We have drivers for "nxp,lpc-rtc" and "zephyr,native-posix-counter"
devicetree compatibles, however we had no bindings for them. Add
simple bindings
Signed-off-by: Kumar Gala <galak@kernel.org>
Two files ending with yml while the rest is ending with yaml, just
rename those two to avoid special handling.
Fixes documentation build.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This CL adds a DT node, 'power_leakage_io', which property,
'leak-gpios', contains GPIOs that have leakage current. In oerder to get
better power consumption, npcx power driver will disable the connections
between these io pads and input buffers before entering deep sleep.
Then, restore the connections after ec wakes up.
The users can overwrite this property at board DT file. Here is an
example:
&power_leakage_io {
leak-gpios = <&gpio0 0 0
&gpiob 1 0>;
};
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This CL configures low-voltage (1.8V) detection via GPIO driver with
GPIO_VOLTAGE_1P8 flag. It also adds support for this flag in
pin_get_config() function.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Cleanup npcx low-voltage (1.8V) detection configuration. It removes
unused soc utilities, macros, and DT node. We will configure this
feature by GPIO driver with GPIO_VOLTAGE_1P8 flag later.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
ITE EC chip it81202 and it81302 both have embedded integrated
pd module (support two usbpd ports), this is different from
standalone TCPC. To prevent cc pins leakage, we disable not
active ITE USBPD port cc modules, then cc pins can be used
as gpio if needed.
Signed-off-by: Ruibin Chang <Ruibin.Chang@ite.com.tw>
Move the RX (MISO) delaying capability information to Devicetree. It is
done using 2 properties:
- rx-delay-supported: enabled on SPI nodes that support delaying RX.
This property can be used by the driver to determine if this
capability is supported or not on a given instance.
- rx-delay: the actual RX delay value
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Specify the overrun character in Devicetree. Since 0xFF is the most
common value, DT property contains such default.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Devicetree is the natural place to describe hardware, so move the
maximum frequency the SPI can work with to Devicetree instead of relying
on values from HAL.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Some panels using this driver don't provide tcon/cdi/pwr/softstart
values in their reference code. It is normally expected that the right
values will be loaded from OTP in such cases. Make these values
optional to support such panels.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Introduce a generated Kconfig.dts that sets a Kconfig symbol for
every compatible.
* We set DT_HAS_<compat>_ENABLED if the devicetree has a node with
<compat> enabled. (status is okay...)
We can then use the Kconfig symbol in driver Kconfig to determine
if the driver should be available, and thus enabled by default.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
Any project with Kconfig option CONFIG_LEGACY_INCLUDE_PATH set to n
couldn't be built because some files were missing zephyr/ prefix in
includes
Re-run the migrate_includes.py script to fix all legacy include paths
Signed-off-by: Tomislav Milkovic <milkovic@byte-lab.com>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
Add configuration for SPI connected ADXL345 accelarator sensor
as adi,adxl345-spi.yaml.
Rename original adi,adxl345.yaml that configured for I2C
rename to adi,adxl345-i2c.yaml.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Implement support for SAMR34 and SAMR35 parts, tested on a SAMR34
Xplained Pro dev board. Confirmed operational peripherals: UART, GPIO,
PWM, ADC.
NOTE: The SAMR34 datasheet lists NVIC line 20 for the ADC's interrupt,
but the SAML21 datasheet gives line 22. It appears that the SAMR34 sheet
is incorrect (the ADC doesn't function with line 20), and as such, I have
also omitted the adjustments for TC4 and AC...
Signed-off-by: Attie Grande <attie.grande@argentum-systems.co.uk>
Implement support for SAML21 parts, tested on a SAML21 Xplained Pro dev
board. Confirmed operational peripherals: UART, GPIO, PWM, ADC.
Signed-off-by: Attie Grande <attie.grande@argentum-systems.co.uk>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
The built-in USB serial peripheral is a virtual serial and does not
allow to be configured like a normal UART.
Removing the unused UART config parameters.
Also reducing initialization to single-instance only.
Signed-off-by: Martin Jäger <martin@libre.solar>
Remove 'label' property from SDHC nodes. We can use variants of
DEVICE_DT_GET to get access to a device pointer for use in an
application.
Signed-off-by: Kumar Gala <galak@kernel.org>
The 'nxp,imx-flexspi-device' compatible that was specified in
the YAML file is not an actual compatible that is intented to be
used. Instead the YAML file is included in other YAML files
that set specific compatible.
If the 'nxp,imx-flexspi-device' was used we'd actually get an error
from edtlib because of having the same compatible specified by
two different YAML files.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
Clean up unused psl functions in scfg.c, unused DT macros, unused psl DT
nodes and related yaml files. Currently, PSL pad configurations are made
by pinctrl mechanism. Please refer
https://issuetracker.google.com/234861079 for more detail.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
HDA is a common IP used across the entire ADSP line and deserves
a name respecting that alongside similiar IP drivers such as the
ADSP GPDMA driver.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Add adsp-imr binding. This memory type is being used in intel adsp dts
but this binding was missing.
Co-authored-by: Marcin Szkudlinski <marcin.szkudlinski@intel.com>
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
All in tree device drivers on a bus use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
Add simple clock control node in devicetree for beetle to handle
relationship between drivers (uart, timers, gpio) and clock controller
device.
Signed-off-by: Kumar Gala <galak@kernel.org>
