Sync peripheral mapping documentation with the Nucleo F429ZI board doc
and add missing information about Ethernet and the button.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
To ensure we can always go back in time, let's explicitly list the
NRF52 HW models version which should be used with each version of
the nrf52_bsim board
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Added a new simulated board, which models the NRF52832 SOC.
Its main use is for workstation testing and simulation of
the BLE stack and any application which relies mostly on it.
It uses BabbleSim (http://Babblesim.github.io) for the radio
simulation.
And the NRF52 HW models hosted in that same GitHub organization:
https://github.com/BabbleSim/ext_NRF52_hw_models
For speed it uses the POSIX arch to (not) emulate the CPU.
It uses Vanilla Zephyr, with a couple of configuration differences:
* It uses (like other POSIX arch boards) the system libC
* It does not use the nrfx hosted by Zehpyr in ext/, but the one
provided by the HW models.
Otherwise it relies in the same drivers as the real NRF52 boards.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
This commit is taking care of following stuff:
1. pinmux: STM32F4 micro is using I2S5_CK and I2S_SD to interface with
on-board microphone.
2. default configuration:
- enable I2S5 and configure PLLI2S properly to generate
I2SxCLK = 128MHz.
- enable DMA
Note:
As stated in issue #9028 we needed to take care of a known SPI/I2S bug
implementing the following two actions:
A. APB2 clock has been slowed down to 42MHz.
B. The SPI/I2S clock gpio speed has been set to very_high_speed.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Previously, wifi-enabled samples were not built by sanitycheck for the
cc3220sf_launchxl.
This patch gets the sockets echo sample to build.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The USART fixup in the board dir really are SoC level fixup's. So move
them there and remove the board fixup file since there isn't anything in
it now.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Contrary to what was written in its Kconfig, hal/altera depends not
on Newlib, but on a baseline POSIXish define like O_NONBLOCK. Minimal
libc now provides them, so there're no issues with building Altera
for either minimal on newlib libc.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The EFM32 Happy Gecko USB-enabled kit contains sensors and
peripherals demonstrating some of the EFM32HG MCU capabilities.
This patch add basic support for this board.
Signed-off-by: Marcio Montenegro <mtuxpe@gmail.com>
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Convert over arc based boards to use device tree instead of board.h to
describe buttons & LEDs. There are a few boards that the button gpio
flags need validation.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This will be usefull to tell when Ethernet device has its attributes
filled in by DTS rather than by Kconfig.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Convert over SiLabs based boards to use device tree instead of board.h
to describe buttons & LEDs. There are a few boards that the button
gpio flags need validation.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert over x86 based boards to use device tree instead of board.h to
describe buttons & LEDs. There are a few boards that the button gpio
flags need validation.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As per default board configuration guidelines, this commit updates
96Boards Nitrogen board.
Following changes are done:
- Enable I2C0 and SPI0 in board dts
- Add exposed peripherals in board Kconfig
- Update board yaml
- Remove config option to select board
- Update documentation for UART, I2C and SPI
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
As per default board configuration guidelines, this commit updates
96Boards Carbon board.
Following changes are done:
- Enable exposed I2C2 in dts
- Only enable basic peripherals in board defconfig
- Add exposed peripherals in board Kconfig
- Update documentation for SPI
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Convert over NRF based boards to use device tree instead of board.h to
describe buttons & LEDs. There are a few boards that the button gpio
flags need validation.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The commit de78ecd "arm: beetle: Use device tree for IRQs" introduces
a regression related to UART1 IRQ.
On arm beetle the UART1 has IRQ number 2.
This patch restores the functionality modifying the arm beetle device
tree file.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
The Zephyr configuration system uses many different files in many
different formats. It makes it a lot easier for users to understand
what these files do if when we use the correct file extensions.
To this end we rename the dts.fixup files to the correct file
extension '.h'.
This is a breaking change for out-of-tree fixup files. Such files will
be detected and given an appropriate error message.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
The dts.fixup for the hifive1 board was not board specific but related
to the SoC. Move the dts.fixup into the SoC dir so any other boards
using this same SoC will take advantage of it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move to getting the clock frequency of the uart from the device tree
instead of a define in the board file. Cleaned up hifive1 board code to
reflect this change in addition to the driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Some of the headers referenced in the pinmux.c file don't exist. Match
the includes that the lpcxpresso54114_m4 pinmux.c file uses.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add the needed bits to get device tree support for the GPIO controller
on the Zedboard-Pulpino. This will allow us to move LED & button info
into the board.dts.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add simple device tree support for the Pulpino SoC and Zedboard-Pulpino
board port. This gets the UART info from device tree instead of soc.h
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add i2c/spi/gpio to the supported list to enable the CI to correctly
run the 96b_argonkey board sample.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This patch is equivalent to 7b0ce85242,
but applied to buttons. As stated in the previous commit message:
This change aims at fixing 'unit_address_vs_reg' warning in arm based
boards. This warning pops up when a node name is made up with an
address (node_name@xx) but does not contain a reg property. This case
was encountered for led nodes for instance, where a reg property has
no meaning. Fix this by changing node_name@xx to node_name_xx which
removes the guilty '@XX' syntax but preserves node_name uniqueness.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
The device name was missing for the lsm6dsl sensor in the 96b_argonkey
dts fixup, causing build warnings in tests/drivers/build_all.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
added sam4s16b, sam4s8c, sam4s8b, sam4s4c, sam4s4b,
sam4s4a, sam4s2c, sam4s2b and sam4s2a.
Used the same order as in the data sheet and code structure
equal to same70. Updated the sam4s_xplained board to match
the altered .dtsi location of the specific SoC.
Signed-off-by: Vincent van der Locht <vincent@vlotech.nl>
Remove the links to the now non-existant legacy shell documentation
and clarify a bit paragraphs (as the legacy shell is not default
anymore)
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
