Enable by default the following hardware instances in Kconfig:
- ADC_0
- I2C_0
- SPI_1 (SPI_0 for nRF52810)
for all nRF development kit boards having the corresponding DT nodes
enabled. This way there is no need to enable these instances in
particular applications, like samples for sensors or tests for drivers.
I2C_0 and SPI_0 cannot be used simultaneously in most of nRF SoCs,
nRF52810 is the only exception so far (and in this SoC SPI_1 is not
present, hence SPI_0 is enabled for it).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The options selecting nRF drivers are now enabled by default when
an nRF SoC is selected as the build target.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Fixes board PHY initialization.
ENET_RST and ENET_INT pins are also used as USER_LED/JTAG_TDI and
INT1_COMBO/JTAG_TDO. Initialization needs to set these pins to power and
interrupt for the PHY Transciver. PHY reset works without busy waiting.
Moved pin initialization back to PRE_KERNEL_1 to fix UART bug and busy
wait not required.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Added support for SPI 1 available from the arduino connector (plus an
extra gpio). Tested against samples/sensor/bme280.
Added warnings in documentation, pinmux and dts highlighting a potential
conflict if using SPI_1 and on-board ethernet at the same time.
Signed-off-by: AJ Palmer <ajpcode@hotmail.com>
Added board definitions for nucleo_f756zg. Features include gpio,
pinmux, uart (ST Zio, ST-Link and Arduino Uno v3 interfaces).
Added basic documentation and some soc definitions for the
stm32 f756XX soc.
Signed-off-by: AJ Palmer <ajpcode@hotmail.com>
Updated .dts and pinmux.c to highlight pin conflict on PA7 if ETH and
SPI_1 are selected together without modification.
Signed-off-by: AJ Palmer <ajpcode@hotmail.com>
STM32 uart Kconfig instance flags were not following
same naming scheme than other drivers (i2c, spi, ..)
Update driver to use UART_X instead of UART_STM32_PORT_X
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This patch cleans up the code in the recently added dts_fixup.h,
restoring the original alignment of the file.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
The dts.fixup for mps2_an385 contains a wrong setting for the IRQ fixup
for the Dual Timer IRQ.
This patch fixes the symbol included in the generated header.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
To enable the Hyperflash you have to physically modify the board and
this disables the QSPI. Since we plan on removing Kconfig from device
trees, its easier to treat the hyperflash as a separate board config
and thus it will get a dts to match.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Since Voltage Reference block is not supported, the ADC does not work
properly on FRDM-KW41Z. Set voltage reference to alternate source
in frdm_kw41z_defconfig.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
We had SEGGER support enabled by default previously, but the new
Kconfig option CONFIG_USE_SEGGER_RTT needs to be set as well now.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The lpcxpresso54114_m0 tends to be the secondary core so doesn't
typically have a UART setup for it. We had SEGGER support enabled by
default previously, but the new Kconfig option CONFIG_USE_SEGGER_RTT
needs to be set as well now.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add board support for 96Boards STM32 Sensor Mezzanine board. This board
is one of the 96Boards Mezzanine board which can work standalone or on
top of the 96Boards Consumer Edition boards.
Below are some of the key features of this board:
1. STM32F446VE MCU
2. 96Boards high/low-speed connectivity
3. Arduino™ Uno revision 3 and Grove connectivity
4. Integrated MEMS sensors:
1. LSM6DS3H
2. LIS3MDL
3. LPS22HB
4. MP34DT01-M
5. On-board ST-LINK/V2-1 debugger/programmer
More information about this board can be found in the 96Boards product
page: https://www.96boards.org/documentation/mezzanine/stm32/
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The 0.9.5 SDK has support for the Cypress PSoC6 family. Add ablilty to
flash with openocd. I've only tested flashing hello_world on the m0.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To enable the QSPI you have to physically modify the board and this
disables the hyperflash. Since we plan on removing Kconfig from device
trees, its easier to treat the QSPI flash as a seperate board config and
thus it will get a dts to match.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This driver introduces an emulated LCD display for the native POSIX
board. The emulated display driver makes use of SDL2 to render the
displays frame buffer into a dedicated desktop window.
Signed-off-by: Jan Van Winkel <jan.van_winkel@dxplore.eu>
Zephyr SDK 0.9.4 added OpenOCD support for SiLabs EFR32FG1P SoC. This
commit updates 'Flashing' paragraph of the board documentation to
reflect this change.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Fixes broken user guide and schematics links in nxp board documentation.
Updates remaining nxp.com links from http to https.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Connectors imaages for nucleo_f413zh were actually a reuse of
similar board nucleo_f412zg.
Add dedicated images for nucleo_f413zh.
Fixes#5198
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
'make flash' always erase the flash banks from sector 0, and flashing
the Zephyr.bin file to base address of flash even if there has a
bootloader placed on the first sector.
Users maybe want placed Zephyr to another location instead of sector
0 by adding 'zephyr,code-partition' in dts. But the openocd scripts
doesn't deal with that currently.
Fix this issue, flash zephyr.elf instead of zephyr.bin, elf file
contain load address and openocd scripts can deal with it.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Now that we can support the same compatible but different bus types,
update the LSM6DSL support to utilize the same compatible for either I2C
or SPI. We rename the i2c binding file to st,lsm6dsl-i2c.yaml just to
be a bit more clear.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Removed Console dependencies from shell uart backend.
Generated define: CONFIG_UART_SHELL_ON_DEV_NAME for each board.
Fixes#10191
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
In commit d8e3ea6bc2
the LF clock interrupt was enabled, which causes its interrupt
handler to be used. This interrupt handler interacts with the
NRF_POWER registers.
Therefore require using the newer HW models which include a stub
of this registers.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
CONFIG_TEXT_SECTION_OFFSET allows the entire image to be moved
in memory to allow space for some type of header. The mcubootloader
can boot only such images which reserve some space for the header.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
This patch enables the UART_INTERRUPT_DRIVEN by default for
colibri_imx7d_m4, udoo_neo_full_m4 and warp7_m4 boards.
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
Reel Board doesn't enable BT by default like many of the nRF52
boards do. So let's make enabling BT a bit easier, by selecting
the BT_CTLR config when BT is enabled. This allows a sample
overlay to merely set:
CONFIG_BT=y
And the end result should be close to correct.
Signed-off-by: Michael Scott <mike@foundries.io>
The nRF51822 and nRF52832 does not support 802.15.4, so remove this
statement from documentation.
Signed-off-by: Stig Bjørlykke <stig.bjorlykke@nordicsemi.no>
