Removed redundant coding which was related to old implementation.
Now Server will publish the new state information to the model’s Publish
Address only when there is mismatch between target & current values.
Signed-off-by: Vikrant More <vikrant8051@gmail.com>
Fix build reply function. The sample uses return value
from net_pkt_read() to determine data length,
but the return value is 0 on success.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Add internal API to enter and exit deep power-down mode. Add Kconfig
option to return to DPD whenever device is not active.
When device power management becomes more mature it should be possible
to implement it, which would allow use of DPD without having to enter
and exit DPD between consecutive transactions.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
This commit converts the existing hcm5883l 3-axis magnetometer
driver to use device tree for the I2C and GPIO selection.
It also adds a basic sample application for this sensor, using the
frdm-k64f development board to demonstrate how the interrupt
GPIO pin and I2C bus can be selected.
Signed-off-by: Kevin Townsend <kevin@ktownsend.com>
Add a special target that's marked build_only so the BLE SW LL
implementation on VEGABoard is built daily. This helps ensuring
that it doesn't get inadvertedly broken by subsequent updates.
The name of the target is peripheral_hr_rv32m1_vega_ri5cy
and it can be run with the following command:
sanitycheck -v --all -p rv32m1_vega_ri5cy \
-x=CMAKE_REQUIRED_FLAGS=-Wl,-dT=/dev/null \
--test samples/bluetooth/peripheral_hr/\
sample.bluetooth.peripheral_hr_rv32m1_vega_ri5cy
Note: The extra CMake flags are required if running with the official
VEGABoard compiler, due to this linker issue:
https://github.com/pulp-platform/pulpino/issues/240
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Add the required specific HW configuration for SW defined
BLE LL on RV32M1 SoC, by means of DTS overlays:
- enable INTMUX0 channels 2 & 3
- route Generic FSK RF0 interrupt to INTMUX channel 3
- route LPTMR1 interrupt to INTMUX channel 2
This change is done for all Bluetooth samples that are intended to
run on RV32M1 using BLE SW LL.
Signed-off-by: George Stefan <george.stefan@nxp.com>
Signed-off-by: Radu Alexe <radu.alexe@nxp.com>
Signed-off-by: Ionut Ursescu <ionut.ursescu@nxp.com>
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Complement GPIOTE HAL function calls with the NRF_GPIOTE parameter.
Update nrfx_gpiote_init() function call with the newly introduced
parameter.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Convert bmg160 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert bmm150 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert max44009 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert mcp9808 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert sx9500 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert tmp112 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert th02 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Mark the old time conversion APIs deprecated, leave compatibility
macros in place, and replace all usage with the new API.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Several macros were documented as deprecated but lacked the
infrastructure to produce deprecation warnings. Add the deprecation
marker, and fix the in-tree references to the deprecated spellings.
Note that one non-deprecated macro should have been deprecated, and
is, referring to a newly added line control bit.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Adds the model extension concept to the access layer, as described in
the Mesh Profile Specification, Section 2.3.6. Extensions are
implemented as a tree, using two pointers in each model:
The extends pointer points to the first extended model, and the next
pointer points to the next sibling or (if the NEXT_IS_PARENT flag is
set) the parent model in the tree, forming a cyclical "Left-child
right-sibling" (LCRS) tree. The tree root can be obtained by calling
bt_mesh_model_root_get(), and the extended models can be walked by
calling bt_mesh_model_tree_walk().
According to the Mesh Profile Specification Section 4.2.3, all models in
the same extension tree share one subscription list per element. This is
implemented by walking the model's extension tree, and pooling the
subscription lists of all models in the same element into one. If the
config server adds a subscription to a model, it may be stored in any of
the model tree's models' subscription lists. No two models in the same
extension tree and element will have duplicate groups listed. This
allows us to increase extended models' capacity for subscriptions
significantly.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Replace CONFIG_WDT_0_NAME with DT_ALIAS_WATCHDOG_0_LABEL in samples and
test code. Now that all drivers are DT aware we don't ever set the
Kconfig option.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update shield description and sample to allow testing of LIS3MDL
sensor IRQ pin.
