In case of dualcore, STM32H7, STM32W and STM32MP1,
protect concurrent register write access with HSEM.
Done for following drivers:
clock_control, counter, flash, gpio, interrupt_controller
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
This commit removes API functions and macros which were deprecated in
2.2 release. GPIO drivers are updated accordingly.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Several reviewers agreed that DT_HAS_NODE_STATUS_OKAY(...) was an
undesirable API for the following reasons:
- it's inconsistent with the rest of the DT_NODE_HAS_FOO names
- DT_NODE_HAS_FOO_BAR_BAZ(node) was agreed upon as a shorthand
for macros which are equivalent to
DT_NODE_HAS_FOO(node) && DT_NODE_HAS_BAR(node) &&
- DT_NODE_HAS_BAZ(node), and DT_HAS_NODE_STATUS_OKAY is an odd duck
- DT_NODE_HAS_STATUS(..., okay) was viewed as more readable anyway
- it is seen as a somewhat aesthetically challenged name
Replace all users with DT_NODE_HAS_STATUS(..., okay), which is
semantically equivalent.
This is mostly done with sed, but a few remaining cases were done by
hand, along with whitespace, docs, and comment changes. These special
cases include the Nordic SOC static assert files.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Rename DT_HAS_NODE to DT_HAS_NODE_STATUS_OKAY so the semantics are
clear. As going forward DT_HAS_NODE will report if a NODE exists
regardless of its status.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use device node declaration instead.
Clean up GPIO_STM32_PORT* Kconfig symbols.
On some boards some gpio ports where disabled using Kconfig symbols.
Disable them now via device tree nodes in boards dts files.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use gpio_pin_t uniformly when passing pin indexes to the driver. Use
gpio_flags_t uniformly when passing flags to the driver. Change name
of pin configuration function in API function table to be consistent
with other API functions.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The only remaining port operations have dedicated API function table
entries. Remove the defines for access op (mode), and remove support
for access op from all implementations.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The last external reference to these was removed when the pin
write/read functions were deprecated. Remove the syscall support, API
function table entries, and implementation from all drivers.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
These have been replaced by the appropriate call to
gpio_pin_interrupt_configure(). While the disable function could be
implemented using the new functionality, the enable function cannot
because the interrupt mode is not available. Consequently we cannot
replace these with equivalent functionality using the legacy API.
Clean up the internal implementation by removing the inaccessible
port-based enable/disable feature, leaving the pin-based capability in
place.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure. This driver uses fixups to define a common name
based on the SOC series; until aliases for the new properties are
added the code assumes all pins are supported.
Since pin ordinal validation is now done directly in gpio API,
remove checks inside the driver itself.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
stm32_exti_enable was returning errors on line > 32 or line pointing
to non implemented line. Both conditions are hard-coded, hence there
is no use to detect them dynamically in the code.
Check them with assert. As a consequence, function could now be void.
Additionally, enable exti irq line only if both checks are passed.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Since it is now possible to disable/re-enable interrupts and
also to reconfigure an already configured interrupt, it is
now required to clear non requested triggers.
While it is not strictly requested, triggers are also cleared
when interrupt is disabled (assuming trigger should be configured
when interrupt is enabled).
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
fixup exti
Perform few clean up in stm32 gpio driver:
*Clean up uint32_t occurrences left over.
*Move function gpio_stm32_flags_to_conf from const to static
and remove useless parameter check
*Rework error handling in functoin gpio_stm32_config
*Remove gpio_stm32_int_enabled_port function and have direct call
to gpio_stm32_get_exti_source
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
sam0 and stm32 specific interrupt controller headers are meant to be
public, and as such should be found in
include/drivers/interrupt_controller and not in
drivers/interrupt_controllers.
Fixing documentation issues as well.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Pattern being <domain>_<model>.<c/h>.
Here interrupt_controller as a domain would be far too long so
shortening it to "intc", as DTS does actually.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Up to now interrupts could be only configured once, with no way to
disable them in runtime.
