Add timer and pwm nodes. The structure follows a similar approach to the
one used by STM32. Timer nodes store all timer information (e.g.
pre-scaler), whereas the pwm nodes are children of the timer node
indicating a specialization of the multiple timer functionalities.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
HSE clock frequency value depends on target.
It can't be defaulted.
Remove this property to ensure it is set properly for each target.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
NPCX7/9 has a different ADC register structure. NPCX7 has 3 threshold
detectors from offset 0x14 & has 10 input channels. NPCX9 has 6
threshold detectors from offset 0x60 & has 12 input channels.
This commit fixes the NPCX ADC register structure.
Signed-off-by: Wealian Liao <WHLIAO@nuvoton.com>
Kconfig options will anyway enable/disable the driver relevantly.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Assign unique memory-region attribute values for both OCM
memory areas so that the lower region starting at address 0
is identified as OCM_LOW, while the alternate location for
the OCM memory is identified as OCM_HIGH.
The updated linker command file will use those identifiers
for OCM section mapping based on which of the two OCM areas
is marked as 'chosen' at the board level.
Signed-off-by: Immo Birnbaum <Immo.Birnbaum@weidmueller.com>
YAML description file for the On-Chip Memory of the Xilinx
Zynq-7000, DT identifier "xlnx,zynq-ocm".
Signed-off-by: Immo Birnbaum <Immo.Birnbaum@weidmueller.com>
- The gpio dt-bindings were not included
- gpio-controller property was not present in gpio nodes
- number of gpio cells was not present in gpio nodes
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
- The gpio dt-bindings were not included
- gpio-controller property was not present in gpio nodes
- number of gpio cells was not present in gpio nodes
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Add DT node for EXTI (External Interrupt Controller). Only line
interrupts added for now (used for GPIO interrupts).
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Add DT node for EXTI (External Interrupt Controller). Only line
interrupts added for now (used for GPIO interrupts).
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
The spi-bus-width property provides information if the target system
has all SIO[0123] pins connected to NOR flash memory.
It must be equal to 4 to enable QSPI 4 IO operation.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Some flash memories connected to QUADSPI IP block on stm32[fh]7 devices
require proper reset pulse before configuration.
This patch adds two new properties - the 'reset-gpios' phandle,
which allows specifying GPIO pin for RESETn pulse and
'reset-gpios-duration', which provides the time (in ms) for reset
duration.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The 'flash-id' property defines the number of QSPI's dedicated GPIO
bank (and flash ID), which will be used to communicate with flash
memory.
For example, on stm32h7xx it is possible to use 'quadspi_bk1_*' and
'quadspi_bk2_*' set of pins, so one may need to select between them
when required.
By default - pins from 'quadspi_bk1_*' bank are used, so the
'flash-id = <2>;' property, when your use case (e.g. PCB design)
requires it, forces usage of 'quadspi_bk2_*' pins.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Now in Zephyr only stm32f7 processors have by default provided support
for QSPI IP block.
The same IP block is also available in stm32h7 (with different offsets),
so proper DTS description shall be provided as well for it.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
In npcx_itim_evt_isr, it updates the cyc_sys_announced variable and
then calls sys_clock_announce() to update the kernel curr_tick variable.
If an ISR handler with higher priority preempts the timer ISR after the
sys_clock_announce is updated and before the sys_clock_announce() is
called, it will read the wrong time when calling k_uptime_get() because
the cyc_sys_announced and the curr_tick are not synchronized.
The commit fixes the problem by raising the timer's interrupt priority
to the highest one (i.e. 1 in npcx's configuration).
This commit also moves the computation of the delta cycle inside the
spinlock in sys_clock_elapsed() to prevent another potential racing
condition.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
Signed-off-by: Wealian Liao <WHLIAO@nuvoton.com>
Convert the CAN loopback driver from being configured via Kconfig to
multi-instance configured via devicetree.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The syscall_perf test cannot be built successfully due to region RAM
overflow on qemu_riscv32_xip and hifive1_revb. The dtim is only 16KB,
To reduce the main stack size to make it can be built successfully.
Base on the spec(fe310-g002-manual-v1p1.pdf), the size of itim should
be 8KB. Modify the definition in its DTS file.
And it also fix some of the gcc warning when testing it by twister.
This PR partially fixes#41399.
