Simple video sample getting frames from video capture device.
Tested with mimxrt1064_evk and MT9M114 sensor.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
In order to be able to run the sanity check, don't open the socket
if the test protocol is enabled.
Also add a debug print at the recv().
This commit will be dropped:
- As soon as the sanity check site accomodates
- As soon as the integration is complete
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
This commit adds sample code for bus state checking.
Printing the counter state is moved to own thread because the
ISR was blocking too long (messages were lost)
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Configures the default instance of the sdhc driver for the
mimxrt1050_evk board so applications don't have to configure it
explicitly. Similarly, enables the gpio instance required by the sdhc
driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Configures the default sdhc driver for the imx rt soc series so
applications don't have to configure it explicitly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Configures the default sdhc disk volume name to "SD" when fatfs is
enabled. This prevents applications from having to configure it
explicitly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This adds a multithreaded dumb HTTP server sample application similar
to dumb_http_server with following differences
* support both IPv4 and IPv6 simultaneously
* support multiple incoming connections
* support TLS connections
* ignore POSIX compatibility
This app can be used for testing. Note that the app will always
serve a same static HTML page to caller regardless of HTTP request
parameters.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Key overwrite feature allows to overwrite old pairing key
records when key storage is full and a new pairing request occurs,
or new keys are distributed. If enabled when key storage is full and
a keys storage slot is requested, the oldest keys added will be
removed. So new devices can be paired with no limitations and no need
to determine, which devices should be unpaired to free key storage
space explicitly in application. To enable the feature set
CONFIG_BT_KEYS_OVERWRITE_OLDEST=y.
Oldest keys are determined by minimum value of up-counting aging
counter. If you set CONFIG_BT_KEYS_SAVE_AGING_COUNTER_ON_PAIRING=y
aging counter values will be updated each time the secure connection
is established. This might increase flash wear out if at least two
secure connections are established and shut down periodically. When
the option disabled aging counter is still updated on each new secure
connection, but not stored to flash.
Signed-off-by: Sergiy Nikolayenko <sergiy_nikolayenko@jabil.com>
This sensor defaults to no trigger, in which case no observations will
be read from the device. Set to use the work queue (global) trigger.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
With the changes in PR #19836 applications now need to explicitly
include hci.h to use defines from it. Fix two sample/tests apps which
were missing this.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For Genric OnPowerUp equal to 0x02 (Restore):
If a transition was in progress when powered down, the element
restores the target state when powered up. Otherwise the element
restores the state it was in when powered down.
This commit implements above mentioned logic.
Signed-off-by: Vikrant More <vikrant8051@gmail.com>
This illustrates how a keyboard matrix (laptop keyboard) reports
key events to a user application. In addition, it shows how to
handle the typematic rate and delay from user space.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
Some of the socket samples had wrong information about what default
board to use. Currently there is no default board and user must
select the board when building the application.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The Peripheral Device Information Service (DIS) sample implements it's
own custom settings backend in order to load runtime settings.
This results in errors when the BT stack tries to save entries through
the custom handler since no save handler exists.
Error messages:
- bt_settings: Failed to save ID (err -2)
- bt_gatt: Failed to save Database Hash (err -2)
Since this is not a sample of how to do custom settings backend it is
best simply to remove using the custom backend, as it is not required
in order to load runtime settings.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
samples/bluetooth/peripheral couldn't build on nucleo_f429zi
since settings dependency on flash erase bock size.
On this series, flash erase are done per sector with sector
having varying size, so erase block size can't be used directly.
This has to be sorted, but for now nucleo_f429zi is removed from
sample withelist to unlock CI.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The hexdump was earlier printed using 8 bytes in one line like this
[00:00:00.131,143] <wrn> sample_instance.inst2: Example of hexdump:
01 02 03 04 05 06 07 08 |........
09 0a 0b 0c 0d 0e 0f 10 |........
11 12 13 14 15 16 17 18 |........
19 1a 1b 1c 1d 1e 1f 20 |.......
21 22 |!"
This is not utilizing the width of the output best way possible.
Better utilization of the output is to print 16 bytes in one line
like this:
[00:00:00.131,136] <wrn> sample_instance.inst2: Example of hexdump:
01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 |........ ........
11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f 20 |........ .......
21 22 |!"
In order to make it easier to find / calculate the bytes in the
output, print the output bytes in 8 byte groups.
This has the benefit that it is easier to map the Zephyr hex output
to Wireshark output which prints the bytes like this.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Re-run with updated script to convert integer literal delay arguments
to k_thread_create and K_THREAD_DEFINE to use the standard timeout
macros.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Re-run with updated script to convert integer literal delay arguments to
k_sleep to use the standard timeout macros.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
found some references to files (via :zephyr_file: and :zephyr-app:) that
were moved, so the links were broken
Fixes: #19660
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
DTSpec writes this as a single word, presumably to make it easier to
grep for / more precise. Follow along in the rest of the docs now that
our main DT docs page agrees with this usage.
Signed-off-by: Marti Bolivar <marti.bolivar@nordicsemi.no>
Instead of printk(), use logging macros so that all the output
from IP stack and sample is nicely interleaved.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Network shell is useful to have in order to debug things so
enabling it for this sample application.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
