The version of OpenOCD provided by Zephyr SDK is too old and does not
contain support for EFR32FG1P chip. This patch assumes that user
compiles and installs the newest version of OpenOCD.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This config is only valid for kinetis boards. Fixes the Kconfig warning:
warning: the choice symbol OSC_EXTERNAL (defined at
arch/arm/soc/nxp_kinetis/Kconfig:53) was selected (set =y), but no
symbol ended up as the choice selection.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The LPCXpresso54114 command line example was using a wrong board
name which has been renamed after adding the support for the
Cortex-M0+ core.
Fixes#9649
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
This adds to the adc_api test board-specific configurations
for the following boards:
- nrf51_pca10028
- nrf52_pca10040
- nrf52840_pca10056
"adc" is indicated as supported in the yaml files for these boards
so that they are included in sanitycheck.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
ADC nodes are enabled in DTS for the following nRF development kits:
- nrf51_pca10028
- nrf52_pca10040
- nrf52_pca20020
- nrf52810_pca10040
- nrf52840_pca10056
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Use Kconfig specific object "named choices".
Aim is to allow to define config choices selection in Kconfig.*
files instead of _defconfig and hence allow to keep flags
activation conditional.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Rename GPIO_INT_CONF to GPIO_FLAGS in order to be able to use
the definition generated by the devicetree, eliminating the need
for definition in the board.h file
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
set DISK_FLASH_MAX_RW_SIZE to 256, as maximum bytes that can be
programed to SPI FLASH by Page Program Command is 256.
Fixes#8506
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
Now that the corresponding flash definitions have been added to the DTS,
it's possible to enable the nvs sample in the NUCLEO-L432KC board.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This patch adds DT description of generic storage flash partition using
the last 16kB of flash when CONFIG_FS_FLASH_STORAGE_PARTITION is
defined. This can be used for FCB or NVS filesystems.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Use the correct pyOCD target type for the NRF52840.
This fixes b92436a13f.
Tested with: Atmel ICE Debugger
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Removes the platform whitelist, leaving just the depends_on/supported
pattern to select which platforms the sample can run on.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add support for using non-jlink programmers through pyOCD.
Tested with: Atmel ICE Debugger
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add support for using non-jlink programmers through pyOCD.
Tested with: Atmel ICE Debugger
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
This patch is to add support for the WaRP7 board which has an i.MX7
Solo SoC.
The Zephyr is running on the Cortex M4 core and the following features
were validated on this board:
* GPIO: User Switch detection and sensors interrupt
* UART: Zephyr console
* I2C: Communication with fxos8700 and fxas21002 sensors
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
Move to more generic tracing hooks that can be implemented in different
ways and do not interfere with the kernel.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Fix in command line parsing common functions, to prevent
a possible segfault when handling string type arguments
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Added an entry in drivers/Kconfig for audio
Added an entry in drivers/audio/Kconfig for audio codec
Added an Kconfig file in drivers/audio/ for TLV320DAC
Enabled audio coded in Intel S1000 CRB defconfig
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
PR #8729 removed the old GPIO_NRF5 driver in favor of an
nrfx-based one. The reel_board still references the old one,
causing CI failures.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
As reported in issue #9494, BT samples are using the off-chip
UART-based BT controller on 52810. But the on-chip BT controller is
supported on 52810, so this is the reasonable default when BT is
enabled.
This patch enables BT_CTLR by default when BT is enabled.
This resolves#9494.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
I removed GPIO configuration from board files and enabled them
as default in driver Kconfig file. All boards had GPIO ports
enabled that is why I decided to enable it by default.
Power management example was changed to use new driver.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
FE310 is the name of one SoC out of a range of products in the SiFive
Freedom line. The FE310 SoC port in Zephyr is compatible with all of
these products, so rename the SoC to SiFive Freedom
Signed-off-by: Nathaniel Graff <nathaniel.graff@sifive.com>
This patch adds support for Ethernet in the STM32F2 family of
microcontrollers and enables it for the the Nucleo-F207ZG.
Signed-off-by: Daniel Egger <daniel@eggers-club.de>
A design flaw of 'gsource' is that there's no way to require at least
one file to match the glob pattern. This could lead to silent errors.
Switch to a new design, where a plain 'source' is globbing and requires
at least one file to match. A separate 'osource' (optional source)
statement is available for cases where it's okay for a pattern (or plain
filename) to not match any files.
'orsource' combines 'osource' and 'rsource' (relative source).
This commit search-replaces 'gsource' with 'source', but backwards
compatibility with 'gsource' is still maintained by making it an alias
for 'osource' (and by making 'grsource' an alias for 'orsource').
The three Kconfig files arch/{nios2,posix,xtensa}/Kconfig source
arch/{nios2,posix,xtensa}/soc/*/Kconfig, which doesn't match any files.
Use 'osource' for those. The soc/*/Kconfig files seem to be for
additional SoC-specific symbols, only none exist yet on those ARCHes.
Also use 'osource' for the source of $ENV_VAR_BOARD_DIR/Kconfig in
boards/Kconfig, which doesn't exist for all boards.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The old GCC ARM Embedded website on launchpad
(https://launchpad.net/gcc-arm-embedded) has been superseeded by the new
GNU Arm Embedded one
(https://developer.arm.com/open-source/gnu-toolchain/gnu-rm).
This also means a change of name from "GCC" to "GNU". Reflect this in
the enviroment variables so that the proper term is used henceforth.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
A bug in the jlink application made it impossible to use OpenSDA
firmware with the mimxrt1052 device name, so we used the generic
Cortex-M7 device name as a workaround. This bug was fixed in jlink
V6.32h (2018-07-05), so now we can use the more specific device name.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
These settings enable use of the WNC-M14A2A LTE-M modem as the default
network interface for the nRF52840-DK board (nrf52840_pca10056).
They include the following settings when MODEM_WNCM14A2A is selected:
- UARTE1 pin setup
- DTS / DTS fixup additions for WNC-M14A2A
- Kconfig settings for modem driver
Signed-off-by: Michael Scott <mike@foundries.io>
These settings enable use of the WNC-M14A2A LTE-M modem as the default
network interface instead of ethernet.
They include the following settings when MODEM_WNCM14A2A is selected:
- UART 2 setup
- Avoid ETH_0 setup due to pin conflicts
- DTS addition for WNC-M14A2A
- Kconfig settings for modem driver
Signed-off-by: Michael Scott <mike@foundries.io>
