it again.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Some patches have been lost during rebase before the initial commit,
this path fixes it.
- correct copyright in registers definition header file
- fix undefined macro inside CLK_OUT configuration
- use the return value of k_sem_take if there is a timeout
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
This is a configuration that is unrealistic and used only to verify
Kconfig dependencies, trying to build this for every board fails due to
size limitations and due to unavailable device support on some of those
boards, building for qemu targets should be good enough.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Following rework of pinmux driver for whole stm32 family,
remove call to stm32_get_pin_config which is no more
used.
Include dt-bindings stm32-pinctrl.h file to ensure coherency
between dts files and pinmux driver.
Due to change of "port" from enum to a series of define
(enum not accepted as dt binding), rework gpio_stm32_config
declaration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add needed uart pinctrl configuration in pinmux node.
Populate stm32 f1 based boards dts files with references
to uart pinctrl nodes
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add needed uart pinctrl configuration in pinmux node.
This is done thanks to <soc>-pinctrl.dtsi file matching
<soc>.dtsi files
Populate stm32 f3 based boards dts files with references
to uart pinctrl nodes
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add needed uart pinctrl configuration in pinmux node.
This is done thanks to <soc>-pinctrl.dtsi file matching
the <soc>.dtsi files
Populate stm32 f4 based boards dts files with references
to uart pinctrl nodes.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32F3 pinmux handler is reworked to support future pinmux dts
generation.
Preliminary change is done to move pin configuration
informations in a {pin, conf} structure closer to dts fields
"pins" array is removed as information is transfered to
"pinconf" array
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32F4 pinmux handler is reworked to support future pinmux dts
generation.
Preliminary change is done to move pin configuration
informations in a {pin, conf} structure closer to dts fields
"pins" array is removed as information is transfered to
"pinconf" array
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Rework stm32f1 pinmux code for future dts based pinmux code
generation.
Pin configuration is now done directly thanks to gpio port
configuration. Reference to pseudo alternate functions are
now removed same as the use of pins[] array.
Pins function (uart tx for instance) is set implicitly by
defining gpio mode and configuration.
This behavior is specific to stm32f10x series.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add pinctrl node on stm32l4 soc dts files, including uart
pinctrl configurations. This is done thanks to <soc>-pinctrl.dtsi
file matching the <soc>.dtsi file
Populate stm32 l4 based boards dts files with references
to uart pinctrl nodes
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32L4 pinmux handler is reworked to support future pinmux dts
generation.
Preliminary change is done to move pin configuration
informations in a {pin, conf} structure closer to dts fields
"pins" array is removed and information is transferred to
"pinconf" array
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add pinmux yaml file and bindings before introduction
of pinmux node in stm32 soc device tree files
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
For CONFIG_UART_PIPE_ON_DEV_NAME the chosen property is
"zephyr,uart-pipe" not ""zephyr,bt-mon-uart".
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We have the same pattern for how we map a chosen property to the device
label that generates a Kconfig define. Rather than duplicating the code
over and over again, lets just iterate over a list of defines and chosen
properties. This also provides us a list we can use in the future to
special case handle the defines associated with names.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In many networking tests we had to configure SLIP in the prj.conf
leaving those configurations Qemu specific. This change enables SLIP for
QEMU targets automatically and allows reuse of prj.conf for multiple
boards.
Additionally, the TUN options is removed. This option was not used
anywhere.
To enable self-contained networking tests that do not depend on SLIP, we
introduce the new option NET_TEST which disables TAP and allows testing
in QEMU without the need for a host interface.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
In L4 series, select HAS_STM32CUBE is done per soc.
This could be factorized in Kconfig.series.
Aim is to lower the steps to add a new SoC.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The ethernet HAL has a different uint32_t typedef than Zephyr's u32_t:
uint32_t in the HAL is long unsigned int, while in Zephyr it's
unsigned int. This is causing a build warning on GCC ("warning:
passing argument 2 of ‘ENET_GetRxFrameSize’ from incompatible pointer
type") when passing a u32_t* where ENET_GetRxFrameSize expects a
uint32_t*.
Add a cast to silence the warning.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
* Fix the indentation which was caused by uint32_t -> u8_t changes.
* Make sure there is no unused variable warning if debugging is
enabled but debug level is low.
* Add assert that checks that Imax_abs is > 0 which it should be.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The Imax doublings value was too large which caused overflow
of Imax_abs value, which then could cause Trickle test to fail.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This will allow checking if we are building for QEMU globally, without
having to know the exact architecture and board name.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
patch fix the build warning generated while building
application for quark_d2000. This is a fix for Jira ZEP-2437
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
This patch fixes following error of python script.
TypeError: cannot use a string pattern on a bytes-like object
Jira: ZEP-2290
Signed-off-by: Punit Vara <punit.vara@intel.com>
The majority of these fixes adjust the memory limit needed to build the
various tests on systems with and without BLE support. We also fixup
one test case that was able to run on platforms with 16k of memory.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
If there are no neighbors or there is no route to one specific
neighbor, then check the NULL pointer before accessing the route.
This issue was seen with "net route" shell command.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The net_stack_analyze function wants to look at the stack buffer,
but it is making assumptions on where this data is that are no
longer valid. Change to use the proper APIs for referencing this.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
When we introduced I2C DTS support on hexiwear_kw40z we got it wrong.
Its I2C1 not I2C0 that was being used on the hexiwear. Fix the dts and
fixup file to reflect that.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
