Use PRIxPTR macros to fix compiler warnings of the form:
i2c_xilinx_axi.c:266:50: warning: format specifies type 'unsigned long'
but the argument has type 'mem_addr_t' (aka 'unsigned int') [-Wformat]
LOG_INF("Configuring %s at 0x%08lx", dev->name, config->base);
~~~~~ ^~~~~~~~~~~~
%08x
Signed-off-by: Kumar Gala <kumar.gala@intel.com>
Change init priority for SMBus from KERNEL_INIT_PRIORITY_DEVICE (50)
to KERNEL_INIT_PRIORITY_DEFAULT (40) since other devices which depend
on SMBus (like EEPROM) have the same priority.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
This commit adds the Gecko IADC driver and support for it to the
efr32bg_sltb010a board.
Signed-off-by: Mateusz Sierszulski <msierszulski@antmicro.com>
Signed-off-by: Roman Dobrodii <rdobrodii@antmicro.com>
- Add Gecko BURTC sys_clock driver to handle wake up from EM2,3 states
- Remove custom PM policy and dependency on HAL sl_power_manager service
- EM1 supported in all configurations
- EM2,3 supported only if SysTick is replaced by BURTC
Signed-off-by: Roman Dobrodii <rdobrodii@antmicro.com>
For the POSIX architecture, add options to:
* Clear the flash content at boot
* To delete the file on exit
* To just keep the flash in RAM instead of a file in disk
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This commit removes the unused argument form the `slz_bt_init` function,
and makes it consistent with what `SYS_INIT` expects - `int (*)(void)`.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
The fuel gauge tests should *not* have to enable CONFIG_SENSOR in order to
get access to the sbs gauge emulator.
Allow fuel_gauge sbs_gauge direct access to emul_sbs_gauge.c
Signed-off-by: Aaron Massey <aaronmassey@google.com>
All other watchdog drivers also use POST_KERNEL, and it seems on some
platforms where the TCO watchdog is used not all dependencies are yet set
up by the PRE_KERNEL_1 level.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This commit adds the SiLabs Bluetooth HCI driver. It also enables this
BLE HCI driver on the efr32bg_sltb010a board.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
When ASAN is used cmd_status is kept, but it cannot be linked
as the shell module is not present, this prevents ASAN
being used with the nrf52_bsim.
Fix it by conditionally compiling this code only if the shell is
being used.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
When using a dummy buffer on the RX side, do not
increment the destination memory buffer address.
This issue was uncovered when running the SPI
loopback test.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
The address increment logic was looking at both source
and destination parameters together. Separate them so
we can set one.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
HAL API changes in ethernet and pwm
SoC RT595 power management code change
west.yml update
Signed-off-by: Yves Vandervennet <yves.vandervennet@nxp.com>
The function dai_ssp_poll_for_register_delay() is meant to poll the
register until the value of the mask bits is equal to the "val"
argument or until poll timeout has occured. WAIT_FOR() returns the value
of the checked expression, so the check should be modified accordingly.
This should prevent the errors seen during every SSP trigger as below:
<err> dai_intel_ssp: dai_ssp_poll_for_register_delay poll timeout reg 487432 mask 4 val 4 us 125
<err> dai_intel_ssp: dai_ssp_poll_for_register_delay poll timeout reg 487496 mask 63 val 0 us 937
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Move semicolon from end of DT_INST_FOREACH to DEVICE_DT_INST_DEFINE
to make multi-instancing possible. This caused some problems with
CI after adding adc node to native_posix dts.
Signed-off-by: Benjamin Björnsson <benjamin.bjornsson@gmail.com>
The spi-sam0 driver does not initialize DMA parameters when the MCLK
peripheral is defined in the microcontroller header file. Fix it by
copying the initialization code from the non-MCLK case.
Signed-off-by: Brandon Del Bel <delbel@umn.edu>
- Add initial version of Infineon CAT1 i2c driver.
- Add initial version of binding file for Infineon
CAT1 I2C driver
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
Errata sheet of the stm32U5 (ES0499) recommends to avoid clearing
the DMAT bit with LL_USART_DisableDMAReq_TX to re-start
a DMA transfer on the UART Tx block. The function becomes empty.
This is also seen for stm32H5.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This adds the SPI driver for the Renesas SmartBond(tm) DA1469x MCU family.
The driver only supports controller mode. All four SPI modes are supported.
Note that the lowest supported speed is 2285714Hz.
Requesting speeds higher than 16MHz, will result in a 16MHz SCLK.
Co-authored-by: Stan Geitel <stan@geitel.nl>
Signed-off-by: Ben Lauret <ben.lauret.wm@renesas.com>
The delayblock is bypassed when the <dlyb-bypass> property is true.
DT_NODE_HAS_PROP tests whether the property is defined at all,
not whether a boolean property is true or false.
To get a boolean property’s truth value,
use DT_PROP(node_id, prop) instead.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Remove all init functions that do nothing, and provide a `NULL` to
*DEVICE*DEFINE* macros.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The below is the unit test result for the driver and kernel of
it82xx2_evb board.