Update sample yaml file to state dependency on arduino_gpio.
Additionally, fix redundant line in sample yaml
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit removes the disco sample because it is basically
the same as blinky but with two LESs and adds no new value
to the samples.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Previous defconfig for dma is DMA_STM32F4X in this board, while the new
generic driver uses DMA_STM32 to enable DMA support, and also dma driver
of stm32 now needs HEAP_MEM_POOL_SIZE to be big enough to hold dma
stream instances.
Additional .conf files are added for also adding HEAP_MEM_POOL_SIZE
configuration to two test cases.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
As the iPerf2 protocol is not documented properly, depend on
exact iPerf 2.0.5 version when testing.
Fixes#20313
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Enable the MX25R32 SPI NOR Flash on the VEGAboard and provide board
config file for the spi_flash sample.
Signed-off-by: Karsten Koenig <karsten.koenig.030@gmail.com>
convert sample and test yaml filters that utilize a DT_ define to
instead use a dt_ function. The intent is to remove the Kconfig
generated DT defines and just make directy queries into the device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move _LINKER and _ASMLANGUAGE to target.cmake because of how we pick the
linker script that might be used. This way regardless of how or where a
linker.ld gets included we will always set _LINKER & _ASMLANGUAGE (so
any header that needs check based on those defines they can,
specifically generated_dts_board.h)
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This sample showcases efficient utilization of SMP system
with processing of independent resource-hungry workloads.
With no cross-dependencies between workers and no usage of shared
resources (during heavy-lifting itself) we may demonstrate almost
linear scaling of efficiency. I.e. 2 cores do the same amount of
calculations twice faster than only 1 core. 4 cores complete
the same calculations 2 times faster than 2 cores.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
We try to demonstrate some concepts for user mode:
- Multiple logical applications, each with their own memory
domain
- Creation of a sys_mem_pool and assignment to a memory
partition
- Use of APIs like k_queue_alloc_append() which require
thread resource pools to be configured
- Management of permissions for kernel objects and drivers
- Show how application-specific system calls are defined
- Show IPC between ISR and application (using k_msgq) and
application-to-application IPC (using k_queue)
Fixes: #14683
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
add sample for syst format output to prove the output can be
decoded by the existing decoder.
Fixes: #19841.
Signed-off-by: Wentong Wu <wentong.wu@intel.com>
Quit the accept loop if there is a socket related error as there
is no point of continuing in this case.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Achieved using CONFIG_NET_CONFIG_CLOCK_SNTP_INIT option, i.e. querying
time over network using SNTP.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
PSK support is added to echo-client.c and echo-server.c.
If enabled, a header is included which contains the PSK.
If the default dummy PSK header is used, a warning is issued.
The header can be changed via Kconfig.
Signed-off-by: Torstein Grindvik <torstein.grindvik@nordicsemi.no>
Not a top-level zephyr core API and tied to third party environment, so
move it to where the code is in lib/updatehub.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
There are two set of code supporting x86_64: x86_64 using x32 ABI,
and x86 long mode, and this consolidates both into one x86_64
architecture and SoC supporting truly 64-bit mode.
() Removes the x86_64:x32 architecture and SoC, and replaces
them with the existing x86 long mode arch and SoC.
() Replace qemu_x86_64 with qemu_x86_long as qemu_x86_64.
() Updates samples and tests to remove reference to
qemu_x86_long.
() Renames CONFIG_X86_LONGMODE to CONFIG_X86_64.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This samples captures frames from video capture device (in any format),
and sends them to its TCP client.
Tested with:
- mimxrt1064 + MT9M114 video sensor.
- Gstreamer 1.8.3 running on host
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
