To allow transition to device tree based clock configuration on
stm32 targets, rework clock_control driver to use intermediate
STM32_ macros initially defined as the equivalent Kconfig macros
for now.
Propagate the change in all code using these macros.
The reason to introduce these new macros instead of configuring
Kconfig flags using dt kconfigfunctions is that we'll need
to be able to inform users that Kconfig flags are deprecated
once the whole family conversion is done, to encourage
out of tree users to adopt this new configuration scheme.
Note: For now STM32H7 series and code is excluded.
This is the same for some series specific code such as
PLL mul/div for L0/L1 and XTRE prescaler on F1 series.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
NPCX PWM supports output buffet select to push-pull or open-drain. Add
output buffer select option 'drive-open-drain' in devicetree for NPCX
PWM. If set, the PWM output will be configured as open-drain. If not
set, defaults to push-pull.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Signed-off-by: Wealian Liao <WHLIAO@nuvoton.com>
The definition to check if timers have up to 6 channels was causing
warnings when -Wexpansion-to-defined was enabled.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Convert from device_get_binding to DEVICE_DT_GET. In doing this we
no longer need the label in the devicetree node so we remove that.
Removed all __ASSERT_NO_MSG(clk) since we'll get a build error if
DEVICE_DT_GET cant be satisfied, and the clock control api's will
handle reporting if the device_is_ready.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update NPCX PWM driver so PWM can be turned off as the first call when
PWM_POLARITY_INVERTED is used.
Signed-off-by: Keith Short <keithshort@google.com>
Remove DW and PCA9685 PWM controller drivers as they are unmaintained
and broken.
Both drivers lack support for the pwm_get_cycles_per_sec_t API function
which was introduced in commit 56e0b53c6e
in 2016.
Fixes#18607, #18608
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Disable RTC WDT enabled (by default) by 2nd stage bootloader in ESP-IDF.
This WDT timer ensures correct hand-over and startup sequence from
bootloader to application.
Enabling bootloader caused system clock initialization to fail
when clock rate is greater then 80MHz. This also fixes
esp32 clock source code.
Signed-off-by: Mahavir Jain <mahavir@espressif.com>
Extend the PWM API with optional API functions for capturing PWM pulse
width and period cycles.
Fixes#26026.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Convert driver(s) to DEVICE_DEFINE instead of DEVICE_AND_API_INIT
so we can deprecate DEVICE_AND_API_INIT in the future.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The STM32L0 series MCUs have quite basic timer features only, so we
remove some unavailable configuration options. They were properly
initilized by the LL StructInit functions for other MCUs anyway.
Signed-off-by: Martin Jäger <martin@libre.solar>
So far nRF's TIMER was used for generating PWM signal. Add support for
generating PWM based on RTC, which is sourced by 32KHz low frequency
crystal. This allows to use low frequency PWM with much lower power
consumption, because high frequency clock path can be disabled.
Don't support RTC clock prescaler, because maximum 512s period covers
most use cases. This allows to adjust pulse and period cycles to the
fact that CLEAR task event is generated always one LFCLK cycle after
period COMPARE value is reached.
Also update hal_nordic revision, as it contains updated check for PPI
channels conflict when RTC is used to generate PWM.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
So far 'timer-instance' DT property was the way to configure TIMER which
was used for generating PWM signal. Replace that by using 'generator'
phandle, so we get prepared for supporting RTC instances as PWM signal
generator.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
There is some kind of runtime clock scaling implemented when period
cycles exceed 16-bit value. This is broken, because configured PWM has
far higher frequency in that case. Replace that mechanism with simply
veryfying if requested PWM period does not exceed 16-bit value.
Suggested-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Use Nordic HAL to configure GPIO output. This adds support for P1 GPIOs,
when pin numbers above 31 are used.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Convert pwm drivers to use new DT variants of the DEVICE APIs.
DEVICE_AND_API_INIT -> DEVICE_DT_DEFINE
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
- Remove SYS_ prefix
- shorten POWER_MANAGEMENT to just PM
- DEVICE_POWER_MANAGEMENT -> PM_DEVICE
and use PM_ as the prefix for all PM related Kconfigs
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This CL replaces all DT_ prefix with NPCX_DT_ for all macros used
for providing npcx device information in soc_dt.h It avoided the
ambiguity with the DT_ prefix for system DT macros/defines.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Enable ARR preload so that period or pulse updates are taken
into account synchronously with update event
(at the end of a ongoing period)
And thus avoid undetermined intermediate pulse.
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
The parameters of the associated PWM timer were not being picked up
properly, as it was assumed that parent index is the same as the child
index. This is not necessarily true if other timer nodes are active and
not being used for PWM.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Set stm32_dt_pinctrl_configure function as the unique entry point
to STM32 DT pinctrl management.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move pinctrl remap functions out of stm32f1 definition in order
to get it available to all series.
Allows use of more IS_ENABLED macros in calling drivers and make
code more readable.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to be in line with other DT_INST macros in zephyr code base,
swap the arguments order in following macro definitions:
*ST_STM32_DT_PINCTRL
*ST_STM32_DT_INST_PINCTRL
Update the users accordingly.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Current set of helpers provided for STM32 pinctrl devicetree are
using device instance as input.
In order to prepare for next version that will take node identifier
as input, change existing set of macros using _INST_ namespace.
Additionally rename NODE_ID_FROM_PINCTRL to
ST_STM32_DT_INST_NODE_ID_FROM_PINCTRL.
Finally update existing macros users to this new name scheme.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Now that Zephyr names have been made short and nice the need of these
helpers is less justified.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
In npcx7 series, there're 8 Pulse Width Modulator (PWM) modules and each
one support generating a single 16-bit PWM output. A 16-bit clock
prescaler (PRSCn) and a 16-bit counter (CTRn) determine the cycle time,
the minimal possible pulse width, and the duty-cycle steps.
Beside introducing pwm driver for Nuvoton NPCX series, this CL also
includes:
1. Add PWM device tree declarations.
2. Zephyr PWM api implementation.
3. Add aliases in npcx7m6fb_evb board device tree file for supporting
samples/basic/blinky_pwm application and pwm test suites
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
Replace all calls to the assert macro that comes from libc by calls to
__ASSERT_NO_MSG(). This is usefull as the former might be different
depending on the libc used and the later can be customized to reduce
flash footprint.
Signed-off-by: Xavier Chapron <xavier.chapron@stimio.fr>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
