This commit adds support for the Zynq UltraScale+ MPSoC as a qemu based
platform for Cortex-R based testing. This SoC only supports an
interrupt controller and serial port for limited testing.
Signed-off-by: Bradley Bolen <bbolen@lexmark.com>
The GIC400 is a common interrupt controller that can be used with the
Cortex A and R series processors. This patch adds basic interrupt
handling for the GIC, but does not handle multiple routing or
priorities.
Signed-off-by: Bradley Bolen <bbolen@lexmark.com>
Remove unused "system-clock-frequency" property, we don't have this
defined in various bindings and thus aren't using it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add "#address-cells" and "#size-cells" to the fixed-partition binding as
these are properties that may existing in the fixed-partition node.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
* Change pwm device bindings to include both base and pwm.yaml. This
allow for flexibility for any nodes that might not need/utilize the
base binding.
* Added pwm.yaml to a few device bindings that were missing it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Introduce a clock.yaml that clock controller bindings should inherit
from. clock.yaml defines the properties "#clock-cells" which all
clock controllers should have.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Introduce a gpio.yaml that GPIO controller bindings should inherit
from. gpio.yaml defines the properties "gpio-controller" and
"#gpio-cells" which all gpio controllers should have.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Introduce a intc.yaml that interrupt controller bindings should inherit
from. intc.yaml defines the properties "interrupt-controller" and
"#interrupt-cells" which all interrupt controllers should have.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This is to support e.g. "<&adc 3>" in the device tree to create e.g.
DT_FOO_IO_CHANNELS_CONTROLLER = "ADC_0"
DT_FOO_IO_CHANNELS_INPUT = 3
Signed-off-by: Jim Paris <jim@jtan.com>
The nxp,kinetis-sim is shared by 2 SoC familes and on one of them
its not used for clocks. As such that SoC will not have a #clock-cells
property so mark it optional.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The binding for st,stm32-timers specifies #address-cells and #size-cells
as required but no dts files that have st,stm32-timers specify these
properties. Remove them from the binding.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This emulates a RISC-V in 64-bit mode on a SiFive FE310 dev board.
Memory is tight so a few tests had to be disabled due to the extra
memory usage compared to qemu_riscv32.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Use clock specified in the device tree for obtaining the source clock
frequency for the pwm_mcux_ftm driver instead of relying on having an
NXP Kinetis MCG clock available in all SoCs supporting FlexTimer (FTM)
modules.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This adds a driver for st7789v lcd controller, and TL019FQV01 lcd.
The bulk of the driver is based on the existing ili9340 driver.
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
NRF_UICR needs to be defined for nRF9160 SoC in
nrfx_config_nrf9160.h, because it is not defined
in nrfx/hal/mdk/nrf9160.h (as it is a Secure-only
peripheral).
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
- update doc for different core configuration.
- fix some bugs in dts related files.
- add dts config and defconfig for different core configuration.
- end files with a newline in boards/arc/emsdp/board.dtsi
- remove unused head in boards/arc/emsdp/doc/index.rst
- ARC_MPU_VER in different core is fixed. so remove some useless code
for ARC_MPU_VER judgements in Kconfig.defconfig.* files for emsdp
Signed-off-by: Watson Zeng <zhiwei@synopsys.com>
The snps,designware-intc.yaml and xtensa,intc.yaml define a required
property snps,num-irq-priority-bits that isn't defined in any .dts
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
After witnessing some strange errors with memory not being
what it should be, lifiting everything above 1MB has solved
it. The Zephyr binary was being loaded into memory containing
reserved regions, resulting in data corruption.
We still simulate XIP for testing purposes by setting up the
memory map as follows:
0x000000 - 0x0FFFFF : Non-present
0x100000 - 0x4FFFFF : "Flash" ROM region
0x500000 - 0x8FFFFF : "SRAM" RAM region
For a total of 9 megabytes of physical RAM used.
Fixes problems observed in some large tests when code coverage
is enabled (which increases the amount of RAM used even more).
Fixes: #17782
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
With the new DT checks the dts bindings for "nxp,flexpwm" and
"nxp,imx-pwm" had old conventions that we now treat as build errors.
Additionally fix the number of #pwm-cells for "nxp,imx-pwm" to be 1.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
i.MX RT10XX processors have four eFlexPWM modules, each containing
four 2-channels PWM submodules.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
The true mmio-sram nodes should not have had a 'device_type' property.
Remove it from the cases that we clearly know are SRAM.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The true mmio-sram nodes should not have had a 'device_type' property.
Remove it from the cases that we clearly know are SRAM.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The "{d,i}ccm" nodes should not have had a 'device_type' property.
Remove it from the cases that we clearly know are {d,i}ccm.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The true mmio-sram nodes should not have had a 'device_type' property.
Remove it from the cases that we clearly know are SRAM.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This dts binding file remained out from 0ec0c84808 commit, because
it was still in the pre-merging status.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
With the upcoming riscv64 support, it is best to use "riscv" as the
subdirectory name and common symbols as riscv32 and riscv64 support
code is almost identical. Then later decide whether 32-bit or 64-bit
compilation is wanted.
Redirects for the web documentation are also included.
Then zephyrbot complained about this:
"
New files added that are not covered in CODEOWNERS:
dts/riscv/microsemi-miv.dtsi
dts/riscv/riscv32-fe310.dtsi
Please add one or more entries in the CODEOWNERS file to cover
those files
"
So I assigned them to those who created them. Feel free to readjust
as necessary.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Add a new sifive,plic-1.0.0 binding that inherits from the riscv,plic0
binding. The new binding adds a required riscv,ndev property, which
gives the number of external interrupts supported.
Use the new binding for microsemi-miv.dtsi (with a value of 31 for
riscv,ndev, from http://www.actel.com/ipdocs/MiV_RV32IMAF_L1_AHB_HB.pdf)
and riscv32-fe310.dtsi (which already assigns riscv,ndev).
Also remove a spurious riscv,ndev assignment from
riscv32-litex-vexriscv.dtsi.
Also make edtlib and the old scripts/dts/ scripts replace '.' in
compatible strings with '_' when generating identifiers.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Trying to get rid of properties that appear on device tree nodes but
aren't declared in bindings.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Trying to get rid of properties that appear on device tree nodes but
aren't declared in bindings.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Trying to get rid of properties that appear on device tree nodes but
aren't declared in bindings.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
These are not declared in dts/bindings/arm/nxp,kinetis-sim.yaml and do
not generate any output.
Trying to get rid of properties that appear on device tree nodes but
aren't declared in bindings.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
A minor spelling fix in an inline comment in
both nRF9160 Secure and Non-Secure .dtsi headers.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
These are not declared in any binding and do not generate any output.
Trying to get rid of properties that appear on device tree nodes but
aren't declared in bindings.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Fix the following dtc warning:
mimxrt1064_evk.dts.pre.tmp:78.31-85.5: Warning (spi_bus_bridge):
/soc/flexspi1@402a4000: node name for SPI buses should be 'spi'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Several aliases were added to nrf9160[ns].dtsi files solely for
the purpose of getting base addresses of certain hardware modules
via DT_ macros generated for these aliases.
Since for one-instance modules the same can be now achieved with
standard DT_INST_0_* macros, there is no need to keep these aliases.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
