Converts the fxas21002 sensor driver to the new gpio api. Updates device
trees for all boards with this sensor to active low gpio interrupts by
default.
Tested on the hexiwear_k64 board.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
All sensors were using legacy log module registeration method
where LOG_LEVEL was defined before registeration. This method
was error prone as it requires preserving includes order.
Replaced with LOG_MODULE_REGISTER(foo, level).
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Use the named representation for no-wait to future-proof against a
change to the representation of timeout values.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
move misc/util.h to sys/util.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move misc/__assert.h to sys/__assert.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move sensor.h to drivers/sensor.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move i2c.h to drivers/i2c.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move gpio.h to drivers/gpio.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Change code from using now deprecated DT_<COMPAT>_<INSTANCE>_<PROP>
defines to using DT_INST_<INSTANCE>_<COMPAT>_<PROP>.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Every board that uses dts-enabled gpio drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_GPIO_DEVICE and
HAS_DTS_GPIO.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Every board that uses dts-enabled i2c drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_I2C_DEVICE and
HAS_DTS_I2C.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
A race condition was identified during the initialization of the
driver when the trigger function is enabled. This exposed two issues:
1 - The fxas21002_handle_int is trying to acquire the semaphore before
it gets initialized. To solve this we need to initialize the
semaphore before calling the fxas21002_trigger_init function.
2 - During the fxas21002_trigger initialization the i2c bus is used
(from fxas21002_handle_int function) at the same time as the
fxas21002_set_power is being called. To fix this we need to
initialize the semaphore with 0 and just release it after calling
the fxas21002_set_power function in the fxas21002_int
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Normally a syscall would check the current privilege level and then
decide to go to _impl_<syscall> directly or go through a
_handler_<syscall>.
__ZEPHYR_SUPERVISOR__ is a compiler optimization flag which will
make all the system calls from the driver files directly link
to the _impl_<syscall>. Thereby reducing the overhead of checking the
privileges.
In the previous implementation all the source files would be compiled
by zephyr_source() rule. This means that zephyr_* is a catchall CMake
library for source files that can be built purely with the include
paths, defines, and other compiler flags that all zephyr source
files uses. This states that adding one extra compiler flag for only
one complete directory would fail.
This limitation can be overcome by using zephyr_libray* APIs. This
creates a library for the required directories and it also supports
directory level properties.
Hence we use zephyr_library* to create a new library with
macro _ZEPHYR_SUPERVISOR_ for the optimization.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Adds dts bindings for the fxas21002 interrupt pins to all boards that
have this sensor.
The fxas21002 driver is currently only aware of one sensor interrupt
pin, therefore the routing of INT1 or INT2 to the driver is handled in
each board's dts.fixup.
The fxas21002 sample application has been broken since the refactoring
of the mcux gpio driver to dts in commit
4e8f29f319. The sample is now fixed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts yaml bindings for the fxas21002 sensor to allow the sensor
driver name, i2c driver name, and i2c address to be extracted from dts
instead of kconfig.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
- place all sensor Kconfig options in submenu
- separate device drivers and common options with a comment line
- align help text
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Change the common "init with 0" + "give" idiom to "init with 1". This
won't change the behavior or performance, but should decrease the size
ever so slightly.
This change has been performed mechanically with the following
Coccinelle script:
@@
expression SEM;
expression LIMIT;
expression TIMEOUT;
@@
- k_sem_init(SEM, 0, LIMIT);
- k_sem_give(SEM);
+ k_sem_init(SEM, 1, LIMIT);
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Update the MCUX I2C driver and related platforms to get their I2C
information from the device tree. We also updated a few of the sensor
drivers found on the FRDM & Hexiwear boards to get their I2C bus name
from the device tree instead of directly from Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Jira: ZEP-2051
Change-Id: I08f51e2bfd475f6245771c1bd2df7ffc744c48c4
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This reverts commit e60af3be66.
We revert this as we intent to move away from {u}int{8,16,32,64}_t types
to our own internal types for sized variables so we shouldn't need the
PRI macros anymore.
Change-Id: I4a57eb2c23cb1b137112224f604602d40c7cce4f
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To allow for various libc implementations (like newlib) in which the way
various {u}int{8,16,32}_t types are defined vary between both libc
implementations and across architectures we need to utilize the PRI
defines.
Change-Id: I69e60e3823028389b314adaf6e279fd47fde1182
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adds sensor driver support for the NXP FXAS21002 3-axis gyroscope.
Includes statically configurable range and output data rate, as well as
the sensor data ready trigger.
Datasheet:
http://www.nxp.com/assets/documents/data/en/data-sheets/FXAS21002.pdf
Jira: ZEP-1392
Change-Id: I84587c4d5e76863245e9d045c6abb10b21b2615a
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
