Since there is no NFC antenna connector on the dongle and the pins
P0.09 and P0.10 that are dedicated to NFC functionality are in the
group of just a few ones available for external connections, it seems
more reasonable to configure these pins by default as regular GPIOs,
as users will most likely want to use them in this way.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
These definitions were left incorrect after a gpio-map change was
added to the PR introducing the boron support for the SARA-R4 modem.
Correct the gpio defintions here so that the boron build doesn't
break.
Fixes: https://github.com/zephyrproject-rtos/zephyr/issues/16289
Signed-off-by: Michael Scott <mike@foundries.io>
Enable pull-up on UART TX pin to reduce power consumption.
If the board is powered by battery the SoC consumes more
power than expected.
The consumption increases because TX pin is floating
(High-Impedance state of pin B from Dual-Supply Bus Transceiver).
Similar to commit b5b728495b
("boards: reel_board: enable pull-up on UART RX pin")
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
The Particle.io Boron is an nRF52840-based board with a connected
u-blox SARA-R4 modem. The main board was previously upstreamed
without modem support.
Now that we have a driver to support the SARA-R4 modem, let's enable
it for the Boron board.
Signed-off-by: Michael Scott <mike@foundries.io>
Let's change the specific WNC-M14A2A check into a more generic
MODEM check for enabling ethernet. Many of these pins are used
on the Arduino headers.
Signed-off-by: Michael Scott <mike@foundries.io>
This commit adds a DTS node for the ARM MPU peripheral in the
device tree of ARMv8-M SoCs (for the secure and the non-secure
DTS descriptions) and updates the fixup files. SoCs:
- nrf9160
- musca_a
- musca_b1
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
MHU (Message Handling Unit) enables software to raise interrupts to
the processor cores. It is enabled in SSE 200 subsystems.
This patch aims to implement inter processor communication.
Signed-off-by: Karl Zhang <karl.zhang@linaro.org>
Add support for the NXP TWR-KE18F development board. This board
feautures an NXP MKE18F16 MCU, a selection of user LEDs and
push-buttons, potentiometer, thermistor, CAN interface, and FlexIO
header.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The mikroe_mini_m4_for_stm32 board is developed by Mikroelektronika
not by STMicroelectronics.
Also use more appropriate "mini-m4-for-stm32" board name for
compatible dt property.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Enable the counter capability in the board and add a .conf file for the
nRF52810 running on the PCA10040 board.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The supported field is used by sanitycheck to select which tests will be
run on a particular board. The issue with the counter drivers, and in
particular on nRF ICs, is that the timer peripherals are disabled by
default and need to be enabled on a per-board basis inside a .conf file.
Since this board doesn't have a .conf file in
tests/drivers/counter/counter_basic_api/boards/ the test cannot be run
on this board.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This commit adds support for board: nrf52811_PCA10056.
The nRF52840 DK: PCA10056 is the recommend development kit, it emulates
the nRF52811, and can be used as a starting point for development
before moving over to a custom board.
Please note that this development kit does not support Bluetooth
Direction Finding. What is more it cannot be used with most of Arduino
shields because of PCA10056 PIN layout.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This commit adds J-Link runner for efr32_slwstk6061a board. To use it
it is necessary to install J-Link Software and Documentation Pack.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This commit enables internal SoC DC-DC converter on efr32_slwstk6061a
board.
RF components on efr32_slwstk6061a board are connected to the internal
SoC DC-DC converter. Upon startup the DC-DC converter is configured in
the bypass mode. Such configuration provides enough power for the SoC to
boot and perform basic operation. It is not enough however to operate
the radio subsystem. Without this patch enabling radio in Rx or Tx mode
causes voltage drop and triggers brown out detector reset.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Hook up SERCOM1 to I2C, it is connected to the EXT3 header and
the EDBG embedded debugging interface.
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
The ADC driver in this PR has been tested working on these nucleo
boards, so ADC support is added to the boards doc.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
Some configuration for the boards have to be added into test_adc.c file
so user can test driver with the test cases. Several nucleo boards are
added including F091RC/F103RB/F207ZG/F302R8/F401RE/F746ZG/L073RZ/L476RG.
And also ADC dts and pinmux configuration are added into boards own
pinmux.c and dts file.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
Let allow users to select the revision B of the chip on the SAM E70
Xplained Board. The same board exists with SoC revision A or B.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
At the moment there are two images for Nucleo-64 STM32 family board
connectors (img/nucleo_xxxxxx_connectors.png).
The images have the same canvas size (800x619) but different file
size in bytes and different color coding.
The first one (192K, 8-bit colormap) is used for
* nucleo_f070rb
* nucleo_f091rc
* nucleo_f103rb
* nucleo_l053r8
* nucleo_l073rz
The second one (464K, 8-bit/color RGBA) is used for
* nucleo_f030r8
* nucleo_f302r8
* nucleo_f334r8
Applying simultaneous black/white threshold to the images and
comparing them with imagemagick tools shows that the images
have no significant difference. Therefore we can use
nucleo_l073rz_connectors.png for nucleo_f030r8, nucleo_f302r8
and nucleo_f334r8.
Please see https://github.com/zephyrproject-rtos/zephyr/pull/15926
for details.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
The Holyiot YJ-16019 board is a small, coin cell driven board based on
the Nordic Semiconductors nRF52832. It provides one LED and one push
button.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
The approved trademark name is Wi-Fi so update references to WiFi and
other spellings to Wi-Fi in documentation and Kconfig help strings.
(Note that use of spelling variatios of "wifi" in module names, CONFIG
names, link names and such are untouched.)
https://www.wi-fi.org/
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
The stm32_min_dev board blue/black variant support USB device,
but the usb node removed by merge PR #15245, so add it back.
Signed-off-by: Harry Jiang <explora26@gmail.com>
The TI CC1352R LaunchPad (LAUNCHXL-CC1352R1) is a development kit that
features the CC1352R SoC.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
The TI CC26x2R LaunchPad (LAUNCHXL-CC26X2R1) is a development kit that
features the CC2652R SoC.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
Fix "arduino_i2c not found" issue, similar to #13708
Add arduino interfaces in dts to board nrf52_10040
Signed-off-by: Aaron Tsui <aaron.tsui@outlook.com>
