Make I2C and SPI drivers for nRF SoCs no longer dependent on Kconfig
options that enable instances (i.e. I2C_x and SPI_x). Now these drivers
enable hardware instances when corresponding nodes in devicetree are
enabled (have status "okay").
For I2C, SPI, and UART drivers, instead of using Kconfig dependencies
to prevent enabling of hardware instances that cannot be used together
(e.g. SPIM1 and TWIM1), a file that signals invalid configurations with
build assertions is added to compilation.
Also dependencies on HAS_HW_NRF_* options are removed from Kconfigs
of I2C, SPI, and UART drivers, as for hidden options that activate
proper type of driver such dependencies are not actually helpful.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Remove prompts from Kconfig options `SPI_x_NRF_SPI*` that select the
type of nrfx driver (for SPI, SPIM, or SPIS peripheral) to be used
for a given instance. This prevents the options from being modified
in configuration files.
Instead, make one of these options selected by default according to the
"compatible" property set for the corresponding SPI node in devicetree.
This eliminates the need of changing both the "compatible" property in
devicetree and the Kconfig option selecting the driver type when a user
wants to switch between SPI, SPIM, and SPIS for a given instance.
Since all `SPI_x_NRF_SPI*` options are made "hidden" by this commit,
all their occurrences in configuration files are removed.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Same deal as in commit eddd98f811 ("kconfig: Replace some single-symbol
'if's with 'depends on'"), for the remaining cases outside defconfig
files. See that commit for an explanation.
Will do the defconfigs separately in case there are any complaints
there.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Update the hal_nordic module revision, to switch to nrfx 2.1.0.
Because the list of peripherals for nRF5340 has changed as follows:
- SPIM2 has been renamed to SPIM4
- SPIM2-3, SPIS2-3, TWIM2-3, TWIS2-3, and UARTE2-3 have been added
a couple of related corrections needed to be applied in dts and Kconfig
files, plus the spi_nrfx_spim driver has been extended with the support
for SPIM4.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
After switching to nrfx 2.0.0, the Kconfig choice options that allowed
enabling of pull-up or pull-down for MISO lines in SPIs and SPIMs are
not properly supported, they are simply ignored. This commit restores
the possibility of applying pull configuration for MISO lines.
In earlier nrfx versions, the MISO pull configuration could be only
set globally, in nrfx_config files, for all SPI and SPIM instances
together. Since nrfx 2.0.0, this configuration can be applied per
instance. This commit takes advantage of this possibility and instead
of using a common Kconfig option as a global setting for all instances,
allows applying individual instance settings via devicetree.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
By adding new SoC to Zephyr drivers has to be updated.
Commit affects:
- USB driver
- support for nRF52833 added.
- support for USB_DEVICE_REMOTE_WAKEUP in hid-mouse added.
- SPI
- IEEE 802.15.4
- CLOCK CONTROL
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Use a consistent way of enabling particular instances of peripherals
in nrfx drivers through options defined in modules/Kconfig.nordic,
to make the usage of nrfx drivers in Zephyr, especially the ones for
which there are no Zephyr driver shims (yet), easier.
Jira: NCSDK-2744
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add a Kconfig option to enable DMA for SPI with SOC_NRF52832 as long as
it being disabled due to Product Anomaly Notice (PAN) 58 is explicitly
overridden. This allows the SPIM driver to be enabled for the nRF52832
SoC for situations where PAN 58 is not a problem.
Signed-off-by: Andrew Fernandes <andrew@fernandes.org>
Rephrase prompts for a few options in drivers/spi/Kconfig.nrfx
so that their purpose is presented a bit better.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
In Nordic SoCs, SPI and TWI peripherals with the same instance number
share certain resources and therefore cannot be used at the same time
(in nRF91 Series this limitation concerns UART peripherals as well).
