This adds a new config option for SAM0 targets that use the BOSSA
bootloader. If the CDC ACM driver is also enabled, then the
programmer can automatically reset the board into the bootloader for
programming.
Signed-off-by: Michael Hope <mlhx@google.com>
The optional SOC_CONTEXT carries processor state registers that need to
be initialized properly to avoid uninitialized memory read as processor
state.
In particular on the RV32M1 the extra soc context stores a state for
special loop instructions, and loading non zero values will have the
core assume it is in a loop.
Signed-off-by: Karsten Koenig <karsten.koenig.030@gmail.com>
Saving an extended context for RV32M1 should be optional, but it was
broken due to the offset calculation not taking the according option
into account.
Signed-off-by: Karsten Koenig <karsten.koenig.030@gmail.com>
x19 is callee saved register. z_arch_el3_plat_init being a callee,
it should save it before using it. However, at this point, stack
has not been setup. So, let's just use x20 instead which is not
being used caller yet. This bug was causing VBAR_EL1 corruption,
but since [10:0] bits are reserved, bug was hidden.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
The `TEXT_SECTION_OFFSET` symbol is used to specify the offset between
the beginning of the ROM area and the address of the first ROM section.
This commit renames `TEXT_SECTION_OFFSET` to `ROM_START_OFFSET` because
the first ROM section is not always the `.text` section.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
In case of dualcore, STM32H7, STM32W and STM32MP1,
protect concurrent register write access with HSEM.
Done for following drivers:
clock_control, counter, flash, gpio, interrupt_controller
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
Various cleanups to the x86 early serial driver, mostly with the goal
of simplifying its deployment during board bringup (which is really
the only reason it exists in the first place):
+ Configure it =y by default. While there are surely constrained
environments that will want to disable it, this is a TINY driver,
and it serves a very important role for niche tasks. It should be
built always to make sure it works everywhere.
+ Decouple from devicetree as much as possible. This code HAS to work
during board bringup, often with configurations cribbed from other
machines, before proper configuration gets written. Experimentally,
devicetree errors tend to be easy to make, and without a working
console impossible to diagnose. Specify the device via integer
constants in soc.h (in the case of IOPORT access, we already had
such a symbol) so that the path from what the developer intends to
what the code executes is as short and obvious as possible.
Unfortunately I'm not allowed to remove devicetree entirely here,
but at least a developer adding a new platform will be able to
override it in an obvious way instead of banging blindly on the
other side of a DTS compiler.
+ Don't try to probe the PCI device by ID to "verify". While this
sounds like a good idea, in practice it's just an extra thing to get
wrong. If we bail on our early console because someone (yes, that's
me) got the bus/device/function right but typoed the VID/DID
numbers, we're doing no one any favors.
+ Remove the word-sized-I/O feature. This is a x86 driver for a PCI
device. No known PC hardware requires that UART register access be
done in dword units (in fact doing so would be a violation of the
PCI specifciation as I understand it). It looks to have been cut
and pasted from the ns16550 driver, remove.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
When building for nRF5340 PDK board, enable Kconfig option
for Erratum 19. Do not enable when building on nRF5340 DK.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Add and mark PCIe highmem outbound memory as nGnRnE device memory
in Viper SoC MMU configuration.
Increase VA/PA bits to 36-bits to support the same.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
ZEPHYR_SDK_INSTALL_DIR will be set as an internal CMake variable when
using the Zephyr SDK.
The Zephyr SDK zephyr/host-tools.cmake will ensure to set the CMake
ZEPHYR_SDK_INSTALL_DIR variable to the environment setting, or the
install directory in case the CMake package was used.
Users not using the environment variable will experience the following
error:
```
Linking C executable zephyr/.../bootloader/bootloader.elf
FAILED: zephyr/.../bootloader/bootloader.elf
<path>/xtensa-zephyr-elf/bin/ld: cannot find -lhal
```
This commit ensures code build correctly both when setting the
environment variable ZEPHYR_SDK_INSTALL_DIR, and when using Zephyr SDK
CMake `find_package(Zephyr-sdk)`
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
This patch introduces the support of low power modes
for the STM32WBxx from STMicroelectronics based on the lptim
Here, the power modes are sleep modes have lptimer as wakeup source.
The sleep modes are configured by the SYS_POWER_MANAGEMENT.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add initial support for nuvoton numicro m48x SoC series, basic
init and uart functionality are covered with gpio and clock
directly relies on HAL.
Signed-off-by: Saravanan Sekar <saravanan@linumiz.com>
This enables PWM and connects it to the main LED. Tested by running
samples/basic/blinky_pwm and /fade_led.
Signed-off-by: Michael Hope <mlhx@google.com>
The SAM0 Timer/Counter for Control Applications can act as a counter
or generator. Add a binding for the TCC in PWM mode and helper to
check the compat mode.
Signed-off-by: Michael Hope <mlhx@google.com>
Add reset interrupt handlers for all three types of reset
interrupts that iProc PCIe EP can receive - namely PERST,
INB PERST and FLR.
Signed-off-by: Shivaraj Shetty <shivaraj.shetty@broadcom.com>
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Change the SAM0 to match other boards by selecting the SAM0 specific
driver when a driver class is selected.
For example, automatically enable CONFIG_SPI_SAM0 when CONFIG_SPI is
enabled.
