New ADC driver for the TI CC13xx/CC26xx family.
ADC channel configurations are translated from Zephyr constants to
simplelink driverlib ones (e.g., sample times use a lookup table).
Async mode was also implemented & tested.
Signed-off-by: Stancu Florin <niflostancu@gmail.com>
Adds Atmel SAMC20 and SAMC21 soc. C series is based on Cortex-M0+.
C21 contains CAN interface.
The init routines are same for SAMC20 and SAMC21. They use one
clock OSC48M without configuration.
The code is inspirated from atmel_sam0/samd21.
Signed-off-by: Kamil Serwus <kserwus@gmail.com>
This commit adds an optional property to the nRF21540 Front-End Module
devicetree description that specifies supply voltage in mV. This
property can be used by the nRF21540 driver to compensate the value of
achieved gain for different supply voltage.
Signed-off-by: Artur Hadasz <artur.hadasz@nordicsemi.no>
Signed-off-by: Jędrzej Ciupis <jedrzej.ciupis@nordicsemi.no>
Define the DMA and DMAMUX peripheral for the stm32MP1
DMA1 and 2 are of type V1 of 8 streams (channels) each
with a DMAMUX peripheral. See the RefManual for details.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add SparkFun Pro Micro header connector that is implemented by many
other controllers. This allows hardware with compatible headers to
define the related GPIOs and peripherals.
Signed-off-by: Peter Johanson <peter@peterjohanson.com>
Cavs25 alh definition is currently the same as in ace platform, which is
wrong, thus fix it.
Signed-off-by: Jaska Uimonen <jaska.uimonen@linux.intel.com>
Those dividers were configured in Kconfig so far. Add 'arm-podf',
'ahb-podf' and 'ipg-podf' "fixed-factor-clock" compatible DT child nodes
under 'ccm' (Clock Control Module) and use configured 'clock-div' values
instead of Kconfig equivalents.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
The ESP32 series MCUs allow to set a timeout which triggers an error
if the SCL line is unchanged for the specified amount of time.
By default, the ESP-IDF HAL sets the timeout to an arbitrary value of
10 times the bus cycle.
This is not sufficient for chips like the TI bq76952, which pulls the
SCL line low (clock stretching) for several 100 µs.
The timeout should also not be dependent on the chosen bitrate, as it
is defined by the time a chip needs for internal calculation before it
can provide requested data or continue communication.
This commit adds a property to devicetree to allow configuration of
the scl timeout. This value is set via direct register access, as the
ESP-IDF HAL does not provide access to the enable bit and does not
give any information about the maximum size of the timeout (defined
in I2C clock cycles in the register).
Fixes#51351
Signed-off-by: Martin Jäger <martin@libre.solar>
Microchip MEC172x has a modified eSPI SAF hardware implementation.
Hardware changes include multiple clock dividers for each SPI
flash device and data transfer using QMSPI local DMA.
espi reset interrupt is made a higer priority in MEC172x devicetree
because espi reset event resets all espi hardware and we don't
to want to service any other espi interrupt blocks when espi reset
occurs.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Set default interrupt priority to 3 for all Microchip MEC172x eSPI
host child devices except the UART's which are set to 1.
The espi peripherals don't require the maximum priority hence they
are being made uniform and a lower priority 3.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Microchip MEC172x QMSPI expanded its clock divider register
field from 8 to 16 bits. QMSPI source clock is on the fast
peripheral domain therefore get the frequency from the clock
control driver.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Add bindings to describe a block storage device based on flash map
partition.
Co-authored-by: Johann Fischer <johann.fischer@nordicsemi.no>
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Add devicetree binding for the PSA Crypto Random source.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
This commit adds missing binding file for the ite,it8xxx2-usbpd.
Without this file, the DT_HAS_*_ENABLED macro wasn't defined and
couldn't be used in the Kconfigs.
Signed-off-by: Michał Barnaś <mb@semihalf.com>
A USB TypeC connector has many peripherals associated with
it and the DTS binding in this commit provides a way to group
peripherals and properties in a device tree.
This binding is used with the USB-C Subsytem.
This is based on Linux, documentation:
https://www.kernel.org/doc/Documentation/devicetree/bindings/connector/usb-connector.yaml
Signed-off-by: Sam Hurst <sbh1187@gmail.com>
Add pin control properties to the STM32 UCPD bindings file so that
the pins can be configured in the device tree.
Signed-off-by: Sam Hurst <sbh1187@gmail.com>
Executing code out of RAM on IT8xxx2 requires that the relevant
addresses be mapped onto the CPU's instruction memory bus, referred to
by ITE documentation as Instruction Local Memory (ILM). ILM mappings
configure blocks of RAM to be used for accesses to chosen addresses when
performing instruction fetch, instead of the memory that would normally
be accessed at that address.
ILM must be used for some chip features (particularly Flash
self-programming, to execute from RAM while writing to Flash), and has
historically been configured in the Flash driver. The RAM for that was
hard-coded as a single 4k block in the linker script. Configuring ILM
in the flash driver is confusing because it is used by other SoC code as
well, currently in code that cannot depend on the Flash being functional
or in hand-selected functions that seem performance-critical.
This change moves ILM configuration to a new driver and dynamically
allocates RAM to ILM in the linker script, allowing software use of the
entire 64k RAM depending on configuration. This makes ILM configuration
more discoverable and makes it much easier to correctly support the
CODE_DATA_RELOCATION feature on this SoC.
Signed-off-by: Peter Marheine <pmarheine@chromium.org>
USB interface that may be used to send messages from a USB host to
the M4 processor in the S3B, and vice-versa.
Signed-off-by: Michal Sieron <msieron@antmicro.com>
Add support for regulator-boot-on to PMIC driver. Many PMIC devices will
be enabled at boot, so this property allows the regulator framework
to correctly track their state.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
As part of a previous refactor, this property was removed from the STM32
USART binding. The driver code to support this feature was not changed.
This commit simply adds the property back to the new base .yaml for
device trees which used it.
Tested on a proprietary board using the STM32U5 on USART1.
Signed-off-by: Peter Maxwell Warasila <madmaxwell@soundcomesout.com>
Migrates all Winsen sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all WE sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Vishay sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all TI sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all ST sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Silabs sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Sensirion sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Semtech sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Seeed sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all SBS sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Plantower sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Panasonic sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all NXP sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Nuvoton sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