Signed-off-by: Enjia Mai <enjia.mai@intel.com>
The vnd,gpio-device compatible is now used by the test GPIO driver
(CONFIG_GPIO_TEST) introduced in #41387. This means that we can't define
new devices with this compatible when CONFIG_GPIO=y.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
The pinsN group name can be a confusing in some circumstances, so change
it to groupN. Some platforms (e.g. nrf or gd32) are already using
groupN. Documentation and API tests have been updated.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
If there are no console messages input at an interval of 15
seconds, the system will be able to enter suspend mode.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
So far driver was using SENSE mechanism for all or none edge
interrupts. This was not convenient since in some modules may
require IN event to be used and other did not. Converting it to
use a mask specified in the device tree. Pins indicated in the
mask will use sensing.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Add a new DT property named "pixel-group-size" that allows users to
configure the driver to refresh the matrix by illuminating multiple
LEDs in particular rows simultaneously. This way the maximum possible
brightness of the LEDs can be increased (as they can be lit longer)
and the timer interrupt handler is executed less frequently, what
results in decreased CPU load, but more GPIOTE/PPI channels needs to
be allocated if the PWM peripheral cannot be used. Thus, it is left
to users to select the configuration that suits them best.
Update definitions of both the bbc_microbit boards with this new
property, using the maximum available group size (to achieve maximum
possible brightness). For v2, no new resources are used (only all
channels in the already used PWM peripheral are now utilized).
For v1, two more GPIOTE and PPI channels are allocated.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Some STM32 series need to configure health test register
for proper RNG behavior.
In addition, some also require to write a Magic number
before writing the configuration.
Note: on stm32h7 not all product lines support this configuration.
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
Some STM32 series need to configure health test register
for proper RNG behavior.
In addition, some also require to write a Magic number
before writing the configuration.
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
- Supporting multiple instances of ivShMem virtual devices.
- Introduces DT based configuration for ivShMem devices.
- Add DTS overlay file to test new multiple ivshmem instance capability.
- Enable BDF unspecified device initialization.
(limited to one instance. An improved version of pcie_bdf_lookup()
will come soon that fixes this limitation)
- Make PCIE DTS file macros available for a proper ivshmem device
properties parsing.
Sample for dts file:
pcie0 {
label = "PCIE_0";
#address-cells = <1>;
#size-cells = <1>;
compatible = "intel,pcie";
ranges;
ivshmem0: ivshmem@800 {
compatible = "qemu,ivshmem";
reg = <PCIE_BDF_NONE PCIE_ID(0x1af4,0x1110)>;
label = "IVSHMEM";
status = "okay";
};
};
Signed-off-by: Michael Schmidt <michael1.schmidt@intel.com>
Modifying configuration to enable with gd32vf103
- Add usart definition to devicetree.
- Define USART_STAT as alias of USART_STAT0 if not defined it.
- Enable USART if SOC_SERIES_RISCV_GIGADEVICE_GD32VF103.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Change the settings to support pinctrl on the GD32VF103.
- Split soc/arm/gigadevice/common/pinctrl_soc.h
and put it into include/dt-bindings.
- Leave some definitions that can't handle with device tree compiler
in pinctrl_soc.h.
- Remove dependency to SOC_FAMILY_GD32 because always enabled it
if GD32_HAS_AF(IO)_PINMAX was selected.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
GD32V SoC uses divided clock from core-clock for machine timer clock.
Add config of clock divide factor to support GD32V.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
As Nordic SPI, I2C and UART buses can act as both slave and master,
these nodes can have different compatible properties, and are annotated
with a comment, instead of a compatible property. This forces boards to
put compatible properties in their definitions, which is unnecessary
boilerplate for most boards, as most boards acts as masters on these
buses.
Set master mode by default for these buses, to reduce boilerplate and
potential errors in board definitions. Boards that need to act as slave
nodes will just continue to override the compatible properties.
Likewise, existing boards that override this compatible property with a
master binding will not be affected by this change.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
The stm32u5 device has a single iwdg node entry and label
without any need for interrupt. Even if it exists the irq entry
is not required.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Implemented driver for the simcom sim7080 modem.
This driver features Socket offloading, TCP, UDP, DNS,
SMS, GPS and FTP.
Signed-off-by: Lukas Gehreke <lk.gehreke@gmail.com>
Remove the requirement for specifying #address-cells and #size-cells
properties for CAN controller devicetree nodes.
CAN controllers do not have a common concept of devicetree child nodes
and thus have no need for these properties. This is in line with
upstream Linux kernel devicetree bindings.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
NPCX series used npcx-lvol-ctrl-map to record the GPIO & low voltage
control register map. However, GPIOE3 was configured as GPIOE6, which
is a non-existed pin. This commit fixes the GPIOE3 low voltage control
map.
Signed-off-by: Wealian Liao <WHLIAO@nuvoton.com>
Move odr and range properties for both accelerometer and gyro
from Kconfigs to Device Tree.
Fixes#41117
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Fix the yaml dts multi-line property description in the following
(expected) way:
description: |
PUT_TEXT_HERE
Signed-off-by: Armando Visconti <armando.visconti@st.com>
