I2C interrupts usage should be the preferred way. This commit
enables them by default in the STM32 I2C driver itself.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Same deal as in commit 677f1e6 ("config: Turn pointless/confusing
'menuconfig's into 'config's"), for a newly-introduced stuff.
Also clean up headers to be consistent with recent cleanups.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
During the first real test of my manual by another developer,
I found out that it would be better to update sequence of events.
Also found out misprints, and some actions was not so obvious.
Corrected manual to be more green developers friendly.
Signed-off-by: Maksim Masalski <maksim.masalski@intel.com>
Add the user button to the device tree of nucleo_l452re board.
This button is wire to the pin PC13 of STM32L452
Signed-off-by: Julien D'ascenzio <julien.dascenzio@paratronic.fr>
This commit adds initial support for the Silicon Labs EFM32
Giant Gecko GG11 StarterKit.
Features supported for now are NVIC, SysTick, GPIO, Flash,
Counter, I2C, UART and Ethernet. Support for Watchdog and
ADC will follow as soon as their respective PRs are merged.
Signed-off-by: Oane Kingma <o.kingma@interay.com>
nrf52811_pca10056 board should enable nRF 802.15.4 radio driver
automatically when 802.15.4 subsystem is enabled, as other Nordic
802.15.4-compliant boards do.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Replaced NFFS mentions by LittleFS in all <board>.dts comments
to storage partitions.
Replaced NFFS by LittleFS in a few boards documentation.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
...instead of kconfig.
This provides a bit more flexibility in defining driver
instances. Also, since the DTS defines 5 I2C controllers,
the driver code is extended to cover all 5 if the controllers
are enabled.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The I2C controllers on the MEC1501 SoC can be attached to
different I2C output line. For example, the I2C #0 controller
can be used with I2C7 physical lines out of SoC. The output
selection is done by the attribute "port_sel". This renames
the parent I2C nodes on the SoC side to refer to
the controller themselves instead of the output lines to
avoid confusion. The labels of these nodes are also renamed
to reflect the controllers.
On the board level, the DTS labels are overwritten to indicate
the actual output lines.
Aliases are also provided in both SoC and board levels to
provide shortcuts to the DTS nodes.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The SoC, driver, and board support for the CC2650 and CC2650 Sensortag
aren't currently supported and we are removing them as such. If anyone
is interesting in supporting this platform we can easily recovery it
from git.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
HAS_SEGGER_RTT is assigned by various Nordic boards, but assignments
have no effect on promptless symbols. This symbol is enabled through
being select'ed by SOC_SERIES_NRF52X.
Holyiot, nRF52833-PCA10100, nRF52840-PCA10056, and nRF52-PCA10040 only
assign HAS_SEGGER_RTT without assigning USE_SEGGER_RTT. They probably
meant to enable USE_SEGGER_RTT, so do that instead.
Also add a help text to HAS_SEGGER_RTT and a warning re. HAS_SEGGER_RTT
vs. USE_SEGGER_RTT to the documentation.
Flagged by https://github.com/zephyrproject-rtos/zephyr/pull/20742.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Error in that manual.
Header JP39 should have connected jumpers 1-2, 3-4.
In docs I wrote that is to make sure JP39 does not have any jumper.
Signed-off-by: Maksim Masalski <maksim.masalski@intel.com>
Added dts additions for stm32 nucleo f767zi board, also added
and modified soc addtions for thet board.
Updated dts reference file name.
Updated yaml to take out adc for now.
Signed-off-by: Roland Ma <rolandma@yahoo.com>
Flashing board nucleo_f207zg requires additional instructions
to be provided to openocd in order to enable flashing without holding
the reset button.
Update nucleo_f207zg openocd config to provide requested instructions.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
We need to include soc.h in nrf5340_cpunet_reset.c, to include
the nRF5340 device headers. Fixes a compilation error when we
build with CONFIG_ARM_MPU=n.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Add reference to wpanusb and wpan_serial examples. This links user with
some IEEE 802.15.4 applications.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Assignments have no effect on promptless symbols. Flagged by
https://github.com/zephyrproject-rtos/zephyr/pull/20742.
This symbol is (always) selected, in
soc/arm/ti_simplelink/cc32xx/Kconfig.soc.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Assignments have no effect on promptless symbols. Flagged by
https://github.com/zephyrproject-rtos/zephyr/pull/20742.
This symbol is selected by the SOC_SERIES_CC13X2_CC26X2,
SOC_SERIES_CC2650, SOC_SERIES_CC32XX, and SOC_SERIES_MSP432P4XX symbols.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Assignments have no effect on promptless symbols. Flagged by
https://github.com/zephyrproject-rtos/zephyr/pull/20742.
This symbol is selected by the SOC_SERIES_EFM32HG,
SOC_SERIES_EFM32PG12B, SOC_SERIES_EFM32WG, SOC_SERIES_EFR32FG1P, and
SOC_SERIES_EFR32MG12P symbols.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Assignments have no effect on promptless symbols. Flagged by
https://github.com/zephyrproject-rtos/zephyr/pull/20742.
