Remove this code to clean up the driver.
Clock activation is done from device tree configuration in clock_control
driver.
Users are informed by warning about missing configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
On stm32wb, M0 core may enable and disable CLK48 when using RNG.
Lock related hsem to prevent M0 to disable CLK48 when it doesn't need it
anymore.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add kscan pins gpio driver for KSI[7:0], KSO[15:0] pins that
they can be configured to gpio mode. These pins registers address,
bit fields and function are different from GPIO group, so I create
a new compatible driver for these pins.
Signed-off-by: Ruibin Chang <Ruibin.Chang@ite.com.tw>
Add stub code for SDIO support, capable of verifying card responds to CMD5.
This commit also changes the architecture of the SDIO probe step to make
adding new protocol support more streamlined, and enable compiling out
support for undesired protocols.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Since nPM1100 may be configured statically in some circuits, BUCK node
may note be defined, so neither API ops or init call are used in the
code. Add __unused attribute to account for such case.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
While nPM1100 is to be operated in fixed configuration for some
applications, it has some degree of configuration via GPIOs. For
example, mode (auto/PWM) can be configured via MODE pin. VBUS current
can also be adjusted using ISET pin, even though there is no API yet to
limit the PMIC input current.
This patch adds a new regulator class driver for nPM1100 PMIC, so that
it can be used with the standard regulator API when needed.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
It is recommended that choices in Kconfig have names
so this commit adds missing one for the type of
host commands peripheral.
Signed-off-by: Michał Barnaś <mb@semihalf.com>
In some case, we may need to describe a domain clock for a device
while there is no way to configure it (ex: USB clock set on PLL_Q output
on F405 devices > It is not selectable).
Then, configuring a device clock domain in the clock_control driver
will allow to retrieve its subsys rate.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The dai.h interface does not prohibit calling dai_config_get()
with different direction values. The dmic driver should handle
invalid direction value explicitly and not rely on an assert.
Link: https://github.com/thesofproject/sof/issues/6896
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Periodic enqeueu of buffers can cause a attempt to start
a new transfer even though an endpoint is already busy.
Split usbfsotg_xfer_start() into two function, one to start
next transfer and another to continue the transfers, and use
busy state flags to explicitly mark an endpoint busy.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Pending state flag was only used by the UDC nRF USBD driver.
With the introduction of busy state flag it is no longer needed
and can be removed.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Periodic enqeueu of buffers can cause a attempt to start
a new transfer to host even though an IN endpoint is already busy.
Use busy state flags to explicitly mark an endpoint busy.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Provide a Kconfig option to enable HW RX and TX checksum, which
can increase throughput performances.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add missing "default y" to the Kconfig option so that it gets selected
automatically when a matching devicetree node is enabled.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
With ETH_STM32_HAL_API_V2 avoid log error message
if error log report:
we have problems if the traffic is high
Signed-off-by: Marc Desvaux <marc.desvaux-ext@st.com>
For NPCX SMB/I2C SMB modules in FIFO mode, the registers include:
* Common registers, offset 0x00-0x0f, accessible regardless of the value
of BNK_SEL
* Bank 0 registers, offset 0x10-0x1e, accessible if BNK_SEL is set to 0
* Bank 1 registers, offset 0x10-0x1e, accessible if BNK_SEL
is set to 1
In the current driver, it uses two structures, `smb_reg` and
`smb_fifo_reg`, to access `Common + Bank 0` and `Common + Bank 1`
registers. But It might be easy to misunderstand that they are two
different modules.
This CL tries to simplify this by the following steps:
1. Use `union` to combine `Bank 0/1` registers in the same structure.
2. Remove `smb_fifo_reg`. We needn't use two structures to present
SMB registers.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
The find_lsb_set is giving the position of the first '1' found,
starting from 1. "Bits are numbered starting at 1
from the least significant bit."
So that the find_lsb_set(64MBytes) is 27.
The HAL_QSPI_Init() accepts Init.FlashSize where "FlashSize+1
is effectively the number of address bits
required to address the flash memory."
To get 64MBytes = 2^26, the value of the Init.FlashSize must be 25.
and bit written to the DCR = 25.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The find_lsb_set is giving the position of the first '1' found,
starting from 1. "Bits are numbered starting at 1
from the least significant bit."
So that the find_lsb_set(64MBytes) is 27.
To get 64MBytes = 2^26, the value of the Init.DeviceSize must be 26.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Change the stm32_ospi_read_sfdp to have AddressSize
prepared in one single condition.
Add more debug msg.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This commit adds the support for host commands being transported
by the Serial Host Interface on the IT8xxx2 SoC.
Signed-off-by: Michał Barnaś <mb@semihalf.com>
This commit adds the support for host commands being transported
by the Serial Host Interface on the NPCX SoC.
Signed-off-by: Michał Barnaś <mb@semihalf.com>
Adds a driver for TDK InvenSense 42688 six axis IMU. Verified using
the sensor shell sample app via:
- sensor info
- sensor get icm42688p@0
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Signed-off-by: Yuval Peress <peress@google.com>
The stm32 devices shows a x2 factor on the LPTIM1,3,4
clock source but it acts as a prescaler.
The max lptim counter (timebase) is counting 4 sec
In that case, the LPTIM count unit is double.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
During flash operation, you have to disable XiP which force function
to be located in RAM. On top of that, the function `flash_put_cmd_addr`
is time critical so we need to declare as inline. For some reason,
sometimes the function was not really inline. Changed it to
ALWAYS_INLINE fixed the bug.
Signed-off-by: Mathis Raemy <mathis.raemy@gmail.com>
