Add option to concatenate i2c transfers. If concatenation buffer size is
provided then transfers will be concatenated as long as there is space
left in buffer.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Rework the devicetree to utilize new DT_INST macros and extract per
instance data for clocks and dma from devicetree. We update the
atmel,sam0-i2c binding for dma to replace the dma property with
proper 'dmas' property.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add support for the GCLK, MCLK, and PM clock controllers. Add bindings
and devicetree nodes associated with these clock controllers. Also add
clock references for the SERCOM peripheral set to allow those drivers
(i2c, spi, uart) to utilize this information.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add pinctl support for the SAM TWI and TWIHS I2C devices. We update
the TWI and TWIHS I2C bindings to have pinctrl-0 bindings that are
expected to have 2 phandles to the TWCK & TWD pinctrl nodes.
The pinctrl nodes will have an 'atmel,pins' property that describes the
GPIO port, pin and periphal configuration for that pin.
We update sam*-pinctrl.dtsi files with all the various pin ctrl
configuration operations supported by the given SoC family. These
files are based on data extracted from the Atmel ASF HAL
(in include/sam<FAMILY>/pio/*.h).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The flexcomm peripheral on lpc socs can be configured into uart, spi,
i2c, or i2s mode. Introduce a shared device tree binding that gets
included by the more specific driver type bindings.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds i2c device tree bindings and nodes for the lpc54xxx and lpc55s6x
socs in preparation for adding a new i2c driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This adds I2C bitbang driver for LiteX SoC builder with its bindings.
Signed-off-by: Robert Winkler <rwinkler@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Add any useful information from 'title:' to the 'description:' strings
(e.g. explanations of acronyms), and remove 'title:' as well as any
copy-pasted "this binding gives a ..." boilerplate.
Also clean some description strings up a bit.
Some other things could probably be cleaned up (replacing 'GPIO node'
with 'GPIO controller' on controllers for consistency, for example), but
I kept things close to the original to avoid accidentally messing up.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Add property for specifying the bus idle timeout for the NXP
i.MX/Kinetis LPI2C I2C controller.
Enabling the bus idle timeout helps the controller to recover from
e.g. EMC causing false clock pulses/spikes on the SCL line.
Without a timeout the LPI2C controller will assume that another bus
master took over the I2C bus and thus refuses to issue a I2C START
condition.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
With https://github.com/zephyrproject-rtos/zephyr/pull/20185, multi-line
descriptions will be formatted nicely, but using '>' breaks it, because
it removes internal newlines (including between paragraphs).
See https://yaml-multiline.info/.
Replace 'description: >' with 'description: |' to encourage '|'. That'll
prevent '>' from getting copied around and messing up long descriptions.
This will lead to some extra newlines in the output, but it's fine.
Line-wrapping messes up any manual formatting.
The replacement was done with
$ git ls-files 'dts/bindings/*.yaml' | \
xargs sed -i 's/description:\s*>/description: |/'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This commit introduces separate "compatible" strings for dts nodes
representing different types of Nordic TWI peripherals. Previously
"nordic,nrf-i2c" was used for both TWI and TWIM, and TWIS was not
supported.
Quite a few files need to be touched by this commit but the changes can
be divided into groups of related or very similar ones, distinguishable
by the initial part of the path to the modified file:
* dts/bindings/i2c/
new bindings for "nordic,nrf-twim" and "nordic,nrf-twis" are added
and the one for "nordic,nrf-i2s" is renamed to "nordic,nrf-twi",
common fields for all these bindings are extracted to a shared file
* dts/arm/nordic/
"compatible" properties in i2cX nodes are updated (when there is no
choice as only one type of TWI peripheral is available) or replaced
with a comment pointing out that the proper type of peripheral needs
to be picked at some upper layer
* drivers/i2c/
both flavors of i2c_nrfx drivers are updated with the new names of
macros generated from dts
* boards/
all i2cX nodes in dts files for boards equipped with an nRF chip are
updated with the proper "compatible" property, according to the type
of TWI peripheral that is currently selected for the board by the
corresponding Kconfig choice option (I2C_x_NRF_TWI*)
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The arc_iot.dtsi used "intel,qmsi-ss-gpio" and "intel,qmsi-ss-i2c"
compatiables, however we have no drivers for these and it seems wrong
that the ARC platform would utilize such compatiables. Remove the
compatiable fields for now (proper one's can be added when there are I2C
and GPIO drivers for this platform).
Also remove the binding files associated with "intel,qmsi-ss-gpio" and
"intel,qmsi-ss-i2c" as nothing in tree utilizes them.
Fixes: 19227
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Instead of
child:
bus: foo
parent:
bus: bar
, have
child-bus: foo
parent-bus: bar
'bus' is the only key that ever appears under 'child' and 'parent'.