GPIO/gpio_basic_api: PASS
I2C/i2c_api: PASS
Flash: PASS
UART/uart_basic_api: PASS
PWM/pwm_api: PASS
WDT/wdt_basic_api: PASS
KSCAN/kscan_api: PASS
kernel/sched/schedule_api: PASS
kernel/sched/preempt: PASS
kernel/timer/timer_api: PASS
kernel/sleep: PASS
ADC/adc_api: PASS.
ADC note: conversion time~=61.6us
sample time delay~=60us
wait voltage stable time~=202.8us
Set sampling time to 500us will pass for ADC test.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Add the pinctrl node that has been remapped in the chip of it82xx2.
And modify kscan's pinctrl for the it82xx2.
And swap I2C default pins.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
On iMX.RT devices, the number of GPIO pins exceeds the maximum of
64 that the PINT interrupt controller can support. Therefore, two
interrupt lines are now shared between the GPIO modules.
This patch allows the user to set the interrupt source for a GPIO
peripheral. For most LPC devices, this will always be the PINT. For some
RT devices, the PINT cannot use pins on GPIO modules other than 0 and 1
as input, and thus the INTA and INTB sources should be used.
Since Zephyr does not support sharing these interrupt between all GPIO
controllers, the user must configure a subset of all GPIO controllers to
use the shared module interrupts. An example of how to do so is provided
for the RT595 EVK.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Remove PINT management code from the LPC GPIO driver, as this code is
now contained within the PINT interrupt controller driver, which exposes
an interface to install interrupt callbacks.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Introduce PINT driver, for NXP pin interrupt and pattern match engine.
The driver currently supports only the pin interrupt feature of the
PINT.
Add DTS entires for the PINT on LPC and RT devices that support this
peripheral, and remove the interrupt defintions that are PINT specific
from the GPIO module on these devices.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The OFLEN bit has to be set by the host driver for ACE2.x. The
ownership of the IP is now handled at the host driver level, no longer
the firmware.
Setting it at the firmware level is a no-op if the bit is already set
by the host driver, and will fail it isn't already set.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
This patch fixes i2svss field initialisation in Device Tree for LNL
platform. It fixes this bug: #482
Problem is observed only when using SSP_BLOB_VER_1_5 version.
Unfortunatelly this version is not tested in FW validation tests.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
Clearing SPA bit together with OFFLEN bit causes FW hang.
This patch changes sequence to avoid that situation.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The upper ssp slot number should be retrieved from configuration
blob to support all possible settings. This patch fix this issue.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Repleace usage of shim2 device tree field with hdamlssp.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
In LNL platform GPDMA and ALH is no longer used. SSP uses LINK HDA
as a DMA engine. Therefore new shim, new register definitions and new
programming flows were defined.
This patch implements new SSP programming requirements for LNL.
Since HDA is shared between Host and DSP, link_config field was added to
dai_config structure. This one is provided by Host in new IPC4 fields
during interface configuration.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
Normally, the driver deactivates the QSPI peripheral for periods when
no QSPI operation is performed. This is done to avoid increased current
consumption when the peripheral is idle. For the same reason, the base
clock on nRF53 Series SoCs (HFCLK192M) is configured for those periods
with the default /4 divider that cannot be used otherwise. However,
when XIP accesses are used, the driver must be prevented from doing
both these things as that would make XIP to fail. Hence, a function
is provided so that applications can inform the driver that XIP is
needed and the above idle actions should be suppressed.
This function (`nrf_qspi_nor_xip_enable()`) replaces the old one
(`nrf_qspi_nor_base_clock_div_force()`) that was intended for similar
purpose but after deactivation of the peripheral was introduced in
commit 95d867e8ed it became useless.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Update the RTC driver menuconfig title to match the unified format
introduced in c41dd36de2.
Move the RTC driver menuconfig entry so the menuconfig list is still
(mostly) alphabetically sorted.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add a dependency on CONFIG_NET_L2_ETHERNET for
CONFIG_ETH_INIT_PRIORITY. This hides the Ethernet driver initialization
priority option in menuconfig unless CONFIG_NET_L2_ETHERNET is selected.
CONFIG_ETH_INIT_PRIORITY cannot currently be moved inside the
CONFIG_ETH_DRIVER if-statement in Kconfig as it is used outside the
Ethernet driver source files.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Introduce dedicated init priority for AT2X EEPROMs connected via
I2C or SPI to ensure they are initialized after I2C/SPI by default.
Signed-off-by: Martin Jäger <martin@libre.solar>
Add a driver to support the Xilinx AXI IIC Bus Interface logic core, as
described in Xilinx document PG090. This can be configured for use on
most Xilinx FPGA-based platforms such as the Digilent Arty.
Both the 2.00a and 2.1 versions of the core are supported. The 2.00a
revision has a bug causing dynamic read mode to not be reliable. With
this version of the core the driver falls back to reading only 1 byte
per interrupt.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
The get_status api allows to query whether clock is turned on or off.
Like the get_rate call, the status of gated clocks (for specific
peripherals), as well as domain clock sources(HSE, PCLK, PLL_P,..)
can be checked this way.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