Signed-off-by: Michael Hope <mlhx@google.com>
Only boards with at least 64K Flash will activate MPU because:
MPU + UERSPACE + All switches implicity activated
(CONFIG_MPU_STACK_GUARD, CONFIG_ARM_STACK_PROTECTION ...)
will consume about 40K Flash
(value computed on nucleo_f767_zi on tests/arch/arm/arm_ramfunc/).
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
The PWM drivers has been refactored using the HAL LL API. Not only that,
but the set pin_set function is now faster, as channel output compare is
just initialized if needed.
NOTE: Has been tested using H743zi board for now.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Previously, DTS specification of physical RAM bounds did not
correspond to the actual bounds of system RAM as the first
megabyte was being skipped.
There were reasons for this - the first 1MB on PC-like systems
is a no-man's-land of reserved memory regions, but we need DTS
to accurately capture physical memory bounds.
Instead, we introduce a config option which can apply an offset
to the beginning of physical memory, and apply this to the "RAM"
region defined in the linker scripts.
This also fixes a problem where an extra megabyte was being
added to the size of system RAM.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Introduced interface for efficient logging from external logsystems:
Added handling of vaargs and automatic strdup to macros intended
to be used in logging interface function. Fast path to less then 4
arguments to speed up the execution. Made log_count_args external,
if external logsystem cannot count arguments.
Signed-off-by: Tomasz Konieczny <tomasz.konieczny@nordicsemi.no>
Those MCUs have 2KB RAM and 16KB FLASH memory, but they are still
powerful enough to run small configuration of Zephyr RTOS.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Added / Tested support for RNG on the STM32F767ZI nucleo board.
Updated the SoC defconfig to auto-enable the driver when
ENTROPY_GENERATOR is enabled, and updated the board README.
Signed-off-by: Bilal Wasim <bilalwasim676@gmail.com>
- Change default CPU Clock to 240MHz
(PLL is activated)
- I2C, UART will use sysclk from clock driver
- esp32_enable_peripheral replaced by
clock_control_on
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
- Support PLL for Higher Frequencies 80,160,240 MHz
- Support XTAL Frequencies 26MHz, 40MHz
- Clock Driver can't be disabled, because all of the other drivers
will depend on it to get their operating Frequency based on chosen
clock source (XTAL/PLL).
- Add needed references to BBPLL i2c bus ROM functions.
- Add `rtc` node to Device Tree.
- Since All Peripherals Frequency is depending on CPU_CLK Source,
`clock-source` property added to CPU node
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
This patch introduces the support of low power modes
for the STM32L4xx from STMicroelectronics based on the lptim
Here, the power modes are sleep modes with lptimer as wakeup.
Depending on the SYS_POWER_MANAGEMENT configuration.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
tested on mimxrt1060_evt
MEMORY_NOCACHE is needed
test on frdmk64f
special test slot need configure with
CONFIG_DMA_TEST_SLOT_START
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
Remove Kconfig, linker script, and related bits associated with
CUSTOM_RODATA_LD, CUSTOM_RWDATA_LD, CUSTOM_SECTIONS_LD,
SOC_NOINIT_LD, SOC_RODATA_LD, and SOC_RWDATA_LD options that have been
deprecated since Zephyr 2.2.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This option controls whether additional BLE support is
enabled for the cc13xx_cc26xx platform in hal/ti and
subsys/bluetooth.
Signed-off-by: Christopher Friedt <chrisfriedt@gmail.com>
Introduce switch to allow board configuration for VCI pins to
remain HW-controled depending on the design.
Currently pins are always configured as GPIOs which is not always
desirable.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
The NXP's Kinetics K66F is able to run with max frequency of 180MHz.
To achieve this goal the SMC's PMPROT and PMCTRL registers need to be
adjusted.
On the contrary the K64F doesn't support HSRUN run mode.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This option enables support for High Speed RUN operation mode for
K66F. The K64F SoC doesn't support this mode.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Add the necessary clock configuration to support STM32L-based
SoCs. This change likely adds support for other STM32 SoCs as well
since the HSI48 clock is configured for all SoCs that support it
(except the STM32L4x) instead of just the STM32G4X.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
emsdp_em7d_esp is a board with secure just like em_starterkit_em7d,
but the secure feature not configed in defconfig file. we need to add
below configs in emsdp_em7d_esp_defconfig files:
CONFIG_ARC_HAS_SECURE=y
CONFIG_TRUSTED_EXECUTION_SECURE=y
when secure feature enabled, we use secure timer for system tick, so
we need to add below macro for secure timer:
#define IRQ_SEC_TIMER0 20
Signed-off-by: Watson Zeng <zhiwei@synopsys.com>
This commit fixes Cortex-M header inclusions from the deprecated paths.
The Cortex-M headers were relocated from `include/arch/arm/cortex_m` to
`include/arch/arm/aarch32/cortex_m` by the refactoring done in the
commit d048faacf2.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Now when we're finally ready to open QEMU port for ARC
we introduce the first ever platform it supports and in fact does
that quite well - Zephyr RTOS.
For now we only offer support of basic EM & HS code execution,
built-in timers, interrupt controller and set of very simple
peripherals: DW UART & optionally MMIO Virtio devices.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