Support the old keys for backwards compatibility, with a deprecation
warning if they're used.
Also add 'child/parent-bus' tests to the edtlib test suite. It was
untested before.
I also considered putting more stuff under 'child' and 'parent', but
there's not much point when there's just a few keys I think. Top-level
stuff is cleaner and easier to read.
I'm planning to add a 'child-binding' key a bit later (like 'sub-node',
but more flexible), and child-* is consistent with that.
Also add an unrelated test-bindings/grandchild-3.yaml that was
accidentally left out earlier.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
For quite a few peripherals that are currently supported by nrfx HALs
or drivers there are no definitions of corresponding CMSIS-Core
peripheral accessing symbols that would provide their base addresses
in the proper domain (secure or non-secure), accordingly to the build
target. This commits adds devicetree nodes for these peripherals so
that their base addresses can be used in definitions of the accessing
symbols mentioned above.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Instead of
properties:
compatible:
constraint: "foo"
, just have
compatible: "foo"
at the top level of the binding.
For backwards compatibility, the old 'properties: compatible: ...' form
is still accepted for now, and is treated the same as a single-element
'compatible:'.
The old syntax was inspired by dt-schema (though it isn't
dt-schema-compatible), which is in turn a thin wrapper around
json-schema (the idea is to transform .dts files into YAML and then
verify them).
Maybe the idea was to gradually switch the syntax over to dt-schema and
then be able to use unmodified dt-schema bindings, but dt-schema is
really a different kind of tool (a completely standalone linter), and
works very differently from our stuff (see schemas/dt-core.yaml in the
dt-schema repo to get an idea of just how differently).
Better to keep it simple.
This commit also piggybacks some clarifications to the binding template
re. '#cells:'.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The 'category: required/optional' setting for properties is just a
yes/no thing. Using a boolean makes it clearer, so have
'required: true/false' instead.
Print a clear error when 'category:' is used:
edtlib.EDTError: please put 'required: true' instead of 'category:
required' in 'properties: foo: ...' in
test-bindings/sub-node-parent.yaml - 'category' has been removed
The old scripts in scripts/dts/ ignore this setting, and only print a
warning if 'category: required' in an inherited binding is changed to
'category: optional'. Remove that code, since the new scripts already
have the same check.
The replacement was done with
git ls-files 'dts/bindings/*.yaml' | xargs sed -i \
-e 's/category:\s*required/required: true/' \
-e 's/category:\s*optional/required: false/'
dts/binding-template.yaml is updated as well.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Renaming bindings to consistently be called foo-controller.yaml for
controllers and foo-device.yaml for devices (last one mostly makes sense
for devices on buses and the like).
I was thinking of having a plain foo.yaml be the controller as well, but
!include interrupt.yaml
reads much worse than
!include interrupt-controller.yaml
Another advantage of this approach is that no binding changes meaning
(which could be risky). It's just adding suffixes to filenames.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Sanity-checking each !included file separately was inherited from the
old scripts. It makes it messy to check that combinations of fields make
sense, e.g. to check 'const:' or 'default:' against 'type:', since those
fields might come from different files (this is handy, since it makes
sense to just add/change a 'const:' value, for example).
Drop the requirement that each !included file is a complete binding in
itself, and treat them as binding fragments instead. Only check the
final merged binding.
This also means that !included files no longer need to have a
'description:' or 'title:' (those have always been unused for !included
files), so remove those, and add comments that explain what the
fragments are for instead. That should demystify bindings a bit.
Also fix the descriptions of i2c.yaml, i2s.yaml, spi.yaml, and
uart.yaml. They're for controllers, not devices. These are copy-paste
error from the corresponding device .yaml files.
Piggyback some indentation consistency nits in binding-template.yaml.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
* Add "#address-cells" and "#size-cells" to base.yaml as properties
that can exist on any node. Cleanup other bindings that inherit
from the base.yaml.
* Add "status" property with an enum of valid options.
* Add "interrupt-parent" to base.yaml. It's a phandle to the node
which is the interrupt controller for the interrupt.
* Add "interrupt-extended" to base.yaml. Provides a way to specify
an interrupt-parent and specifier in a single property. Useful if
a device has multiple interrupts in which different interrupts go
to different interrult controllers.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In most cases #<FOO>-cells should be a constant. For example in spi
controller #address-cells should be 1, and #size-cells should be 0.
Use the const attribute to specify such single known values. Add const
value to missing bindings which have cells.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
No binding has anything but 'version: 0.1', and the code in scripts/dts/
never does anything with it except print a warning if it isn't there.
It's undocumented what it means.
I suspect it's overkill if it's meant to be the binding format version.
