Add and mark PCIe highmem outbound memory as nGnRnE device memory
in Viper SoC MMU configuration.
Increase VA/PA bits to 36-bits to support the same.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Adds the chip select devicetree flags to the spi_cs_control instance.
ISM43362 chip select is ACTIVE_LOW.
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
This commit adds the PWM LED definition in the board device tree for
the on-board LED connected to the pin PC18.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
CLOCK_STM32_PLL_XTPRE Kconfig symbols was made to differentiate
code between F1 soc variants with XTRE and others.
It appears that specific XTRE code handling is already in place in
LL_PLL_ConfigSystemClock_* functions that are called afterwards.
Since this piece of code is not required anymore, let's remove
the symbol.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit adds the PWM LED definition in the board device tree for
the on-board LED connected to the pin PB30.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The preceeding patches causes bossac to automatically pull the flash
address from DeviceTree, so drop the explicit flag.
Signed-off-by: Michael Hope <mlhx@google.com>
This commit makes it possible to use stm32flash for flashing (with west)
the STM32F030 Demo Board. OpenOCD is still the default, so in order to
use stm32flash, one must invoke ‘west flash’ with ‘-r stm32flash’.
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Enable TCC0, define the PWM LED, document, and add to the peripheral
list.
Tested using samples/basic/fade_led/
Signed-off-by: Michael Hope <mlhx@google.com>
The common code now auto selects drivers. Update the Trinket to match
the Arduino Zero including trimming the defconfig and listing the
supported peripherals.
Signed-off-by: Michael Hope <mlhx@google.com>
The Seeeduino XIAO is a tiny (20 mm x 17.5 mm) ARM development
board with onboard LEDs, USB port, and range of I/O broken out
onto 14 pins.
Signed-off-by: Michael Hope <mlhx@google.com>
This enables PWM and connects it to the main LED. Tested by running
samples/basic/blinky_pwm and /fade_led.
Signed-off-by: Michael Hope <mlhx@google.com>
Fixes#26413.
The devicetree for disco_l475_iot1 declares the flash partitions
"storage" and "image-scratch" with overlapping address spaces.
As a result, when one of these partitions is used it can corrupt the
contents of the other one. This is the case when mcuboot performs an
image swap using the scratch partition.
To fix the bug, the size of the scratch partition is reduced.
Signed-off-by: Hans Wilmers <hans@wilmers.no>
In this board DT the "storage" and "image-scratch" are declared
with overlapping address spaces.
As a result, when one of these partitions is used it can corrupt the
contents of the other one. This is the case when mcuboot performs an
image swap using the scratch partition.
To fix the bug, the size of the scratch partition is reduced.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Fixes the frdm_k64f and twr_ke18f boards to enable the kinetis
temperature sensor only if the sensor and adc drivers are both enabled.
This fixes a logging error seen at runtime in
samples/bluetooth/peripheral_hr.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Plus corresponding configuration file for the spi_loopback test that
will be activated for that board by this added capability.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
No need to specify a default configuration for
ENTROPY_NRF_FORCE_ALT Kconfig symbol in the
qemu_cortex_m0 board definition.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
We rework the timer driver for Cortex-M0 QEMU Board.
The driver is adapted to follow the (recent) nRF RTC
driver logic, and adaptations are made simply because
the driver is based on the TIMER peripheral instead of
the RTC.
A couple of tweaks are added due to QEMU issues with the
simulation of the TIMER peripheral.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Instead of endlessly repeating the same command line args,
centralize this and tune the shift value on a per-board
basis.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This patch enables the Independent watchdog (iwdg)
so that the testcase tests/drivers/watchdog/wdt_basic_api
can run on this stm32f3_disco board
Signed-off-by: Francois Ramu <francois.ramu@st.com>
All pinmux supporting CAN, SPI and I2C of F7 series are added.
Since the F7 series supports up to two CANs,
the pin names of CANs have been changed.
Several minor pinmux errors have also been fixed.
Sorted by Alternate function.
Signed-off-by: Kwon Tae-young <tykwon@m2i.co.kr>
PA selection mainly depends on board design. So it looks like
device-tree is a better mechanism than Kconfig in this case. Use string
property with two possible values: "rfo" and "pa-boost".
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Changes to the PLL configuration were required
for proper device enumeration. Now there is a 48MHz USB clock
(was 25MHz), and a 96MHz system clock (was 100 MHz).
Addresses #25293
Signed-off-by: Brian Bradley <brian.bradley.p@gmail.com>
Now that the SAM0 SOC selects the appropriate SAM0 driver for a class,
reduce the drivers that are compiled in by default on the Arduino
Zero. This reduces the size of `blink` from ~14 KiB to ~10 KiB.
Also add the supported features to arduino_zero.yaml to get more
coverage in the sanity tests.
Signed-off-by: Michael Hope <mlhx@google.com>
The DTS for nRF53 and nRF91 boards has been modified to cut the size
of boot partition from 64KiB to 48KiB, making it the same size as for
nRF52.
Resolves#25664
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Only boards with at least 64K Flash will activate MPU because:
MPU + UERSPACE + All switches implicity activated
(CONFIG_MPU_STACK_GUARD, CONFIG_ARM_STACK_PROTECTION ...)
will consume about 40K Flash
(value computed on nucleo_f767_zi on tests/arch/arm/arm_ramfunc/).
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
Add support for the polarity flag in the STM32 PWM driver.
STM32 boards using PWM have been updated accordingly.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Add devicetree nodes for the Arduino GPIO and MikroElektronika
mikroBUS headers present on the NXP LPCXpresso55S16 development board.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Enable GPIO as a workaround to enable some SPI slaves are not correctly
controlled using the Flexcomm SPI device.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
This patch introduces the new b_l4s5i_iot01a discovery kit
from STMicroelectronics.
