With this code we can successfully boot and context switch into
the main thread. Nanokernel hello_world has the expected
"Hello World!" string in the RAM console.
Change-Id: I56335d992f5a7cbb12d9e4c02d1cc23ea28ae6ef
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
If XIP is turned on, only hardware breakpoints may be used, and
code cannot be loaded onto the device with nios2-download
or GDB 'load' command. RAM-constrained applications are free to
enable this if they need to.
Change-Id: Iee2d41f71f7ca2bc599801cf3cf0fac680273e51
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
When an image is sent over the wire with the GDB 'load' command,
it tries to start execution from the __start symbol, which needs to
be in RAM. Since the reset vector is in ROM, name it something else.
Change-Id: Id0bbfa76db9a8a81bd7ff20be3f2baec81eae15e
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Kconfig doesn't enforce any kind of alignment when specifying the
ISR stack size. Perform the assembly equivalent of STACK_ROUND_DOWN.
Change-Id: Ib7fb72ff7db8a3aa20ec6d0c59a03aa8227f6671
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
CONFIG_INIT_STACKS should initialize all stack regions
with 0xaa. Make sure the initial interrupt stack gets this
as well. Take care not to exceed the bounds of the array
if it is not 4-byte aligned.
Change-Id: Ib23329ac84a5a8515272be2944f948e8faba65b3
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This core has extra debugging features useful for this bring-up
exercise.
Change-Id: I619bc8768acb1d9be8699a6e238168f47e605f3d
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Add hidden configuration HAS_KSDK for SoCs to select if they have
support in the ksdk.
Change-Id: Ia4cd11901bc26d21a3bdfad6236d66656bb292cb
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Use a kbuild trick to force built-in.o to get built even if there isn't
any code so we can link properly. This is cleaner than keeping around
empty files that don't do anything.
Change-Id: I4214d21104fe5f49613fa5697c8116b0e8c8aa50
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
There was a reference to SOC_FAMILY_NRF5 which was not use by anyone
else and it seemes like it was a typo, where the right reference was
to symbol SOC_NRF5. However, the right fix is to move both sites to
use SOC_FAMILY_NRF5 *and* fix the SOC_SERIES to be only nrf52,
otherwise it causes path duplication and the build fails.
This was also causing documentation warnings that are thus killed.
Change-Id: I92e74a6158f02df43e6e857df8f1e67bcfdd9551
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Change the LOAPIC timer IRQ number to 10. It should not
be 0.
Change-Id: I156286d0e3b903cca07cc3f87804b145aacaf117
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
The ReST parser dislikes enumerations with no empty lines in
between. Whatever.
Change-Id: I480c08fe5b69f0d0f3ebfacdc64fc9e3ec94da21
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
No code uses it and it being undefined anywhere generates a
documentation warning.
Change-Id: I09de2e58edf82e7fb9780a5dea98a282502436b6
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
The KSDK device header files require a preprocessor macro that defines
the part number string (e.g., MK64FN1M0VMD12). Create a hidden Kconfig
option to hold the part number string, and hidden Kconfig options that
the board Kconfig will use to select the specific part number.
Change-Id: I612e785026261e425b47b5b7fae0c65b4f94b30b
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get these out of system.h instead. A clause in libc-hooks.c
for newlib added since we don't get RAM size from
CONFIG_SRAM_BASE_ADDRESS.
Change-Id: Ic35113395b951f625e8e29658afe19c525037964
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
We will require 6 variables to be defined by SOC-specific
linker script; these values in turn can be pulled from
defines in layout.h.
To help position code correctly we define two new ELF sections
for this arch, 'reset' and 'exceptions'.
Change-Id: Idffbd53895945b7d0ec0aac281e5bf7c85b4b2c2
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Nios II does not have a power saving instruction, so there is nothing
to really do here other than ensure that interrupts are in the correct
state when leaving nano_cpu_atomic_idle().
