So far, DT did not support the flash driver name.
Any flash-controller should have the appropriate
flash driver that should be identified by its name.
This path adds generic support for extract the description
from the flash-controller node,
adds implementation of this property for all nrf5x targets.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Where missing add compatible = "soc-nv-flash". Also added a label for
all the soc-nv-flash that we might use in the future.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Similar addition was don previous for nRF52840.
Added flash-controller description and moved flash description to
it. Added property for description of
the flash alignment required by write operations.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Similar addition was don previous for nRF52840.
Added flash-controller description and moved flash description to
it. Added property for description of
the flash alignment required by write operations.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Added flash-controller description and moved flash description to
it (for coherence). Added property for description of
the flash alignment required by write operations.
Thanks to that l-value FLASH_WRITE_BLOCK_SIZE macro
will be generated. It is useful for any component uses
the flash.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Remove memory node from skeleton dtsi and add device_type
property in every memory node in soc dtsi files
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
This patch add the unit-address component to memory and flash
nodes. According to the DT specification, the unit-address of
a node must match the first address specified in the reg
property of the node.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
This patch adds #address-cell, #size-cell properties to
cpus container node and device_type, reg properties to
cpu node.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Now that we can utilize label in the device tree we can convert to
getting the device name for the NRF UART out of the device tree
instead of from Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add device tree support for nRF51822 SoCs and Arduino 101-BLE,
Curie-BLE, BLE Nano, PCA10028-DK, and Quark-SE BLE boards. This
is minimal support for memory, flash, and UART.
Change-Id: I7e572bea537e384b6d66e520462f023ace0c9b35
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add device tree support for nRF52840 SoC and PCA10056-DK board. This
is minimal support for memory, flash, and UART.
For the nRF52840 we select between "nordic,nrf-uarte", "nordic,nrf-uart"
support for each board.
Change-Id: I1c377e0cb97ff4716ea5489fffaa7c0e2b34d18a
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add plumbing to build system and SoC level dtsi for the NRF52832 SoC.
We additionally add the necessary yaml files for the UART on the NRF52
SoCs.
Change-Id: I3b4a821b2993827e33d8e84bdbbc759d1521f8bd
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
