Upcoming memory protection features will be placing some additional
constraints on kernel objects:
- They need to reside in memory owned by the kernel and not the
application
- Certain kernel object validation schemes will require some run-time
initialization of all kernel objects before they can be used.
Per Ben these initializer macros were never intended to be public. It is
not forbidden to use them, but doing so requires care: the memory being
initialized must reside in kernel space, and extra runtime
initialization steps may need to be peformed before they are fully
usable as kernel objects. In particular, kernel subsystems or drivers
whose objects are already in kernel memory may still need to use these
macros if they define kernel objects as members of a larger data
structure.
It is intended that application developers instead use the
K_<object>_DEFINE macros, which will automatically put the object in the
right memory and add them to a section which can be iterated over at
boot to complete initiailization.
There was no K_WORK_DEFINE() macro for creating struct k_work objects,
this is now added.
k_poll_event and k_poll_signal are intended to be instatiated from
application memory and have not been changed.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The controller and host-side RX threads recently had their priorities
lowered to 8. Make the driver RX threads consistent with this.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Configure I2C using DT for the following STM32 boards:
disco_l475_iot1
nucleo_f401re
96b_carbon
olimexino_stm32
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
The SAM4S, SAM3X, SAME70 all use the uart_sam.c serial
driver. This patch puts the configuration in DTS and
out of Kconfig. The SAME70 uses the USART as well.
USART DTS support for the SAME70 is also in this patch.
Signed-off-by: Justin Watson <jwatson5@gmail.com>
The I2C Slave Read support isn't well defined and not actually supported
by any i2c driver at this point. We can add this back when slave mode
is more thought out.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add a STM32 LL based driver for the RNG processor. The RNG processor
is a random number generator, based on a continuous analog noise, that
provides a random 32-bit value to the host when read. The RNG passed
the FIPS PUB 140-2 (2001 October 10) tests with a success ratio of 99%.
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
Add support for KW40Z in the KW41Z IEEE 802.15.4 driver as both chips
expose almost the same radio registers.
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
The chip seems to require a wait time before reading packet
data after the RX sequence done interrupt, as imidiate reading
of it will indicate a packet size of zero and cause the RX
sequence done to be continually retriggered.
In addition, the extra clearing of the interrupt flags can be
removed, as this is already done at the beginning of the isr.
Jira: ZEP-2278
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
When building tests/kernel/test_build/test_debug on disco_l475_iot1 we
get the following build error:
drivers/i2c/i2c_ll_stm32_v2.c: In function ‘stm32_i2c_configure_timing’:
ext/hal/st/stm32cube/stm32l4xx/soc/stm32l4xx.h:207:38: error: ‘timing’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
#define WRITE_REG(REG, VAL) ((REG) = (VAL))
^
drivers/i2c/i2c_ll_stm32_v2.c:265:8: note: ‘timing’ was declared here
u32_t timing;
^~~~~~
Fix by initializing timing to 0.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Following implementation of LL based SPI driver,
add SPI support on nucleo_f334r8 board of STM32F3 series.
Change-Id: Ifbe39b1f2cecdd7db23be9c6943a914a155ebd77
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add SPI pin for the nucleo_f401re pinmux.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add a SPI master and slave driver for the L4, F4 and F3 STM32
SoCs families.
Change-Id: I1faf5c97f992c91eba852fd126e7d3b83158993d
Origin: Original
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Tested-by: Lee Jones <lee.jones@linaro.org>
As not all drivers support interrupts we don't have a means to know if
we can allow UART_INTERRUPT_DRIVEN to be enabled and thus various
Kconfig options that select UART_INTERRUPT_DRIVEN. Some drivers have a
interrupts, however not all do. So introduce a Kconfig option to let us
know what the driver actually supports.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In added mode flash operation are performed in timeslice
(in radio idle time).
Kconfig for mode enabling CONFIG_SOC_FLASH_NRF5_RADIO_SYNC.
Erase and write API implementations were rewritten and preserved against
concurrent execution.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add configuration, documentation, pinmux, fixup and dts support for
STM32F103x8 based Minimum System Development board.
Signed-off-by: Siddharth Chandrasekaran <siddharth@embedjournal.com>
as config SPI_CS_GPIO was selecting GPIO instead it
should just depend on it. This patch is a fix for
ZEP-2071 jira.
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
patch enables qmsi serial driver to pick baudrate and name
from device tree instead of Kconfig for UART0 and UART1
instance
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
The esp-idf package contains on the BSP a definition of the BIT macro
unconditionally #defined when rom/uart.h is #included. When Zephyr's
uart.h (which pulls in include/misc/util.h) that conditionally
This generates a compile warning on the re-definiton of BIT by the
esp-idf package.
Thus include uart.h after esp-idf's rom/uart.h to have BIT not
re-defined thanks to Zephyr's conditional definition.
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
This is a minimal driver enabling console output during the port
bringup. While the driver works, only one of the three UART devices
are supported, and there isn't any way to change any parameters or
use interrupts. This will most likely be superceded by a proper
driver after the port has matured.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Update driver to use DTS-generated #defines for port names,
and not obsolete Kconfig variables.
Signed-off-by: Geoffrey Le Gourriérec <geoffrey.legourrierec@smile.fr>
L4 write access requires 64 bits alignment
while L4 read access does not require any alignment.
To support specific check according to read/write,erase
a parameter is added to stm32_valid_range.
Signed-off-by: Michel Jaouen <michel.jaouen@st.com>
L4 have 64 bits write access.
The cast to 64 bits data address in write_dword
requires 3 right shifts on i (byte index) else the
data taken are wrong for i different from 0
Signed-off-by: Michel Jaouen <michel.jaouen@st.com>
We always have UART_IRQ_FLAGS set to 0, so just call IRQ_CONNECT with a
0 argument for the flags, and remove the UART_IRQ_FLAGS. This is
towards support for using the driver on the TI CC2650. (we add a
comment about that as well).
Signed-off-by: Geoffrey Le Gourriérec <geoffrey.legourrierec@smile.fr>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