This is a IOT node based on the stm32l4s5vi
including MEMS, Bluetooth BLE, WiFi and NFC modules
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Replace usage of deprecated GPIO_INT_ACTIVE_LOW, GPIO_INT_ACTIVE_HIGH,
GPIO_PUD_PULL_UP flags with a new equivalent in a few boards that were
added after 2.2 release.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Added / Tested support for RNG on the STM32F767ZI nucleo board.
Updated the SoC defconfig to auto-enable the driver when
ENTROPY_GENERATOR is enabled, and updated the board README.
Signed-off-by: Bilal Wasim <bilalwasim676@gmail.com>
tested on mimxrt1060_evt
MEMORY_NOCACHE is needed
test on frdmk64f
special test slot need configure with
CONFIG_DMA_TEST_SLOT_START
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
Add support for Bluetooth Controller GPIO Debug Pins for
nRF5340 PDK board. GPIO Pin toggling can be captured on the
P3 pinhead of the PDK.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The `netif` capability is needed for certain samples to be built by the
CI for a target platform. As it was missing for nrf52840dk_nrf52840,
echo samples with OpenThread support were not being built and thus not
tested by the CI.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The STM32L072CZ MCU has a built-in USB device controller which is
supported by Zephyr's USB STM32 driver. The b_l072z_lrwan1 board has a
micro-USB connector that is wired to the MCU via two solder bridges
(SB15 and SB16) that need to be closed to connect the data lines.
Update the board documentation to describe the solder bridges and
enable the USB controller in the device tree.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
Provide devicetree configuration for UART2 on the mesh feather header.
The peripheral must be enabled in an overlay, optionally including a
provided overlay with the hardware flow control signals.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Default alternate function for the MEC15xx VCI pins makes them
HW-controlled.
Most common scenario is that pins are used as GPIOs, however
there are still some board designs where HW-controlled is desired.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
The ip_k66f board can run with clock frequency of 180 MHz. This requires
switching it to high speed mode (HSRUN).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This patch adds information regarding usage of serial console on
the ip_k66f board, as it only can use Segger's RTT console for
communication.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This change allows usage of larger RTT "UP" buffers from target to host.
It is necessary to allow correct execution of ping command:
net ping 192.168.0.1
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The ip_k66f board (embOS/IP switch) from Segger doesn't have the serial
console pins connected to J-Link OB. As a result one needs to use RTT
to get the serial console.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The documentation page in Zephyr states that the STM32L072CZ has 20KiB
of EEPROM. This is incorrect, the datasheet (and DTS) indicates that
it has 6KiB of EEPROM.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
The STM32L072CZ has an EEPROM for user configuration. Enable this for
the B-L072Z-LRWAN1 Discovery kit.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
This patch enables the rtc so that the testcase
tests/drivers/counter/counter_basic_api
can run on this nucleo_stm32f207 board
also when running sanity check
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The "gccarmemb" toolchain type has been renamed to "gnuarmemb" to
better reflect the official naming.
This commit replaces all references to the "gccarmemb" toolchain type
to "gnuarmemb".
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Removed flow control configuration from Kconfig and updated samples
to use device tree for that.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
The Adafruit ItsyBitsy M4 express is a small (36 mm x 18 mm) ARM
development board with an onboard RGB LED, USB port, 2 MiB of SPI
flash, and range of I/O broken out onto 23 GPIO pins.
Signed-off-by: Michael Hope <mlhx@google.com>
In order for the application to be flashed beginning at address 0,
which is desired when flashing with an external probe,
BOARD_HAS_NRF5_BOOTLOADER must be set to n.
Signed-off-by: Jacob Siverskog <jacob@teenage.engineering>
This follows the board porting guide. Only the the board
efm32hg_slstk3400a does not include a SoC containting an MPU.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
We only need a 'compatible' entry for the DK,
not the SoC and part-number. This commit fixes
this and aligns the nRF5340 PDK DTS with the
remainder of nRF-based boards.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Conditionalizes csi pinmuxes on CONFIG_VIDEO for all nxp boards
(kinetis, lpc, and imx families) to avoid possible conflicts between
peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes display pinmuxes on CONFIG_DISPLAY for all nxp boards
(kinetis, lpc, and imx families) to avoid possible conflicts between
peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes dac pinmuxes on CONFIG_DAC for all nxp boards (kinetis,
lpc, and imx families) to avoid possible conflicts between peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes can pinmuxes on CONFIG_CAN for all nxp boards (kinetis,
lpc, and imx families) to avoid possible conflicts between peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes ethernet pinmuxes on CONFIG_NET_L2_ETHERNET for all nxp
boards (kinetis, lpc, and imx families) to avoid possible conflicts
between peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes pwm pinmuxes on CONFIG_PWM for all nxp boards (kinetis,
lpc, and imx families) to avoid possible conflicts between peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes adc pinmuxes on CONFIG_ADC for all nxp boards (kinetis,
lpc, and imx families) to avoid possible conflicts between peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes i2c pinmuxes on CONFIG_I2C for all nxp boards (kinetis,
lpc, and imx families) to avoid possible conflicts between peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes spi pinmuxes on CONFIG_SPI for all nxp boards (kinetis,
lpc, and imx families) to avoid possible conflicts between peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes serial pinmuxes on CONFIG_SERIAL for all nxp boards
(kinetis, lpc, and imx families) to avoid possible conflicts between
peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Michael Hope
