Following implementation of LL based SPI driver,
add SPI support on nucleo_f334r8 board of STM32F3 series.
Change-Id: Ifbe39b1f2cecdd7db23be9c6943a914a155ebd77
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add SPI pin for the nucleo_f401re pinmux.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add a SPI master and slave driver for the L4, F4 and F3 STM32
SoCs families.
Change-Id: I1faf5c97f992c91eba852fd126e7d3b83158993d
Origin: Original
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Tested-by: Lee Jones <lee.jones@linaro.org>
As not all drivers support interrupts we don't have a means to know if
we can allow UART_INTERRUPT_DRIVEN to be enabled and thus various
Kconfig options that select UART_INTERRUPT_DRIVEN. Some drivers have a
interrupts, however not all do. So introduce a Kconfig option to let us
know what the driver actually supports.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In added mode flash operation are performed in timeslice
(in radio idle time).
Kconfig for mode enabling CONFIG_SOC_FLASH_NRF5_RADIO_SYNC.
Erase and write API implementations were rewritten and preserved against
concurrent execution.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add configuration, documentation, pinmux, fixup and dts support for
STM32F103x8 based Minimum System Development board.
Signed-off-by: Siddharth Chandrasekaran <siddharth@embedjournal.com>
as config SPI_CS_GPIO was selecting GPIO instead it
should just depend on it. This patch is a fix for
ZEP-2071 jira.
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
patch enables qmsi serial driver to pick baudrate and name
from device tree instead of Kconfig for UART0 and UART1
instance
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
The esp-idf package contains on the BSP a definition of the BIT macro
unconditionally #defined when rom/uart.h is #included. When Zephyr's
uart.h (which pulls in include/misc/util.h) that conditionally
This generates a compile warning on the re-definiton of BIT by the
esp-idf package.
Thus include uart.h after esp-idf's rom/uart.h to have BIT not
re-defined thanks to Zephyr's conditional definition.
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
This is a minimal driver enabling console output during the port
bringup. While the driver works, only one of the three UART devices
are supported, and there isn't any way to change any parameters or
use interrupts. This will most likely be superceded by a proper
driver after the port has matured.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Update driver to use DTS-generated #defines for port names,
and not obsolete Kconfig variables.
Signed-off-by: Geoffrey Le Gourriérec <geoffrey.legourrierec@smile.fr>
L4 write access requires 64 bits alignment
while L4 read access does not require any alignment.
To support specific check according to read/write,erase
a parameter is added to stm32_valid_range.
Signed-off-by: Michel Jaouen <michel.jaouen@st.com>
L4 have 64 bits write access.
The cast to 64 bits data address in write_dword
requires 3 right shifts on i (byte index) else the
data taken are wrong for i different from 0
Signed-off-by: Michel Jaouen <michel.jaouen@st.com>
We always have UART_IRQ_FLAGS set to 0, so just call IRQ_CONNECT with a
0 argument for the flags, and remove the UART_IRQ_FLAGS. This is
towards support for using the driver on the TI CC2650. (we add a
comment about that as well).
Signed-off-by: Geoffrey Le Gourriérec <geoffrey.legourrierec@smile.fr>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit fixes the compilation error that occurs if both UART
ports on the FE310 SoC are enabled. The error occurs due to the
missing function definition of uart_fe310_irq_cfg_func_1 .
Signed-off-by: Jens Peter Schroer <jens@manetos.com>
Refactor internals of IPM driver removing bitfields and byte access of
32 bit registers.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
The current method of accessing 32-bit data and control registers does
not work for all quark architectures. Sometimes writing to those
registers byte-by-byte results in last byte occupying whole 32 bit
register.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Add necessary board files, pinmux and device tree in order to have a
usable debug console.
Origin: Original
Change-Id: I43a9d278c3f2c936a714263626722f630367b663
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Following migration of stm32f1xx series clock control driver to
STM32Cube LL API, cleanup stm32 code base in order to take into
account that this is the only clock driver available for stm32
family.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following introduction of stm32cube LL based clock control driver,
remove references to former native driver.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Before introduction of LL based clock control for stm32f1xx series,
prepare gpio driver to provide useful definition for new API
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
