Add PTC6 and PTA4 to the frdm_k64f pinmux table, and helper macros in
board.h to map them to SW2 and SW3 respectively.
Change-Id: Ia30df9015d6d3c09131b4fbb2f2009ee745f7268
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Statically compute the number of elements in the pinmux table rather
than keep a manual entry in step with the table.
Change-Id: I99634aa460a39bb8a9a10fe37d28aaae792aa641
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
MVIC does not have _REG_TIMER_CFG defined because it does
not have a timer config register. Add checks for MVIC at
places where it is used.
Jira: ZEP-1015
Change-Id: I59f5c43cc2d1b17cf9e88b940631c2542e9729ab
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Interrupt stubs now just push the ISR and parameter onto the stack
and jump to the common interrupt code, never to return.
Change-Id: I82543d8148b5c7dfe116c43f41791f852614bb28
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
In some cases we can either assume they are already masked
at boot and save some cycles, or the IOAPIC has configuration
from a prior boot stage that needs to be preserved.
Change-Id: I0c71ff0f01a6ee13a3b9c9e239d5a933d6cb6542
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This reverts commit 581e15ced2.
The commit was marked RFC and should not have been merged yet.
Change-Id: Iafd3587f8840e64670c32fa5726ea20ac9c9962a
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Provide a network driver wrapped around the KSDK ENET and PHY
drivers.
This driver is functional, just. It is not in a fit state to be merged to master yet.
Origin: Original
Change-Id: Id29e756f33c6c0263926139188c49f9a9c3d5e09
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Updated CONFIG_SOC_QUARK_SE_SS to CONFIG_SOC_QUARK_SE_C1000_SS
Change-Id: I7dc02d91a4d739f6cd3f84001d1dd29759317163
Signed-off-by: Javier B Perez <javier.b.perez.hernandez@intel.com>
No need to create new Kconfig that do exactly the same, just
reuse those from the main QMSI driver.
Change-Id: I965055f36845ac0464e4a383b0d05c3ae35c0015
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Update the power sample and drivers with the new device driver power
management API using the existing logic
Jira: ZEP-954
Change-Id: Idd94232e458767635973e94e9fc673c01612c1e2
Signed-off-by: Amir Kaplan <amir.kaplan@intel.com>
Removed CONFIG_INT_LATENCY_BENCHMARK dead code.
CONFIG_INT_LATENCY_BENCHMARK depends on ARCH="x86", it will never
be true for ARM code.
Change-Id: Ia5779a69b1bf670ebb140c2923c9fe0af6b781d4
Signed-off-by: Javier B Perez <javier.b.perez.hernandez@intel.com>
Removed unused workaround in loapic. There are no references
of usage.
Change-Id: I8700b4b7ce8efef5e7b95e6cdd2b201eae3f1f37
Signed-off-by: Javier B Perez <javier.b.perez.hernandez@intel.com>
During USB device reset, the controller must have its device address
cleared (set to 0). This is not really taken into account by most host
side stacks, which is the reason why this bug didn't show up before.
It was found when we were trying to run the USB20CV [1] compliance test
suite on Windows.
Without this fix the device doesn't show up on the targets list, which
means device enumeration failed. With this patch in place the bug is
fixed and the device gets listed.
Tested with the CDC ACM sample application.
Jira: ZEP-950
[1] http://www.usb.org/developers/tools/usb20_tools/
Change-Id: I0b78f7ce043fa29dde0fb7f3b3aecee9844f4d11
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
The driver originally gets the full-duplex configuration
from the PHCON1 register and PDPXMD bit as stated by the
ENC298J60 specification document section 2.6 "LED Configuration".
This section trust the board to LEDB connection to signal the
full-duplex configuration.
This commit gets the full-duplex configuration from Kconfig
symbols to allow a proper functionality even when the board
is not connecting LEDB apropriately.
Change-Id: I803958409a611e23e2c3e03f40b412f1695947af
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@intel.com>
There is a tx semaphore that controls a single access to the
transmission service. The device is capable to manage a single
transmission call at a time. Multiple requests need to wait
for the resource to be free.
This commit adds the initial release to the tx semaphore.
Jira: ZEP-895
Change-Id: Ic9879cfd15bb1494644b2cf0f4565f7e6a2c1c22
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@intel.com>
ENCC28J60 specs section 6.5 "MAC Initialization settings"
state that MACON3(7:5) register configure automatic padding and CRC.
