Add a sensor channel for the encoder counts. This is useful for
reading the encoder counts and calculating an absolute position
of a linear actuator.
Signed-off-by: Omeed Baboli <omeedbaboli@gmail.com>
If the TRNG has been unretained, it's not sufficient to enable
the clock, it must be fully reinitialized.
This is a minimal fix to ensure entropy is accumulated after sleep.
Long term, this driver should be made to use device power
management with power domain awareness.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
Fixes the auto channel status by using the channel number from fetched
wireless info, rather than the input config variable.
Signed-off-by: Muzaffar Ahmed <muzaffar.ahmed@silabs.com>
On M55M1 series, the clock module index is virtual to stay compatible
with 32-bit only cell value in devicetree. Its real value of being
64-bit integer needs to acquire indirectly.
Signed-off-by: Chun-Chieh Li <ccli8@nuvoton.com>
Fix invalid pointer-to-integer cast and comparison warnings in
ADXL362, ADXL367, and ADXL372 decoder drivers. The previous code
used `(uint8_t *)*fit` for offset comparison, which triggered
`-Wint-to-pointer-cast` warnings on recent compilers and could
lead to undefined behavior.
This patch replaces unsafe casts with `uintptr_t` arithmetic and
ensures type-safe offset calculations, preserving existing logic
while eliminating all build warnings.
Signed-off-by: Dilip Raman <dilipr@aerlync.com>
If `period_ms` is 3 or less `tmp` is 0. Since `tmp` is type `uint32`
subtracting 1 from 0 will wrap around to `UINT32_MAX` and is then clamped
to `UINT8_MAX`.
Fix the issue by changing `tmp` and `1` to signed types.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Add device tree node for MU instances that will be used by HSE and RTU
for s32z270.
Add support hash crypto for NXP S32 with Algo 2:
SHA224, SHA256, SHA384 and SHA512.
Add support cipher crypto with ECB, CBC and CTR mode by using ram key
catalog.
Add support 128/256 bits ram key length.
Signed-off-by: Ha Duong Quang <ha.duongquang@nxp.com>
The INA232 is another device in the INA2XX family and is very similar
to the already implemented INA230 and INA236. The main difference
between the INA232 and the INA236 is that the INA232 does not have a
Device ID register. Because of these similarities, it is implemented
in the ina230.x files in the same way as the IN236. Modifications to
the corresponding tests are included as well.
Signed-off-by: Johannes Meyer <johannes.meyer@intego.de>
auto negotiation might already be finished when we
check the link status, therefore check directly
instead of waiting 100 ms.
Signed-off-by: Fin Maaß <f.maass@vogl-electronic.com>
The latched bits are defined in the ethernet specification,
as the only latched bit, that we use, is the link status, improve
the code for it.
Signed-off-by: Fin Maaß <f.maass@vogl-electronic.com>
Starting with nrfx 4.0.0, the nrfx_err_t, NRFX_SUCCESS and NRFX_ERROR_*
have been deprecated. Most of them were removed here:
https://github.com/zephyrproject-rtos/zephyr/pull/99399
but a few were missed.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This commit prefixes "0x%x" debug logs with the entity, and prints the
"set" parameter when updating a filter.
Signed-off-by: Simon Piriou <spiriou31@gmail.com>
On the STM32MP2 series, the IPCC clock is managed at the system
level by the CPU responsible for system configuration.
In topologies where the Cortex-M33 acts as a companion processor, it
cannot enable the IPCC clock.
This update makes the IPCC clock optional in both the device tree
and the driver.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Create a shared base binding (ble-radio.yaml) for common Bluetooth LE
radio hardware capabilities to avoid duplication between vendors and
ensure consistent property naming across the ecosystem.
Properties are prefixed with 'ble-' and ordered chronologically by
Bluetooth Core Specification version (5.0, 5.1, 6.0). Each property
indicates a hardware capability, not current enablement state.
Signed-off-by: Ivan Pankratov <ivan.pankratov@silabs.com>
Removed conditional checks for device runtime put in DMA RX and
TX callbacks, ensuring that device runtime is always released
asynchronously.
