This commit makes it possible to use stm32flash for flashing (with west)
the STM32F030 Demo Board. OpenOCD is still the default, so in order to
use stm32flash, one must invoke ‘west flash’ with ‘-r stm32flash’.
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
In order to avoid pin configuration conflicts between peripherals,
add CONFIG_SERIAL flag to for each serial pinmux configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Several reviewers agreed that DT_HAS_NODE_STATUS_OKAY(...) was an
undesirable API for the following reasons:
- it's inconsistent with the rest of the DT_NODE_HAS_FOO names
- DT_NODE_HAS_FOO_BAR_BAZ(node) was agreed upon as a shorthand
for macros which are equivalent to
DT_NODE_HAS_FOO(node) && DT_NODE_HAS_BAR(node) &&
- DT_NODE_HAS_BAZ(node), and DT_HAS_NODE_STATUS_OKAY is an odd duck
- DT_NODE_HAS_STATUS(..., okay) was viewed as more readable anyway
- it is seen as a somewhat aesthetically challenged name
Replace all users with DT_NODE_HAS_STATUS(..., okay), which is
semantically equivalent.
This is mostly done with sed, but a few remaining cases were done by
hand, along with whitespace, docs, and comment changes. These special
cases include the Nordic SOC static assert files.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Rename DT_HAS_NODE to DT_HAS_NODE_STATUS_OKAY so the semantics are
clear. As going forward DT_HAS_NODE will report if a NODE exists
regardless of its status.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
For auto doc generation purpose, get name value of boards' yaml files
in sync with name provided as board name in .rst file
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Replace use of Kconfig UART_X symbols by calls to DT API.
Clean driver from symbols definitions
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use device node declaration instead.
Clean up GPIO_STM32_PORT* Kconfig symbols.
On some boards some gpio ports where disabled using Kconfig symbols.
Disable them now via device tree nodes in boards dts files.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Same deal as in commit eddd98f ("kconfig: Replace some single-symbol
'if's with 'depends on'"), for all symbols defined within defconfig
files. See that commit for an explanation.
Maybe 'if's were used originally to mirror the 'if's in the main Kconfig
files, and then it got copied around by people assuming 'if' must work
differently from 'depends on'. It doesn't match in every spot at least.
Better to keep it simple and just consistently use 'depends on' when
it's a single symbol/choice I think. Helps reinforce that 'if' isn't
magic too.
Verified by printing all Kconfig menu nodes (symbols, choices, menus,
etc.) before and after the change and diffing (should show no
difference).
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
All board defconfig files currently set the architecture in addition to
the board and the SoC, by setting e.g. CONFIG_ARM=y. This spams up
defconfig files.
CONFIG_<arch> symbols currently being set in configuration files also
means that they are configurable (can be changed in menuconfig and in
configuration files), even though changing the architecture won't work,
since other things get set from -DBOARD=<board>. Many boards also allow
changing the architecture symbols independently from the SoC symbols,
which doesn't make sense.
Get rid of all assignments to CONFIG_<arch> symbols and clean up the
relationships between symbols and the configuration interface, like
this:
1. Remove the choice with the CONFIG_<arch> symbols in arch/Kconfig and
turn the CONFIG_<arch> symbols into invisible
(promptless/nonconfigurable) symbols instead.
Getting rid of the choice allows the symbols to be 'select'ed (choice
symbols don't support 'select').
2. Select the right CONFIG_<arch> symbol from the SOC_SERIES_* symbols.
This makes sense since you know the architecture if you know the SoC.
Put the select on the SOC_* symbol instead for boards that don't have
a SOC_SERIES_*.
3. Remove all assignments to CONFIG_<arch> symbols. The assignments
would generate errors now, since the symbols are promptless.
The change was done by grepping for assignments to CONFIG_<arch>
symbols, finding the SOC_SERIES_* (or SOC_*) symbol being set in the
same defconfig file, and putting a 'select' on it instead.
See
https://github.com/ulfalizer/zephyr/commits/hide-arch-syms-unsquashed
for a split-up version of this commit, which will make it easier to see
how stuff was done. This needs to go in as one commit though.
This change is safer than it might seem re. outstanding PRs, because any
assignment to CONFIG_<arch> symbols generates an error now, making
outdated stuff easy to catch.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
CONFIG_BOARD_FOO is enabled in a number of board *_defconfig files
although it is useless as it is set by default (as defined as a
one option choice, symbol defaults to 'y').
CONFIG_BOARD_FOO should remain only in target that are defined
in boards providing multiple choices (dual cores, board with multiple
revisions).
Clean it from STM32 impacted boards.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Based on this commit
| commit dd6186f299
| Author: Bobby Noelte <b0661n0e17e@gmail.com>
| Date: Sat Sep 30 18:24:46 2017 +0200
|
| boards: nucleo_f030r8: reduce kernel memory usage
|
| nucleo_f030r8 fails in CI because applications need
| more RAM.
|
| Reduce kernel memory used by stacks and ISR vector table.
|
| Fixes#3923
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
dts pinctrl definitions were pushed in tree without the code
available to deal with it. They have been kept waiting for the
code, but this is taking much more time than initially thought.
So in current zephyr tree, for all STM32 boards, we have pinmux.c
file which is used to configure pins and these files that are
basically no-op. This situation is creating a lot of confusion
especially to new comers, and create useless maintenance effort.
Remove these files for now.
When zephyr will ready to use them, this commit could be reverted.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Move systick activation in soc/ as a Kconfig.defconfig file and
remove activation in boards _defconfig files.
This will allow to deactivate it in a more flexible way
with upcoming LPTIMER as tick source when power management
features are enabled.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
