MCUX PWM driver used hardcoded clock source. update driver to use clock
bindings to determine PWM peripheral clock frequency.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Adds optional device tree properties to insert delays between spi chip
select assert/deassert and the clock edges, and also between spi
frames and transfers to the mcux flexcomm spi driver. If the properties
are not set, no additional delay is inserted.
Verified expected behavior on mimxrt685_evk and check with a scope
that the pre- and post-delay could be changed from the device tree
properties.
Signed-off-by: Bryce Wilkins <bryce.wilkins@gmail.com>
This commit adds support for IMX6SX PWM.
The PWM module is the same module present on the IMX7D and so dts
bindings has been renamed following the one present on linux.
Signed-off-by: Antonio Tessarolo <anthonytexdev@gmail.com>
Most of the time SPI devices use TI's frame format. But some may use
Motorola's. This is already taken care of in the SPI API and now it will
be possible to select the right format from DTS. Like:
...
frame-format = <SPI_FRAME_FORMAT_MOTOROLA>;
...
This is only meant to be used for devices supporting both formats (so
the format is not hard-coded in the driver) and selected by hardware
configuration or else. Which, in such case, it will need to use
DT_INST_PROP(<instance number>, frame-format) macro call to retrieve
the property value. Others can fully ignore it.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Software reset is already implemented in the driver when the
`reset_gpio` is not defined. However it could not be activated
because the `reset_gpio` is a required field in the DTS
binding.
Signed-off-by: Casper Meijn <casper@meijn.net>
This patch adds support for the new pinctrl API to the UARTE driver. The
old pin property based solution is still kept so that users have time to
transition to the new model.
Notes:
- Some build assertions cannot be performed since the driver does not
have direct access to pin settings anymore. As a result user will not
be notified if HWFC is enabled but RTS/CTS pins are not configured.
- Hardware flow control can be enabled regardless of pin configuration,
it is now up to the user to configure RTS/CTS pins in DT.
- Some RX enable checks that were performed using pin information has
been replaced with a DT property that informs if RX is enabled or not.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add initial support for nRF pin controller driver. The implementation in
this patch does not yet support any peripheral. Only states
representation and basic driver functionality is introduced.
Note:
The nrf_pin_configure function has been marked as __unused since it may
not be used in certain scenarios until all peripherals are supported by
the pinctrl driver. For example, if only UART/E is supported but the
board does not enable UART, the function will never get called. However,
that board will likely have other peripherals that will gain support in
the future.
Thanks to Marti Bolivar for bindings documentation.
Co-authored-by: Marti Bolivar <marti.bolivar@nordicsemi.no>
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Now that STM32 drivers are using pinctrl API, set pintrl-0 and
pintrl-names properties as required in order to report malformed
nodes description soon at build stage and avoid cryptic
DT api build error messages.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use the new pinctrl API to configure pins.
Since STM32F1 series require pinctrl option and required register
address is parent timer address in place of own node register address,
use PINCTRL_DT_INST_CUSTOM_REG_DEFINE in place of usual
PINCTRL_DT_INST_DEFINE for this specific series.
Additionally, remove the automatic selection of PINMUX API.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use the new pinctrl API to configure pins.
Additionally, rename usb_pinctrl to usb_pcfg to better fit
new pinctrl API.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add the pinctrl state name (default) for the CAN peripherals.
Changes performed based on the script proposed in
"boards: arm: stm32: add pinctrl state name for UART peripheral"
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add the pinctrl state name (default) for the I2C peripherals.
Changes performed based on the script proposed in
"boards: arm: stm32: add pinctrl state name for UART peripheral"
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use nrfx_gpiote and nrfx_ppi allocators to allocate channels
at runtime instead of fixed, device-tree based allocation which
is harder to maintain.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Add bindings for a generic PCIe Controller in ECAM mode.
ECAM stands for PCI Express Enhanced Configuration Access Mechanism
where the PCIe config space is flat memory-mapped.
An optional msi-parent phandle is added to link to an optional
MSI/MSI-X Interrupt Message Translation HW component.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The qemu arm64 virt machine PCIe controller config space needs a
64bit adressing, so switch the entire qemu-virt-a53 and
qemu_cortex_a53 board dts to address-cells & size-cells to 2
to accommodate for 64bit addresses.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
These registers were hardwired in the platform layer. Move to
devicetree, via a struct interface that looks like the pre-existing
shim layer.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
These registers are identical on all platforms, the only difference
being that cAVS 1.5 places them at a different address.
Create a devicetree node to track the register block, and replace the
platform header code with a global API defined once (it works like the
pre-existing shim struct).
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Each platform was defining its own shim.h header, with slightly
variant field definitions, for a register block that is almost
completely compatible between versions. This is made worse by the
fact that these represent an API imported fairly early from SOF, the
upstream version of which has since diverged.
Move the existing shim struct into a header ("cavs-shim.h") of its
own, remove a bunch of unused symbols, fill in definitions for some
registers that were left out, correct naming to match the hardware
docs in a few places, make sure all hardware dependencies are source
from devicetree only, and modify existing usage to use the new API
exclusively.
Interestingly this leaves the older shim.h header in place, as it
turns out to contain definitions for a bunch of things that were never
part of the shim register block. Those will be unified in separate
patches.
Finally: note that the existing IPM_CAVS_IDC driver (soon to be
removed from all the intel_adsp soc's) is still using the old API, so
redeclare the minimal subset that it needs for the benefit of the
platforms in transition.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
This is dead code. It's based on the cAVS "IPC" mechanism to allow
communication to and from the host CPU. But there is no test rig in
the Zephyr tree for the protocol defined. And in fact the only
Zephyr-based user of the IPC mechanism (Sound Open Firmware) has its
own IPC driver and speaks its own protocol with the host kernel. That
driver needs to migrate into Zephyr soon and this legacy bit is just
confusing.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Introduce a new RPMsg with static VRINGs backend. This new backend makes
easy to generate and use IPC instances backed by OpenAMP using the DT.
Each instance is defined in the DT as (for example):
ipc: ipc {
compatible = "zephyr,ipc-openamp-static-vrings";
shm = <&sram_ipc0>;
mboxes = <&mbox 0>, <&mbox 1>;
mbox-names = "tx", "rx";
role = "primary";
status = "okay";
};
It is then possible to register an send data through endpoints using the
IPC service APIs.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
* With existence of Adafruit Qt Py boards, and upcoming wireless
Xiao from Seeeduino, define nexus node and peripheral node
labels for use with shields that accept any Xiao format board.
* Adds `&xiao_d`, `&xiao_spi`, `&xiao_i2c` and `&xiao_serial` generic
node labels.
* Add new 'seeed-xioa-header.yaml` to document new nexus node.
Signed-off-by: Peter Johanson <peter@peterjohanson.com>
Add a pin control driver for GD32 SoCs using the AFIO model.
Thanks to Gerson Fernando Budke for testing and implementation
suggestions.
Co-authored-by: Gerson Fernando Budke <gerson.budke@atl-electronics.com>
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