Change-Id: I664c7542dc2fc1795a453d35e183a737dcb20c38
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
For the moment, NIOS2_CPU_SOF must be set with the path to the
CPU configuration. We are checking with Altera on whether we
can directly check in the binary to the source tree.
These scripts depend on tools provided by the Altera Quartus
Prime Lite Edition. This is available for free but requires
registration on Altera's website to obtain.
Change-Id: Ia6cb6c9e43c3e141807a887cb25c47b370a7d8e9
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Altera tools for creating .pof files for flashing onto their
FPGAs require UFM data to be in this special format. Extend
the current 'all' and 'zephyr' targets to additionally create
this .hex file using objcopy, with the same exclusions as the
existing rule for .bin files.
Change-Id: I75293fba47536545359f817a1f2c1ae905b9d25c
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
__start is the CPU's reset vector. In a typical Nios II configuration,
the exception vector is 0x20 bytes after the reset vector, severely
constraining the amount of code that can go in here.
Split this into __start and __text_start. The only thing that __start
really need to do is init the instruction cache and jump into
__text_start.
JIRA IDs placed in comments for missing items.
Change-Id: I3c6b8ed65e8fcf6b6a735b80cf007d0180599230
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Linker scripts for Nios II will also need these headers as it
specifies the device's physical layout and various important
vector addresses.
Change-Id: Ie9efaf19e53d2493eed7b9783052393d7ea9dd0f
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Include nrf.h instead of directly using the specific header
required. This will be useful in the future when additional
Nordic ICs are supported.
JIRA: ZEP-377
Change-Id: I7a7257b0aaa5fa0a0d202322c366efbdd1d84458
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Translate CONFIG_SOC_SERIES_NRF52X to NRF52, which is the macro
expected by the Nordic MDK headers.
JIRA: ZEP-377
Change-Id: Ic846e4cddf8146ae9d96bc98d4b12311552dc4f6
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
There are a few problems with the code being repaired here.
1. A seti was used to re-enable all interrupts, even though the
thread being switched to may have had certain interrupt priorities masked.
2. saved status32 already has SC bit if thats wanted, so its ok to just
restore status32 as-is w/o needing to and off anything.
3. the code is difficult to write using kflag and seti because as you
restore registers, there aren't any to use. But we can exploit a
trick where we pretend an interrupt has occured by setting a bit in
AUX_IRQ_ACT, and then use RTIE instruction to restore status32
atomically with branching to return address. Something about the way
this code was written was causing stack corruptings and crashes in an
application that uses a high rate of both FIRQ and Regular interrupts.
Change-Id: Ia7166d51f0e750c07832ab115b7151ce37ee0278
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Since firq utilizes a 2nd register bank, and since all of those
many GPRs can be used, the strategy here is to save extra registers,
such as lp_count, lp_start, lp_end into callee saved registers.
These registers are safe to use because the C-ABI followed by the
compiler will cause these to be spilled to the stack if a C function
wants to use them. By selecting upper GPRs, r23-r25, it is very unlikely
the compiler will spill them. This improvement, therefore, can avoid a
d-cache miss since we are avoding memory altogether when saving these.
The struct firq_regs is no longer needed.
Change-Id: I7c0d061908a90376da7a0101b62e804647a20443
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Generate kernel image in Intel Hex format when building for the nRF52.
Remove the additional step from the board doc file.
Change-Id: I619496f64037c2a0ac459ae05e549e01458e0f71
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
It was found that the test latency_measure, when compiled
for microkernel, would fail on the ARC. This because the
trap handler, used by irq_offload, wasn't supporting thread switching.
This submission adds the code to do that, and the code size is
bigger only when CONFIG_MICROKERNEL is defined.
To keep code a bit smaller, there is a trick exploited here where
the AE bit is cleared in the STATUS32 register and in AUX_IRQ_ACT,
bit 1 is set, to make it appear as if the machine has interrupted
at priority 1 level. It then can jump into some common interrupt
exit code for regular interrupts and perform an RTIE instruction
to switch into the new thread.
test/latency_measure/microkernel now passes.
