In the recent MDK brought by nrfx 1.6.2, these legacy peripherals have
been revealed as available also in nRF52810. This patch allows their
use in Zephyr drivers.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Actually, add the "status" property that enables the nodes explicitly.
They were apparently enabled by default without this property.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Use the symbol generated from DT so that it is common for nRF9160
and nRF5 family SoCs. To avoid artificial renaming of CLOCK_POWER_IRQn
to POWER_CLOCK_IRQn.
For nRF5 family SoCs clock nodes were not defined so far, thus they are
added so that the proper DT symbol is generated for them as well.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add missing node for instance 0 of the RTC peripheral and use an alias
to the flash-controller node instead of the nvmc node definition (there
is no need to have a separate node just to get the NVMC base address).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This commit introduces the main device tree header files (.dtsi)
for Nordic nRF9160 SOC, for both Secure and Non-Secure domains.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
We only need to add the reg property in flash0 and sram0,
in the different DTS headers for the nRF SOCS. We do not
seem to need to define the nodes again. This commit applies
this simplification for flash and sram sizes definition.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Fix the following warning that shows up in some NRF device tree files:
Warning (simple_bus_reg): /soc/pwm@4002D000: simple-bus unit
address format error, expected "4002d000"
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix the following warning that shows up in some NRF device tree files:
Warning (simple_bus_reg): /soc/pwm@4001C000: simple-bus unit
address format error, expected "4001c000"
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
1. PWM device node added with alias to all
nRF52x DTSI files. 1 instance for
nRF52810, 3 instances for nRF52832, and
4 instance for nRF52840.
2. Added yaml binding for Nordic PWM node.
Signed-off-by: Gaute Gamnes <gaute.gamnes@nordicsemi.no>
Adds the virtualcom device to the nrf52840 SoC dts and adds a board
specific nrf52840_overlay.dts file, copied exactly from the
arduino101_overlay.dts file, to set the console device name
appropriately for the subsys/usb/console sample project.
There were no clear alternatives to add a usb_cdc: virtualcom device to
all known SoC devices with USB support as should probably happen.
There was also no clear alternatives to add a non-board specific overlay
to the example.
This fixes a specific problem with the nrf52840-dk board for this sample
project.
Signed-off-by: Tom Burdick <thomas.burdick@gmail.com>
Newer DTC now warns about mismatch between the reg and unit-address.
Most of these cases are due to case not matching, so fix thoses so
everything is lowercase.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Commit introduces support for ARM TrustZone CryptoCell 310
for Nordic Semiconductor nRF SoCs in device tree.
Signed-off-by: Dominik Kilian <Dominik.Kilian@nordicsemi.no>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. This lets us
remove:
CONFIG_SOC_NRF51822_QFAA
CONFIG_SOC_NRF51822_QFAB
CONFIG_SOC_NRF51822_QFAC
CONFIG_SOC_NRF52810_QFAA
CONFIG_SOC_NRF52832_QFAA
CONFIG_SOC_NRF52832_CIAA
CONFIG_SOC_NRF52832_QFAB
CONFIG_SOC_NRF52840_QIAA
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that we have a common DT_SIZE_K macro use it instead of defining
__SIZE_K eveywhere. We also have DT_SIZE_M, so use that in a few
places as well.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The LEDs, buttons and necessary aliases are now configured via dts.
This commit breaks the sample under samples/boards/nrf52/power_mgr.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
This change adds DTS definition of SPI device for nRF chips.
It also removes SPI pin configuration from Kconfig and moves it to
chip DTS.
Signed-off-by: Filip Kubicz <filip.kubicz@nordicsemi.no>
This commit adds ADC nodes to DTS files for nRF SoCs and introduces
corresponding bindings for these nodes.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The nvs sample assumed a 1 KB flash erase block size, which caused the
sample to fail on frdm_k64f because its erase block size is 4 KB. Get
the erase block size from dts instead.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This commit adds support for the nrf52840_pca10059 board.