It also states that the configuration 111 and 011 both configure as
all short frames to be zero padded with a valid CRC appended.
Nevertheless, experimentally, there are ocassions when configuring as 111
frames does not have a CRC appended. This frames could be rejected
by the receiver if it is configured to do so.
This commit changes configuration from 111 to 011, which is not
presenting that behavior.
Jira: ZEP-842
Change-Id: I302bb99f7a1f23b298fe0db0245963b640644040
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@intel.com>
As part of the effort to consolidate the BLE Controller's
HCI layer, the following files have been renamed:
* hci.h -> hci_internal.h: contains the HCI API to be used
by the driver
* main.c -> hci_driver.c: Implement bt_driver and includes
initialization and glue code
Jira: ZEP-726
Change-Id: Ica8b3e114da42a766a1b14ce59558cacd899a1a7
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Use the sys_ macros from byteorder.h to access all HCI
structure members that are endianness-dependent.
Jira: ZEP-726
Change-Id: I950f8eaca7048bf7972c2c4c347cfd5bbba17eb6
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Bug was introduced by a6cf6038e3
Change-Id: I91ceab2ca20c4d2f70a953b56d895152a471125a
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Provide a random driver wrapped around the KSDK RNGA driver.
Origin: Original
Change-Id: I43feeb37d8d5173c7b95af8e80434fb7dc77a83e
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
In 1.0 you could set only one callback on the whole gpio controller. It
was impossible for another sub-system to add another callback, without
overwritting an existing one.
Such API has been obsolete for a long time and no one is using it
anymore. Thus removing it entirely.
Change-Id: I6a17fd99373dc6cef1fa2ebb421e992412d5015e
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The LE_RAND HCI command was not filling in the rand array
with 8 random numbers as required by the spec.
Please note that the while() loop inside the command's
implementation can take up to hundreds of ms to execute.
Jira: ZEP-726
Change-Id: If27ff861ee5fa7842cd469e99d5bfa8ac47ac2fa
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Clean up, document and remove the macros used in hci.c
to access the different parameters and calculate lengths
of events and data structures.
Jira: ZEP-726
Change-Id: I476aa9e061dfe429b5181265167bffa203ed151b
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Switch to using the definitions in include/bluetooth/hci.h
for ACL data handling, both in RX and TX.
Jira: ZEP-726
Change-Id: I6b5f6de4ff568c4e73432df3edfa7d0a57f22fff
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Delete all event definitions from hci.c since the code now
uses the ones in include/bluetooth/hci.h exclusively.
This is the fourth and last commit in a series that transitions
from the event structures in hci.c to the ones in hci.h.
Jira: ZEP-726
Change-Id: I625c2aecf759823a1cc73a3ea096564284fe8c52
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Use Zephyr's include/bluetooth/hci.h for the HCI event
Number of Completed Packets.
This is the third commit in a series that transitions from
the event structures in hci.c to the ones in hci.h.
Jira: ZEP-726
Change-Id: I179bceb2f9dc07d7a1a524c3a80f0886f712ec2b
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Use Zephyr's include/bluetooth/hci.h for HCI event
handling in data-related events.
This is the second commit in a series that transitions from
the event structures in hci.c to the ones in hci.h.
Jira: ZEP-726
Change-Id: I0e9e6f709091859af47d90b26f5e7baa830a2838
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Use Zephyr's include/bluetooth/hci.h for HCI event
handling in control events.
This is the first commit in a series that transitions from
the event structures in hci.c to the ones in hci.h.
Jira: ZEP-726
Change-Id: I6f131675add18e2ae061f0fb2cf220ea7057f852
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This changes the way that aysnchronous events are handled
in the BLE controller's HCI layer. It performs all common
operations in a single place to avoid code repetition of the
same memory accesses over and over.
Jira: ZEP-726
Change-Id: Id9e8395944e8800f32dd9749da2b4f5c901c8682
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Continue using Zephyr's include/bluetooth/hci.h for HCI command
handling in more of the commands.
This commit deletes all command and command complete and
command status event definitions and structures present in
hci.c.
This is the sixth commit in a series that transitions from
the structures in hci.c to the ones in hci.h.