Change-Id: I1872a80bb09a259814540567f51721203201679a
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Moved setting of specific Cortex-M compiler flags in each SoC directory
unify setting them in the arch/arm/soc Makefile.
Add flags for Cortex M0, M0+, M1, M3, M4, and M7. However only
CONFIG_CPU_CORTEX_M3 and CONFIG_CPU_CORTEX_M4 are supported at this time
As part of this change converted Kbuild files for some SoCs into
Makefiles as the Makefiles would be empty otherwise.
Change-Id: Ie4e0178b141ca761ec482a610ae50e94fe58070f
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Introduce a soc-cflags, soc-cxxflags, and soc-aflags as a means for
SoC specific compiler flags to be set without manipulating Kbuild
options directly.
Change-Id: I2c8f5019fb237429e59717ef96bd4251a61dc1a5
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
For some security scenarios the GDT may already be setup and locked,
in which case the kernel trying to set it again could lead to problems.
Change-Id: I727c1d213479f46a4bb6f0c04a9096131e10b3e7
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The .nd on a branch is WRONG if its an unconditional branch. Not needed.
On conditional branches its a compiler feature that is not yet functional
with ARC targets. Typical code for this compiler can use .d to put
something in the delay slot of an instruction, but using .nd is probably
never wanted.
Change-Id: If1017c468e6e7af269ea73daeb4bc223dcc0059f
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Microkernel on ARC works fine, was missing some declarations in the
linker file.
Also enable testing of microkernel with ARC and disable tests where
ARC is not supported yet.
Jira: ZEP-396
Change-Id: I2ac7b8dc0bea22f5d2e24832d9e3afad8df9f580
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Convert leading whitespace into tabs in Kconfig files. Also replaced
double spaces between config and <prompt>.
Change-Id: I341c718ecf4143529b477c239bbde88e18f37062
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add missing Kconfig files and connections to expose Kconfig options
in ext/ directories. Fixup QMSI to only be exposed on platforms that
utilize it.
Change-Id: I6c6c5011b2bf2966f65aa8279dc594a244821956
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The ARC CPU comes up from reset with i-cache enabled.
It can have garbage in it from a previous run.
The fix is to check the build register for the i-cache, and if its
present, invalidate it fully, and then disable it.
_icache_setup() is called later to turn it on.
Change-Id: I26fae915153841c61e9530d5af2ddb9d0553275b
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
EM11D is a ARC CPU configuration that can be selected for the
ARC EM Starter Kit. The board support for this board will be
submitted separately to expidite review.
Change-Id: Ifc4d48e1f5e01d44d1706e6426bd3b2d77ebe2f8
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
EM9D is a ARC CPU configuration that can be selected for the
ARC EM Starter Kit. The board support for this board will be
submitted separately to expidite review.
Change-Id: I2c85bdab6ea7bfb257e94e4c72b11b4568dbac19
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Move away from native driver and use the UART driver provided
by QMSI.
All peripherals on Quark MCUs will use QMSI drivers developed
specifically for Quark and optimized for this MCU line.
Change-Id: If4e27f38736849ea3e12c269886e2a03d957b671
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Now that we have QMSI sensor subsystem drivers, lets use them.
Change-Id: Icd301b6c044280b5b25d719b6dcc16d556a2ea8d
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Now that we have QMSI sensor subsystem drivers, lets use them.
Change-Id: I1340ba8930fc8676f7b706540a105250ce3e51b9
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Now that we have QMSI sensor subsystem drivers, lets use them.
Change-Id: I1776178ad6fb984d6e293dbfa8bb1d718e4c2566
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
My boss is asking me to add "all rights reserved" to synopsys banners.
Change-Id: Id74bf3cd0be6bc3159a8b687a37eb11fa3a49f3e
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
