Remove the test clock out Kconfig from SoC level. Instead use
device tree PINCTRL entry with updated clock control driver.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Add support for Microchip MEC15xx to the XEC clock control driver.
MEC15xx 32KHz clock support uses the same 32KHz source for both the
PLL and peripherals. MEC152x does not include the PCR clock monitor
present in MEC172x. MEC15xx and MEC172x support internal silicon
oscillator, parallel and single ended crystal inputs, and the
32KHZ_PIN input. MEC152x supports fall back to internal silicon
OSC when VTR and 32KHZ_PIN are turned off. Therefore in MEC152x the
internal silicon oscillator can only be disabled if using an external
32KHz which is always on. For MEC152x the driver will only use the
PLL source clock device tree value.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Fix Microchip XEC clock control driver single-ended XTAL2 pin
initialization. Add support for external 32KHZ_IN pin as a
clock source including PINTRL to switch the GPIO to 32KHZ_IN
function. Add device tree option to disable internal silicon
oscillator if it is not required by the configuration. Add
device tree tuning options based on crystal and board layout.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Add initial support for gd32l23x series. gd32l23x used Cortex-M23, based
on ARMv8-M baseline, implement the System Timer.
Signed-off-by: HaiLong Yang <hailong.yang@brainco.cn>
Enable RTU.SWT (Real-Time Unit.Software Watchdog Timer) instances on
s32z270dc2_r52 boards. Module clock frequency is fixed to 48 Mhz.
Signed-off-by: Quang Bui Trong <quang.buitrong@nxp.com>
Add missing I2C clock sources for STM32F303 & F373.
Add a comment for all STM32F3 I2Cx and for STM32F0 I2C1 that the clock
source should always be defined.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Add config cell property to gd,gd32-dma.
For supporting hardware variation, Splitting base definition
to gd,gd32-dma-base.yaml.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Define SYSCLK as the default I2C source clock for I2C1 on STM32F0x
and all I2Cx on STM32F3x.
On most series, the default I2C clock source (when it exists) is PCLK.
This clock does not exist as I2C clock source on FO & F3 and the default
one is HSI. Since HSI is not necessarily enabled we explicitly set it
to SYSCLK instead.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Include the new clock file dedicated for STM32F7 instead of the F4 one
previously used.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
peripheral-id property should be eventually removed.
For now set it as optional and allow skipping the usage
in UART driver.
Signed-off-by: Pawel Czarnecki <pczarnecki@antmicro.com>
peripheral-id property should be eventually removed entirely.
For now set it as optional and allow skipping the usage
in GPIO driver.
Signed-off-by: Pawel Czarnecki <pczarnecki@antmicro.com>
HAL update affects also EFR32MG21 SoC. Because of that we need to
update the reg addresses in DTS.
Signed-off-by: Pawel Czarnecki <pczarnecki@antmicro.com>
This commit adds support for Silicon Labs EFR32BG22 SoC.
Co-authored-by: Mateusz Sierszulski <msierszulski@antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
This commit adds initial support for Silabs Real-Time counter
Co-authored-by: Filip Kokosinski <fkokosinski@antmicro.com>
Signed-off-by: Mateusz Sierszulski <msierszulski@antmicro.com>
This commit adds a series of driver-related changes to
Gecko pinctrl.
Co-authored-by: Mateusz Sierszulski <msierszulski@antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
This commit adds initial support for gecko pinctrl driver
Co-authored-by: Mateusz Sierszulski <msierszulski@antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
The ADC module has four conversion groups, each one is set up as a zephyr
device. The start-up calibration is initiated globally for all groups
and it is run in each device init function. The ADC module supports post
calibration per group. Post calibration is run automatically after each
group acquires the samples.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
Add virtual memory entry in dt to use as virtual space
regions for aplication.
Add virtual memory definition in adsp_memory.h
Signed-off-by: Jakub Dabek <jakub.dabek@intel.com>
Add FFF-based fake regulator driver. This driver can be used as a stub
or mock in testing.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
These inherited properties from Linux bindings are not supported yet.
The reason for the removal is because regulator-couple-with requires
definition of #cells spec, unless bindings explicitely ban the property
or use allowlist.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add i.MX93 Cortex-A Core support on Zephyr.
i.MX 93 applications processors deliver efficient machine learning
(ML) acceleration and advanced security with integrated EdgeLock
secure enclave to support energy-efficient edge computing.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Adds two additional alh2 and alh3 "devices" to already defined
alh0 and alh1. This (seems) is a temporarily solution as
the hardware actually supports 16 streams and future update
to device tree is required.
Signed-off-by: Serhiy Katsyuba <serhiy.katsyuba@intel.com>
Add support for virtual USB host controller intended for use
together with virtual bus and virtual device controllers.
This driver is not an emulation of any real host controller.
The driver has initial support for handling control and bulk
transfers.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Add support for virtual USB device controller intended for use
by virtual bus and virtual UHC controllers. This driver is not
an emulation of any real host controller.
The driver has initial support for handling control and bulk
transfers.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Add common layer of UHC API and MAX3421E host controller driver.
This implements the bare minimum necessary to communicate with
one peripheral device.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Assigning power domain to the GP DMA.
NOTE: Only controllers 1 and 2 are under IO_0 domain, controller 0 is
under HUB-ULP domain.
Signed-off-by: Tomasz Leman <tomasz.m.leman@intel.com>
Support for the measuring the CPU die temperature
for the ESP32 targets S2,C3. The ESP32 support
was ommited due to lack of offset calibration.
Signed-off-by: Marek Matej <marek.matej@espressif.com>
Serial speeds listed in device tree did not reflect
what driver supports.
2M and 500K were missing while
1200, 2400 and 460800 were present while not supported.
This change synchronized dts with driver code:
drivers/serial/uart_smartbond.c
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
PCA9420 PMIC offers of multiple operation states, or DVS (Dynamic
Voltage Scaling). Such states may be automatically changed by hardware
using MODESEL0/1 pins. Certain MCUs allow to automatically configure
certain output pins when entering low power modes so that PMIC state is
changed without software intervention. This means that application just
needs to configure the voltages for each state using
`nxp,modeN-microvolt`, set `nxp,enable-modesel-pins` in devicetree and
forget about configuring regulators.
This patch introduces a new _parent_ API to expose such functionality in
a vendor agnostic way. Consider this API as experimental for now, until
we have other usecases.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Most of devicetree properties for regulator, such as:
- regulator-min/max-microvolt
- regulator-min/max-microamp
- regulator-allowed-modes
- etc.
Are meant to specify limits on what consumers may set. They are **NOT**
meant to describe the hardware capabilities. For example, I could have a
BUCK converter that supports 0-5V output voltage, but my circuit may
only allow working on the 2.7-3.3V range.
This patch reworks the API so that the API class layer manages this
information. This is done by drivers collecting all such fields in a
common configuration structure that is later accessed by the class
layer. This simplifies drivers implementation. For example, if A
consumer calls regulator_set_voltage() with a voltage that is supported
but not allowed, driver code won't be called. Similarly, if a regulator
is configured to be `always-on`, enable/disable driver code will never
be called.
Drivers have been adjusted. PCA9420 mode settings have been removed from
devicetree in this commit as they are not actual modes but PMIC states.
This will be refactored in a follow-up commit.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