Allow interrupts to be disabled in runtime and then properly reenabled
on user request. This allows to ignore interrupts when software is not
expecting them.
The improvement over previously reverted patch [1] is that we disable
interrupts only when we configure port for which interrupt line was
previously selected. This for example prevents to disable interrupts
line 2 in case PA2 was previously configured as interrupt source, but we
are currently configuring PB2 as output.
[1] 0951ce2d34 ("gpio: stm32: support disabling and reenabling
interrupts on pin")
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
This patch doesn't change functionality, but is only related to improved
readability and reusability.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
With dual core handling introduction, we now need to take care to
always release lock before exiting function.
Rework gpio_stm32_config to take this into account.
Additionally, since ENOSYS usage is resevred to system calls
handling, replace with EIO.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This reverts commit 0951ce2d34.
This change introduces regression on GPIO interrupts handling
when several GPIOs are configured.
Fixes#19177
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Up to now interrupts could be only configured once, with no way to
disable them in runtime.
Allow interrupts to be disabled in runtime and then properly reenabled
on user request. This allows to ignore interrupts when software is not
expecting them.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Some smaller stm32l0x MCUs, such as stm32l011x, do not have GPIOH
port. Fix build for those by checking LL_SYSCFG_EXTI_PORTH macro.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Add the serial wire JTAG configuration of the stm32f1x family.
Before gpio is initialized, you can choose to turn off the debug pin to
make the used pins available.
Signed-off-by: Findlay Feng <i@fengch.me>
HSEM_CR_COREID_CURRENT was used as process number parameter in
LL_HSEM_ReleaseLock function. While this is working, this
define should not be used in this context.
Also, process number parameter is actually proposed in case of HSEM
use in inter-process context but is not required for inter-core
resource lock. Replace HSEM_CR_COREID_CURRENT with 0.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Protect gpio_configure function in dual core context.
This operation is not needed for other fuctions of the api:
* init
* read
* write
Protecting gpio_configure also protects access to
interrupt_controller IP.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
move misc/util.h to sys/util.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move pinmux.h to drivers/pinmux.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move gpio.h to drivers/gpio.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The compiler and linker was generating errors after
disabling `CONFIG_EXTI_STM32` due to inconsistency
in `interrupt_controller/CMakeLists.txt`
and not considering this option in gpio implementation.
Signed-off-by: Maciej Zagrabski <maciej.zagrabski@grinn-global.com>
For STM32L47x/48x series devices, register ASCR should be configured to
connect analog switch of gpio lines to the ADC.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
Rename reserved function names in drivers/ subdirectory. Update
function macros concatenatenating function names with '##'. As
there is a conflict between the existing gpio_sch_manage_callback()
and _gpio_sch_manage_callback() names, leave the latter unmodified.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
Following configuration options are not supported by STM32
gpio driver:
-GPIO_INT_LEVEL
-GPIO_POL_INV
Return an error when one of these is requested.
Fixes#12766
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
It needs to verify if the callback was not already installed, and if so:
if is was in controller's list.
It should return an error in case the node is not found though it was
requested to be removed.
If already inserted, it will be silently removed but added again, to
avoid circular list as stated in the bug.
Fixes#11394
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Complete code factorization in stm32 exti drivers.
Add return value in case line is not implemented.
Except returned error code, refactor has been done iso-feature
compared to previous code. Hence error is reported only when
support was not available on previous series.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Behavior of function gpio_stm32_configure has been modified
during driver factorization. Various gpio settings (speed, mode, ..)
are applied conditionally while they used to be applied in sequence,
unconditionally before this change. As a consequence some
combinations of configurations are no more applied (like speed for
alternate mode). This of course has impact in some use cases.
Rework functions in order to apply settings unconditionally. Take
advantage of the change to reduce code size.
This change impacts all SoCs except F1 series.
Fixes#12544
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