This symbol is selected by SOC_SERIES_PSOC62, in
soc/arm/cypress/psoc6/Kconfig.series.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Assignments have no effect on promptless symbols. Flagged by
https://github.com/zephyrproject-rtos/zephyr/pull/20742.
This symbol is enabled through being select'ed by other symbols.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Assignments have no effect on promptless symbols. Flagged by
https://github.com/zephyrproject-rtos/zephyr/pull/20742.
This symbol is enabled through being selected by SOC_SERIES_SAM3X,
SOC_SERIES_SAM4S, and SOC_SERIES_SAME70.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Assignments have no effect on promptless symbols. Flagged by
https://github.com/zephyrproject-rtos/zephyr/pull/20742.
This symbol is enabled through being selected by SOC_MSP432P401R, in
soc/arm/ti_simplelink/msp432p4xx/Kconfig.soc.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Assignments have no effect on promptless symbols. Flagged by
https://github.com/zephyrproject-rtos/zephyr/pull/20742.
This symbol is enabled through being selected by other symbols.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Add BoosterPack connector information to the DTS of the CC1352 and
CC26x2 LaunchPad boards. This allows shields (e.g. BoosterPacks) to use
aliases for the connector interfaces and mappings for the GPIOs. This is
similar to what is being done for the Arduino connectors.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
Assignments have no effect on promptless symbols. Flagged by
https://github.com/zephyrproject-rtos/zephyr/pull/20742.
This symbol is enabled through being select'ed by SOC_SERIES_IMX_6X_M4,
SOC_SERIES_IMX7_M4, and SOC_SERIES_IMX_RT.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Assignments have no effect on promptless symbols. Flagged by
https://github.com/zephyrproject-rtos/zephyr/pull/20742.
These configuration files all enable UART_CONSOLE, which selects
CONSOLE_HAS_DRIVER.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Segger offers J-Link firmware for the debug MCU on the BBC micro:bit.
If this firmware is installed, it allows programming via nrfjprog and
JLink. Add support for this in the board.cmake.
Leave the default at pyocd, to support the factory-programmed
firmware.
With this patch, users who have installed the JLink firmware can flash
this board with nrfjprog using:
$ west flash -r nrfjprog
And can flash or debug with jlink using:
$ west flash -r jlink
$ west debug -r jlink
As usual with runner overrides, you can omit the '-r {nrfjprog,jlink}'
if BOARD_FLASH_RUNNER as a CMake variable is set to nrfjprog or
BOARD_DEBUG_RUNNER is set to jlink.
For more details on this Segger firmware, see:
https://www.segger.com/products/debug-probes/j-link/models/other-j-links/bbc-microbit-j-link-upgrade/
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Assignments have no effect on promptless symbols. Flagged by
https://github.com/zephyrproject-rtos/zephyr/pull/20742.
This symbol is enabled through being select'ed.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Defines device tree aliases for on-chip peripherals at the soc level
instead of the board level for all lpc socs. The eliminates some
duplicate code in the board level device trees, and will allow drivers
to use device-tree generated macros directly instead of through dts
fixups.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Defines device tree aliases for on-chip peripherals at the soc level
instead of the board level for all i.mx 6/7 socs. The eliminates some
duplicate code in the board level device trees, and will allow drivers
to use device-tree generated macros directly instead of through dts
fixups.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Defines device tree aliases for on-chip peripherals at the soc level
instead of the board level for all i.mx rt socs. The eliminates some
duplicate code in the board level device trees, and will allow drivers
to use device-tree generated macros directly instead of through dts
fixups.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adding Kconfig settings to warn anyone trying to build for this
platform of its pending deprecation in 2.2.0.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
The DT_INST_* defines for the PWM controllers enabled in the device
tree are always defined causing the LED pins to always be set as PWM
outputs in the pinmux. Revert to using CONFIG_PWM_* for pinmux
configuration for now.
This reverts commit eb42a24dc6.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Defines device tree aliases for on-chip peripherals at the soc level
instead of the board level for all kinetis socs. The eliminates some
duplicate code in the board level device trees, and will allow drivers
to use device-tree generated macros directly instead of through dts
fixups.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add SPI CS GPIO line to reel_board device tree. This is needed to make
the board work with Arduino SPI compatible shields.
Tested on reel_board (1507.1) and reel_board_v2 (1507.2).
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
We move the SRAM partition that is used as shared memory with
the Network MCU to the upper part of the Application MCU
memory. In this case we can allocate all lower SRAM to the
application, if we are building a Zephyr image without
support for Trusted Execution.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
With this commit we introduce SRAM partitioning for nRF5340
Application MCU. We define fixed partitions for the Secure
and the Non-Secure images, when building with trusted
execution environment enabled (Secure and Non-Secure images).
For (Secure image) builds without trusted execution environment
enabled we now allocate all available Application MCU SRAM into
the single image, except for the SRAM being used as shared memory
with the Network MCU.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