This patch adds Kconfig checks ensuring that only one of such mutually
exclusive peripherals can be enabled.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This patch adds missing SPI_3_NRF_SPIS Kconfig option (referenced by
`ext/hal/nordic/nrfx_config_nrf9160.h`, although not defined anywhere)
and adds support for SPIS3 instance in the nrfx_spis driver shim.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Use separate bindings for nRF Family SPI Slaves and SPI Masters so that
the properties "csn" and "def-char" can be made required for Slaves
(for Masters such settings are not applicable), and to avoid confusion
between the properties "csn" and "cs-gpios" for Master nodes.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Make the following nRF peripheral drivers:
- ADC
- GPIO
- I2C
- SPI
- UART
- USB_DEVICE
enabled by default so that users do not need to explicitly enable them
in their applications after choosing an nRF SoC as the build target.
Kconfig options enabling these drivers depend on both a given hardware
feature (e.g. I2C) and an nRF family SoC selected, so effectively they
will be automatically enabled only when it is adequate (and in most
cases these drivers are the only option for a given hardware feature
on nRF SoCs).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
All drivers require DTS for their primary SPI settings.
Removing SPI_[0-9]_NAME config option added some more samples changes.
Usage of these options there was anyway not relevant.
Fixes#11064
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This change adds DTS definition of SPI device for nRF chips.
It also removes SPI pin configuration from Kconfig and moves it to
chip DTS.
Signed-off-by: Filip Kubicz <filip.kubicz@nordicsemi.no>
In most Nordic SoCs the SPI and TWI peripherals with the same instance
number share certain resources and cannot be used at the same time.
In nRF52810 there are only single instances of these peripherals and
they are arranged in a different way so this limitation does not apply.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Selecting the type of driver (SPI, SPIM, or SPIS) to be used for
a given SPI instance is mandatory, so the "optional" modifier is
inappropriate for related choice options in the driver's Kconfig.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Use the HAS_HW_NRF_* symbols instead of the SOC_SERIES_NRF* ones
to filter out the driver options unavailable on particular SoCs.
Add comments explaining why the SPIM driver is not available for
nRF52832.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The following dependency loop existed:
config SPI_SLAVE
bool
(Defined at drivers/spi/Kconfig:27)
...is selected by...
config SPI_2_NRF_SPIS
bool
select SPI_SLAVE
(Defined at drivers/spi/Kconfig.nrfx:210)
...is in the choice...
choice
bool
depends on SPI_2
(Defined at drivers/spi/Kconfig.nrfx:192)
...that depends on...
config SPI_2
bool
depends on SPI_SLAVE
(Defined at
arch/x86/soc/intel_quark/quark_se/Kconfig.defconfig.series)
...that again depends on SPI_SLAVE
(This might not be a problem in practice, but it'd be difficult to
detect.)
I think the underlying issue is that SPI_2_NRF_SPIS 'select's SPI_SLAVE,
while SPI_2 'depends on' it.
Fix it by having SPI_2_NRF_SPIS 'depend on' SPI_SLAVE as well. This will
require SPI_SLAVE to be explicitly enabled before SPI_2_NRF_SPIS can be
enabled.
No configuration files in Zephyr itself seem to currently enable
SPI_2_NRF_SPIS (and it defaults to n), so no tweaks should be needed
there.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This adds a translation layer to make the nrfx driver for the nRF SPIS
(SPI Slave with EasyDMA) peripheral accessible via the Zephyr's API.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This adds a translation layer to make the nrfx driver for the nRF SPIM
(SPI Master with EasyDMA) peripheral accessible via the Zephyr's API.
The shim is provided only for nRF52840 because of a hardware anomaly
present in nRF52832. See Anomaly 58 (SPIM: An additional byte is clocked
out when RXD.MAXCNT = 1) in Errata for this chip.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This adds a translation layer to make the nrfx driver for the legacy
(i.e. without EasyDMA) nRF SPI peripheral accessible via the updated
Zephyr's API of the SPI driver.
Configuration files are already prepared for adding support for SPIM
(Master with EasyDMA) and SPIS (Slave with EasyDMA) peripherals.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