If we'd need to tell different versions from each other, we could change
some other minor thing in the format, and it probably won't be needed.
Remove the 'version' fields from the bindings and the warning from the
scripts/dts/ scripts.
The new device tree script will give an error when unknown fields appear
in bindings.
The deletion was done with
git ls-files 'dts/bindings/*.yaml' | xargs sed -i '/^\s*version: /d'
Some blank lines at the beginning of bindings were removed as well.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The port_sel property had the category set to 'define' which isn't a
valid option. Change it to be 'required'.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
A number of dts bindings mark 'interrupts' as a required property when
in fact they are not for those devices. Remove the 'required' setting
and just have 'interrupts' as 'optional'.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Setting it seems rare. Maybe it could be changed to required on just
some platforms (!including bindings can change 'optional' to
'required').
Fixes a bunch of errors in
https://github.com/zephyrproject-rtos/zephyr/issues/17532.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Now that the generation script doesn't look at the "generation" in the
YAML, we can remove it from the binding files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
YAML document separators are needed e.g. when doing
$ cat doc1.yaml doc2.yaml | <parser>
For the bindings, we never parse concatenated documents. Assume we don't
for any other .yaml files either.
Having document separators in e.g. base.yaml makes !include a bit
confusing, since the !included files are merged and not separate
documents (the merging is done in Python code though, so it makes no
difference for behavior).
The replacement was done with
$ git ls-files '*.yaml' | \
xargs sed -i -e '${/\s*\.\.\.\s*/d;}' -e 's/^\s*---\s*$//'
First pattern removes ... at the end of files, second pattern clears a
line with a lone --- on it.
Some redundant blank lines at the end of files were cleared with
$ git ls-files '*.yaml' | xargs sed -i '${/^\s*$/d}'
This is more about making sure people can understand why every part of a
binding is there than about removing some text.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Move common properties like 'compatible', 'reg', 'reg-names',
'interrupts', 'interrupt-names', and 'label' into one common base.yaml
that all the other yaml's can inherit from. This removes both
duplication and inconsistent definition.
The device specific yamls just need to say if a property is 'required'
or not.
NOTE: due to some generation conflicts we did not covert
'soc-nv-flash.yaml' to use base.yaml.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The legacy PCI support in the DesignWare I2C driver is replaced with
the new PCIe support. The Intel Quark X1000 SoC and the galileo board
configurations are updated accordingly.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Expose MEC1501 5 I2C/SMB controllers
Add Microchip specific I2C device tree properties
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
This adds a SERCOM I2C driver for SAM0 series chips.
Tested with a SAMD21 chip on a SSD1306 display and a MLX90393
sensor. Only compile tested for SAMD20 and SAMR21.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
Add driver and device tree binding for the Low Power Inter-Integrated
Circuit (LPI2C) controllers found in the RV32M1 RI5CY SoC.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
After commit 'scripts/dts: Never ignore properties in
generate_node_defines()', pointless entries for 'interrupt-names'
properties show up in generated_dts_board.conf and
generated_dts_board_fixups.h, because many bindings specify
'generate: define' for 'interrupt-names'.
If 'generation: define' is taken as "generate #define's for this
particular property", then only the 'interrupts' property ought to have
'generation: define'. Having it on both 'interrupts' and
'interrupt-names' makes you wonder what it would mean to only have it on
one of them.
Things get a bit confusing since 'interrupt-names' is still used when
determining the macro names generated for 'interrupts', but it's
probably best to have 'generation: define' work in a consistent way
still (and never be a no-op).
Remove 'generation: define' from all 'interrupt-names' bindings.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Driver for the I2C peripheral in the SiFive Blocks RTL
Repository (https://github.com/sifive/sifive-blocks).
Signed-off-by: Nathaniel Graff <nathaniel.graff@sifive.com>
Use the new DT_<COMPAT>_<INSTANCE>_<PROP> defines to instantiate
devices. This commit adds also ability to define individual pin
locations on SoC series that support the feature. Definitions of GPIO
pins assigned to a given location have been moved from soc_pinmap.h file
to board DTS file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
The Silicon Labs EFR32MG12P Mighty Gecko MCU includes:
* Cortex-M4F core at 40MHz
* up to 1024KB of flash and 256KB of RAM
* integrated Sub-GHz and/or 2.4GHz radio
* multiple low power peripherals
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
Signed-off-by: Endre Karlson <endre.karslon@gmail.com>
The 'id' field was never used and tended to just have the compat of the
node. Lets remove it and removed some code in extract_dts_includes.py
related to it. Added a warning if 'id' is set in a yaml so we can
remove it going forward.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add 'generation: define' directive to 'compatible' property.
When existing for a type of device, move compatible property
description in device base structure (eg: i2c.yaml)
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