Jira: ZEP-726
Change-Id: I34635a1f55f3aef124fd5ff005c99cedb40b8a49
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Continue using Zephyr's include/bluetooth/hci.h for HCI command
handling in more of the commands.
This commit cleans up hci_cmd_handle() to use the new macros
added in previous commits.
This is the fifth commit in a series that transitions from
the structures in hci.c to the ones in hci.h.
Jira: ZEP-726
Change-Id: I152e02ed15042d367e95432bdd07ae5c74935be8
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Continue using Zephyr's include/bluetooth/hci.h for HCI command
handling in more of the commands.
This commit removes Nordic Semiconductor Vendor-Specific
commands, since they are currently unused and
manufacturer-specific.
This is the fourth commit in a series that transitions from
the structures in hci.c to the ones in hci.h.
Jira: ZEP-726
Change-Id: If0141072489777bfecc06e4aaa5f569898a5c449
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Continue using Zephyr's include/bluetooth/hci.h for HCI command
handling in more of the commands.
This commit ports the LE controller commands to hci.h.
This is the third commit in a series that transitions from
the structures in hci.c to the ones in hci.h.
Jira: ZEP-726
Change-Id: I3f11cca1da4aa6a20cce9706362818f8f6c87b0a
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
As part of closer integration into Zephyr, remove the use
of custom assert mechanism and use BT_ASSERT instead.
Jira: ZEP-761
Change-id: I27f37d697b0a84bc001754a8d0b4dbb6ddb54298
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Continue using Zephyr's include/bluetooth/hci.h for HCI command
handling in more of the commands, including the informational ones.
This is the second commit in a series that transitions from
the structures in hci.c to the ones in hci.h.
Jira: ZEP-726
Change-Id: Iecbc7ae5ba2c8435a51d62d59e8095aa25e6dc0e
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
They must provide the k_cycles_get_32() API and must not refer to
command packets: the latter do not exist on unified kernels.
Change-Id: Ia354dc060e5ad2595850f97da82d8feb590d16b7
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
This is a better choice of default; on Mint Valley using IRQ 0
for the timer collides with the DMA Error IRQ line.
Issue: ZEP-849
Change-Id: I14cb60fbe548488198813b2351e0ed1f07c2d07d
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Changed help message to be in compliance with the rest of sensors.
Change-Id: Ia18f7623eda5f86fe6f7d99ac934f1a9beda55a8
Signed-off-by: Javier B Perez <javier.b.perez.hernandez@intel.com>
This patch implements suspend/resume routines which
preserve SPI master 0 and 1 context in SYS_PM_DEEP_SLEEP.
The following parameters are suspended/resumed:
- All non-sticky RW registers for the SPI device which
are not related to a transfer.
- The SPI MASK registers (interrupt routing register).
The suspend/resume functionality is implemented in
the QMSI shim layer as a fast and temporary solution,
it will be removed and migrated to QMSI later.
Change-Id: Ib60317ca41013a3e794820e9c3ef34f35d108209
Signed-off-by: Dragan Cvetic <dragan.cvetic@intel.com>
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
CONFIG_PINMUX_DEV_QUARK_MCU is deprecated and QUARK MCU support
is replaced by CONFIG_PINMUX_DEV_QMSI. So delete this deprecated
CONFIG option.
Change-Id: I2cad6cfd4344386a00d45a579e8cc586935b041f
Signed-off-by: Qiu Peiyang <peiyangx.qiu@intel.com>
CONFIG_PINMUX_DEV_NAME should depends on CONFIG_PINMUX_DEV, not
CONFIG_PINMUX. In current situation, user will be able to access
pinmux dev driver without enabling CONFIG_PINMUX_DEV. This isn't
excepted to happen.
Change-Id: I75bcfff5a51e1dc93e002c0c6a65876f93cde5b8
Signed-off-by: Qiu Peiyang <peiyangx.qiu@intel.com>
In order to restore aonpt context after entering
SYS_PM_DEEP_SLEEP, suspend and resume functions
are called.
Only the interrupt mask is restored as it is reset by
the QMSI ROM and other registers are sticky.
The suspend/resume functionality is implemented in
the QMSI shim layer as a fast and temporary solution,
it will be removed and migrated to QMSI later.
Change-Id: I0dcd4552cd8c60ecb4eb650fc3ad85566b726a38
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