Signed-off-by: Martin Hoff <martin.hoff@silabs.com>
This patch fix a reg write that needs to be done before calling the
callback. Since the user can start a new dma transfer in the callback,
it can miss the interrupt from the new transfer if the new transfer is
done before the interrupt bit is cleared.
Signed-off-by: Martin Hoff <martin.hoff@silabs.com>
Removed unnecessary power management state lock calls since the DMA is
on a power domain that already handles state locking.
It will now managed directly pm_device which will active power_domain
and then block pm_state.
Signed-off-by: Martin Hoff <martin.hoff@silabs.com>
Added calls to pm_device_runtime_put() to ensure proper device runtime
management when configuration or DMA transceive operations fail.
Signed-off-by: Martin Hoff <martin.hoff@silabs.com>
This patch is needed to block the pm_state "PM_STATE_SUSPEND_TO_IDLE"
when a device on the power domain (actually all the peripherals) is
active. Without this patch, cpu can decide to go to deep sleep while
a peripheral is active.
Signed-off-by: Martin Hoff <martin.hoff@silabs.com>
Most drivers for Series 2 depend on clock control, but didn't
declare it. Enable clock control by default for Series 2 SoCs.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
The watchdog timer on SiWx91x devices is designed to
pause during deep-sleep and resume after wakeup.
However, an incorrect check in`wdt_setup` was
preventing this intended behavior. This patch removes
the check, restoring the correct pause-in-sleep
functionality.
Signed-off-by: Sai Santhosh Malae <Santhosh.Malae@silabs.com>
NuMaker watchdog control register is write-once after power-on
or reset. Thus, the control registeris written in the setup
function and the disable function only disables IRQ.
Signed-off-by: cyliang tw <cyliang@nuvoton.com>
Added PTP timestamping support in NETC ENETC host driver for no-tag
supported NETC switch.
On RX path, extended descriptor is used on host (pseudo MAC) to get
timestamp writeback.
On TX path, TX timestamp response should be enabled on host (pseudo MAC).
After TX, writeback TX timestamp ID should be updated to tx pkt fifo.
Once RX path received TX timestamp response, match TX timestamp to tx
pkt in fifo with the timestamp ID.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
For NETC switch with tag support, PTP timestamping had already been
supported in tag driver.
This patch is to add PTP timestamping support for no-tag supported switch.
Timestamp functions are implemented and exported for host driver to
handle.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Converted to use NETC_PTP_TIMESTAMPING_SUPPORT for PTP timestamping.
PTP timestamping is needed only when NET_L2_PTP and PTP_CLOCK_NXP_NETC
are selected.
Used default 16 bytes for ETH_NXP_IMX_RX_RING_LEN for PTP timestamping
because RX extended descriptor would be used.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
PTP timestamping should be enabled only when NET_L2_PTP and
PTP_CLOCK_NXP_NETC are selected. And NET_PKT_CONTROL_BLOCK
is required for PTP timestamping code.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Add a conditional compile around data in `cdns_i3c_irq_handler` to
prevent a warning when building controller only and without ibi.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
Extends the devicetree library test to exercise the hwspinlock dt spec
macros and detect the context initializer build warning that was fixed
in commit 8b208b0d5a. Previously the build
warning wasn't reproducible in-tree.
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
There can be a race conditon where another interrupt fires while it
is in the callback, but then the interrupt is cleared towards the
end of the interrupt. Clear the interrupts it intends to service
at the beginning of the ISR.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
Add a new function to free an mbedtls_shim session:
'mbedtls_free_session()'. Together with 'mbedtls_get_unused_session()',
these will be the only entry points to acquire/release sessions.
In this way it's easier to ensure that the mutex is properly held while
setting the 'in_use' parameter.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
Move mbedtls_get_unused_session_index() at the top of the file and leave
cipher and hash functions below.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
Use net_buf_tail() instead of __buf for proper buffer positioning.
Add null check and error handling for nocache buffer allocation.
Only copy data for OUT transfers during buffer setup.
Signed-off-by: Mark Wang <yichang.wang@nxp.com>