The flash partitions are configured to allow migrating from
the stock bootloader to MCUBoot.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Since the UART0 @ 0x40002000 can either be UART or UARTE the user of the
soc.dtsi needs to select either compatible = "nordic,nrf-uarte" or
"nordic,nrf-uart"
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit moves the definitions for the LED and Buttons
supported in nrf52810_pca10040 DK in DTS from board.h. Aliases
are kept in board.h to make basic examples pass.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
The nRF52810 is a low-cost variant of the nRF52832, with a reduced set
of peripherals and memory. This commit adds basic support for it in the
arch SoC and dts folders.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Signed-off-by: Ioannis Glaropoulos <ioannis.glaropoulos@nordicsemi.no>
The prepended 0x causes DTC warnings and shouldn't be there.
Tested by compiling hello_world for nrf52840_pca10056 before and after.
Fixes#8334.
Signed-off-by: Alex Tereschenko <alext.mkrs@gmail.com>
This adds basic support for declaring gpio nodes in dts for nrf52.
The dts.fixup provides mapping for the generated defines to the config
defines currently used by the nrf gpio driver.
Existing boards that use nrf52 are updated.
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
- Changed define for SETTINGS_CONFIG_PAGE_SIZE from a hard coded value
to reference build system generated FLASH_ERASE_BLOCK_SIZE. This value
comes from 'erase-block-size' found in the dtsi file of devices.
- Modified nrf52840.dtsi to include definition for 'erase-block-size'
Fixes#7107
Signed-off-by: David Leach <david.leach@nxp.com>
Commit introduces support for watchdog configuration for Nordic
Semiconductor nRF SoCs in device tree.
Signed-off-by: Karol Lasończyk <karol.lasonczyk@nordicsemi.no>
With upcoming ICs that are not in the nRF5x family, rename the flash
driver and all its dependencies from nrf5 to nrf.
Should also fix the issue introduced by f49150cab6 which broke the
assignment of the flash device due to a partial rename.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
So far, DT did not support the flash driver name.
Any flash-controller should have the appropriate
flash driver that should be identified by its name.
This path adds generic support for extract the description
from the flash-controller node,
adds implementation of this property for all nrf5x targets.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Where missing add compatible = "soc-nv-flash". Also added a label for
all the soc-nv-flash that we might use in the future.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Similar addition was don previous for nRF52840.
Added flash-controller description and moved flash description to
it. Added property for description of
the flash alignment required by write operations.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Similar addition was don previous for nRF52840.
Added flash-controller description and moved flash description to
it. Added property for description of
the flash alignment required by write operations.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Added flash-controller description and moved flash description to
it (for coherence). Added property for description of
the flash alignment required by write operations.
Thanks to that l-value FLASH_WRITE_BLOCK_SIZE macro
will be generated. It is useful for any component uses
the flash.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Remove memory node from skeleton dtsi and add device_type
property in every memory node in soc dtsi files
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
This patch add the unit-address component to memory and flash
nodes. According to the DT specification, the unit-address of
a node must match the first address specified in the reg
property of the node.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
This patch adds #address-cell, #size-cell properties to
cpus container node and device_type, reg properties to
cpu node.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Now that we can utilize label in the device tree we can convert to
getting the device name for the NRF UART out of the device tree
instead of from Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add device tree support for nRF51822 SoCs and Arduino 101-BLE,
Curie-BLE, BLE Nano, PCA10028-DK, and Quark-SE BLE boards. This
is minimal support for memory, flash, and UART.
Change-Id: I7e572bea537e384b6d66e520462f023ace0c9b35
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add device tree support for nRF52840 SoC and PCA10056-DK board. This
is minimal support for memory, flash, and UART.
For the nRF52840 we select between "nordic,nrf-uarte", "nordic,nrf-uart"
support for each board.
Change-Id: I1c377e0cb97ff4716ea5489fffaa7c0e2b34d18a
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add plumbing to build system and SoC level dtsi for the NRF52832 SoC.
We additionally add the necessary yaml files for the UART on the NRF52
SoCs.
Change-Id: I3b4a821b2993827e33d8e84bdbbc759d1521f8bd
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
